Click to open or close... Double-click to open or close all.

Electron Injector System Requirements

General, functional and performance requirements associated with the Electron Injector Systems of the Electron Ion Collider.

Name
WBS
Description
Updated
Status
TBD
EIS : Electron Injector System

G-EIS.1
6.03
The EIS shall provide an electron beam having sufficient polarization as required by the ESR to meet the operational modes set forth in the Master Parameter Table (MPT). [Document#:EIC-SEG-RSI-005]
05/16/2025
Approved
FALSE

F-EIS-PREINJ.2
6.03.04
The EIS Pre-Injector shall be able to create a spin polarized electron bunch and accelerate it to 400MeV ready for transport to the 400 MeV-transfer line to the RCS.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS- PREINJ-BUNCH-MAG-HELM.1
6.03.04
The beam path between the gun and 1.3 GHz cavity shall be surrounded by magnetic field canceling Helmholtz coil to trim out the earth’s magnetic field.
05/16/2025
In Process
FALSE

F-EIS-GUN.1x
6.03.04
A compact Mott Polarimeter shall be used to inspect the polarization level and Quantum efficiency of the super lattice GaAs cathode, this system is not part of the gun chamber.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-LINAC-BNCHR-MAG-CORR.1
6.03.04
Multiple air-core Steering coils shall be placed in the bunching to correct the bunch position if needed (Number and positions TBD)
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-GUN.1
6.03.04
The pre-injector shall have a high voltage (HV) DC electron gun as the electron source for the EIC.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.3
6.03.04
When illuminated with a circular polarized laser the pre-injector electron gun shall produce the polarized electrons required to operate the EIC.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.4
6.03.04
The planned building utility requirements (Power, Temperature, Humidity, etc.) shall be consistent with the requirements necessary for the gun to meet its beam performance requirements
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-RCS.14
6.03.02
The RCS shall transmit polarization with a 97% efficiency
05/16/2025
In Process
FALSE

G-EIS.1xx
6.03
The EIS uptime shall be consistent with the overall uptime requirements of the EIC.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-ESR-INJ.2
6.03.03
Each electron bunch from the transfer line shall be injected into ESR in its own injection cycle. In a manner that minimizes the background on the detector system.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.13
6.03.02
The RCS shall reach an availability consistent with the overall availability of the entire EIC as specified in [5.9].
05/16/2025
In Process
FALSE

F-EIS.1x
6.03.04
The operational availability design target for the EIS shall be consistent with the operational availability target for the overall EIC as set forth in [Electron-Ion Collider Global Requirements, EIC-ORG-PLN-010]
05/16/2025
Not Applicable
FALSE

G-EIS.2
6.03
The EIS shall provide an electron beam having sufficient energy to meet the ESR beam requirements as set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
Approved
FALSE

F-EIS- PREINJ-LINAC-MAG.1
6.03.04
A Quadrupole triplet shall be installed between each accelerating structure in the LINAC to control the beam beta function and dispersion.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.2
6.03.04
The LINAC Quadrupole triplets shall be optimized to control beams with high RCS injection energies ~ 400[MeV].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.3
6.03.04
In addition to the Quadrupole triplets X Y steering coils shall be installed between each 2.856[GHz] accelerator structure to control the beam beta function and dispersion in the LINAC.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.4
6.03.04
A LINAC XY steering coils shall be optimized to control beams which have low RCS injection energies < < 400[MeV]
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.1
6.03.04
The Pre-Injector S-band LINAC shall be able to accelerate all electron bunches up to the energy's required by [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.2
6.03.04
The Pre-Injector LINAC frequency shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.3
6.03.04
The Pre-Injector LINAC rep-rate shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.1
6.03.02
The instrumentation system shall contain a Beam Position Monitor system consisting of dual-plane Beam Position Monitors adjacent to each quadrupole.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.2
6.03.02
Select Beam Position Monitors in the injection region shall have turn-by-turn orbit measurement capability based on a single, remotely selectable bunch out of the fully filled bunch train to enable injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.3
6.03.02
The instrumentation system shall include a beam current monitor to measure average beam current.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.4
6.03.02
The instrumentation system shall include a system to measure individual bunch charges and bunch pattern.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.5
6.03.02
The instrumentation system shall include a system to measure transverse bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.6
6.03.02
The instrumentation system shall include a system to measure longitudinal bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.7
6.03.02
The instrumentation system shall contain a betatron and synchrotron tune monitors.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.8
6.03.02
The longitudinal bunch profile monitor needs turn-by-turn capability based on a single bunch in the fully filled bunch train to allow timing and energy adjustment for injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.9
6.03.02
The RCS shall contain a beam-based alignment system.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.10
6.03.02
The RCS shall contain a beam loss monitor system at select regions.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.3
6.03.02
The sextupoles shall be sorted into appropriate “families” and powered accordingly.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.4
6.03.02
There shall be dipole correctors capable of adjusting the beam orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.6
6.03.02
The quadrupoles shall generally be arranged in a conventional FODO structure.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.7
6.03.02
Each quadrupole strength needs to be capable of being changed independently by small amounts for beam-based alignment purposes.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.8
6.03.02
Sextupoles shall be sorted into “families” with the family structure dependent on the linear lattice configuration (betatron phase advance per FODO cell).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.9
6.03.02
The maximum integrated field strength of the FODO sextupoles needs to be sufficient to correct chromaticity to within 1 unit in both planes.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.10
6.03.02
Window-frame dipole corrector magnets capable of providing both horizontal and vertical dipole fields to correct the beam orbit in both transverse planes shall be placed adjacent to most of the quadrupoles.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.11
6.03.02
The strength of the window-frame dipole correctors needs to be chosen to correct for any source of orbit distortion and should have a margin for beam based diagnostic purpose.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-GUN-INST.4
6.03.04
To characterize and control the fresh bunches sent to the Mott polarimeter, the gun diagnostic beamline shall contain instrumentation to measure and control the profile, position, and charge of the beam.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-INST.5
6.03.04
The Diagnostic beamline section shall have one Beam Profile Monitor and Wien Filter and an electrostatic bender before the Mott polarimeter and Faraday Cup.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-GUN-INST.6
6.03.04
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

F-EIS-GUN-MAG.1
6.03.04
Following the DC gun, the electron bunch shall be deflected through a bending dipole into the Bunching section
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.2
6.03.04
2 solenoids shall be placed between the gun and the bending dipole into the bunching section capable of correcting the beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.3
6.03.04
Provision shall be made for an appropriate number of air cored steering coils between the Gun and bunching section to correct the electron beam position as required.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.4
6.03.04
A bending dipole shall follow the Gun and be able to bend the beam from the gun into the bunching section OR bend separate electron bunches into the separate diagnostic beam line.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.5
6.03.04
The bending dipole after the gun shall also have the capability to deflect the beam enough to allow a laser to illuminate the photocathode head on.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.6
6.03.04
A minimum of three solenoids shall be placed between the gun and the first bunching cavity to maintain the beam size for 5–10 nC bunches
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.7
6.03.04
Short air core trim coils shall be used to correct beam position for energies greater than 100 keV
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.8
6.03.04
The Diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-VAC.3
6.03.04
The Laser section shall be independent from the Gun\diagnostic section vacuum.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN.3x
6.03.03
The low energy transfer line shall have an additional branch between the Gun and the Bunching section which can transfer individual electron bunches into the diagnostic beamline section.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.4x
6.03.03
The low energy transfer line shall have a laser port between the Gun and the Bunching section which will allow an optical path for the laser to illuminate the cathode face of the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.6x
6.03.04
The gun shall have steering coils to direct the liberated electrons (These can be reused from the existing Gun system.)
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-HETL-ESR-INJ.1
6.03.03
The transferred beam shall meet all the requirements of the circulating beam, for all operational modes of the ESR as set forth in [5.9].
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-INST-BPM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed Beam Position Monitors at the quadrupoles and at the entry and exit of a number of the dipoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-IC.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain FCT and an Integrating Current Transformer before the ESR injection septum.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-PM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed YAG\OTR at the entry and exit of a number of the diploes and quadrupoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-POL.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a system to measure the beam polarization.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-BUMP.1
6.03.03
ESR injection shall have three fast bump magnets to direct the bunches from the HETL into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker of the ESR injector system shall operate in unison with a septum magnet which can direct the beam into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-SLINE-FKICK.1
6.03.03
The ESR injection system shall have a fast strip line kicker with a rise time of 2nsecs .
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.1
6.03.03
The High Energy Transfer Line shall match the beam parameters between the extraction point of the RCS and injection point of the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.2
6.03.03
The extraction into the required High Energy transfer line shall match the ESR bunch spacing and spin pattern.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.3
6.03.03
The High Energy Transfer Line shall be spin transparent.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.4
6.03.03
The ESR extraction system shall have another three bump magnets, its own septum magnet and use the strip line injection kicker to extract and replace the circulating bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BLM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be a bunch length monitor(BLM) at the exit of the 3rd harmonic buncher cavity to measure bunch compression during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam position monitor (BPM) at the entry to the 1st harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section a beam position monitor (BPM) at the entry and exit of the 2nd harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.3
6.03.04
To characterize the beam as it exits the buncher section, beam position monitor(BPM) at the exit of the 3rd harmonic buncher cavity to measure beam position during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-EM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be an emittance monitor(EM), at the exit of the 3rd harmonic buncher cavity to measure beam position, the beam emittance during commissioning.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-EM.01
6.03.04.02.06
Emittances shall be measured using a profile monitor and a dedicated upstream quadrupole configured to measure H, V, and skew profiles.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.03
6.03.04.02.06
The EM shall be able to measure the expected normalized emittance of 40 um
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.02
6.03.04.02.06
Before the 400 MeV beam goes into the spin rotator, the emittance shall be measured by a quad scan
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.04
6.03.04.02.06
Beam emittance shall be measured in the low energy diagnostics beamline using a slit scanner and profile monitor
05/16/2025
On Hold
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.1
6.03.04
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), at the entry and exit of the 2nd harmonic buncher cavity to measure charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.2
6.03.04
To characterize the beam as it exits the buncher section, an integrating current transformer(ICT) at the exit of the 3rd harmonic buncher cavity to measure the bunch charge during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-LM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam loss monitor (BLM) at the entry to the 1st harmonic buncher cavity to measure beam loss
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a transverse profile monitor(TPM) at the entry to the 1st harmonic buncher cavity to measure the charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section there shall be a transverse profile monitor(TPM) at the entry and exit of the 2nd harmonic buncher cavity to measure the bunch profille.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.3
6.03.04
To characterize the beam as it exits the buncher section, transverse profile monitor(TPM) at the exit of the 3rd harmonic buncher cavity the bunch profile during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-MAG-SOL.4
6.03.04
The solenoidal field shall extend to also contain the 1st RF tank of the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-CAV.1
6.08
The LINAC TWP cavities shall be constant gradient cavities
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-INST-CM.1
6.03.04
Bunch charge measurements shall be performed at multiple locations through the LINAC.
05/16/2025
In Process
FALSE

F-EIS-LINAC-INST-PM.1
6.03.04
To measure the beam profile in the LINAC section there shall be a plunging YAG/OTR transverse profile monitor between the 1st and 2nd accelerating cells.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-QUAD.3
6.03.04
A drift space with quadrupole triplets shall be placed between each TWP structure to tune the bunch beta function through the LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.3
6.03.04
Between each S-band LINAC section there shall be at least two window frame steering magnets.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.4
6.03.04
Additionally, window frame steering magnets will be placed at the entry and exit of each accelerating structure to position the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.1
6.03.04
Following the Zigzag there shall be a de-chirp cavity to linearize and reduce the energy spread of the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.2
6.03.04
At the end of the Zigzag there shall be a diagnostic section (details TBD) to measure the bunch length and dP/P.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-DIP.1
6.03.04
The ZigZag section shall consist of a number of dipoles separated by drift spaces in a R56 configuration to increase the bunch length to 40ps.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-QUAD.1
6.03.04
The ZigZag section shall consist of a number of Quadrapoles to control the beam dispersion through the zigzag.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.1
6.03.04
A longitudinal matching section shall follow the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.2
6.03.04
The longitudinal matching section shall consist of a so-called Zigzag section followed by a de-chirp cavity which will stretch the bunch length to 40 ps, reduce the energy spread, and generate a longitudinal phase space rotation of the bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.3
6.03.04
At the Zigzag exit, the electron beam’s average spin orientation shall be longitudinal in the direction of beam travel.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.1
6.03.03
The fast kicker magnet shall be capable of deflecting the electron beam from the RCS to counter the RF kick.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.2
6.03.03
The fast kicker magnet shall follow the rise and fall of the amplitude of the RF sinusoidal functions
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST-BPM.1
6.03.03
To control the beam through the Spin Rotator section there shall be a Beam Position Monitors placed throughout the spin rotator as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST.1
6.03.03
To measure and control the beam in the medium energy 400 MeV transfer line there shall be sufficient beam position monitors for orbit control, transverse profile monitors, and bunch charge monitors as required.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

F-EIS-METL-MAG-DIP.1
6.03.03
At the entry to the spin rotator section before the spin rotator solenoid there shall be a number of bending dipole to rotate the polarization spin from the Longitudinal direction into the transverse X direction.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-DIP.2
6.03.03
After the exit of spin rotator solenoid, there shall be a number of bending dipoles to close the geometry and direct the beam into the medium energy 400[MeV] transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.4
6.03.03
The spin rotator entry quadrupole shall have at least 2 families this is needed to control the electron beam optics as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.6
6.03.03
The spin rotator exit quadrupoles shall have at least 2 families this is required to control the electron beam optics as needed.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.7
6.03.03
The spin rotator solenoid shall rotate the electron beam spin from the X axis to the vertical y-axis before it enters the medium [400MeV] transport line to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.8
6.03.03
The spin rotator solenoid shall have an integrated gradient of 2.2 [T.m] required to rotate the spin from the horizontal axis to the vertical axis.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.1
6.03.03
The bump magnets shall have a rise and time consistent with the requirements of the circulating bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.2
6.03.03
The Pulsed bump magnets shall be able to create a closed orbit path passing close to the Septum and maintain it during each injection cycle (100-150 Hz).
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.6
6.03.03
Each train of four bunches shall be injected into neighboring RF buckets to facilitate bunch merges.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.7
6.03.03
The injection system shall be capable of maintaining the small spacing required by the injected bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.11
6.03.03
The injection system into the RCS shall be capable of injecting successive bunches into the RCS to create a bunch train with four bunches each circulating in the RCS ready to be merged.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.12
6.03.03
The RCS shall be capable of merging each train of 4 bunches into a larger single bunch to create larger single circulating bunche in the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.1
6.03.03
The Medium energy transfer line shall transfer the beam from the pre-injector longitudinal matching section to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.2
6.03.03
The Medium energy transfer line shall contain 3 sections: 1. Spin rotation section, 2. The main transfer line, 3. The Injector system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.3
6.03.03
There will be number of corrector Quadrupoles after the Pre-Injector longitudinal matching and before the spin rotator to provide beam matching into the Spin Rotator.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.4
6.03.03
The medium energy 400 MeV transfer line shall be able to transport the spin reoriented beam from the spin rotator to the RCS injection system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.5
6.03.03
The medium energy 400 MeV transfer line will maintain the spin direction of the beam along the entire transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH-INST.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be beam position monitor (BPM), and a transverse profile monitor at the entry to the buncher cavity to measure beam loss, position, and charge.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.2
6.06.03
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), beam position monitors and transverse profile monitors
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.3
6.06.03
To characterize the beam as it exits the buncher section, there shall be an emittance measurement including slit and beam viewer, an integrating current transformer, beam position monitor, charge and compression during commissioning.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-RF.1
6.08
one 197 MHz buncher cavity shall be used for providing bunch chirp
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.1
6.03.03
The pre-injector LEBT low energy RF section shall transfer the electron beam from the gun to the linac section. shall provide bunching and initial acceleration to each 1 nC bunch
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.2
6.08
The bunching section shall generate sufficient compression to compress the bunch length to that required by [5.9].
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.3
6.08
The bunchers rf voltage and phase will be synchronized so that the passing electron bunches meet the required beam characteristics at the end of the buncher section.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.4
6.08
The Pre-Injector layout shall accommodate all RF cavities and allow enough room for other Pre-Injector components.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-GUN.2
6.03.04
The pre-injector electron gun shall produce all the bunch patterns required to deliver the ESR beam requirements set forth in [5.9].
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.21
6.03.04
The diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.1
6.03.03
The pre-injector shall have a low energy transfer line from the gun into the beam compression "Bunching" section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.6
6.03.04
Following the gun, there shall be multiple groups of magnets required to control the electron beam.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.7
6.03.04
To characterize and control the fresh bunches the low energy transfer line from the Gun to the Buncher shall contain a plunging transverse profile monitor, a bunch charge monitor, beam loss monitors, and beam position monitors
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LINAC-VAC.1
6.03.04
The LINAC section shall contain enough strategically located Vacuum gate valves, to allow access to the vacuum volume as needed.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-MAG-QUAD.1
6.03.03
The corrector Quadrupoles shall be able to suppress the βx and βy along the transfer line to levels consistent with those required ate the RCS injection kicker.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.2
6.03.03
The injection system shall inject the beam at Need update
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.9
6.03.03
The injection system shall contain 3 bump magnets to locally bump the RCS circulating beam close to the injection septum.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.11
6.03.03
The magnetic field of the injection system pulsed magnet shall follow the rise time of the power amplifiers which drive the RF kickers..
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ.1
6.03.04
The EIS Pre-Injector shall consist of 3 sub-systems: 1. An electron gun section, followed by 2. A low energy transfer line and bunching section, followed by 3. A LINAC section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-INST.1
6.03.04
EIS shall have all the beam instrumentation necessary to deliver the operational parameters set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-HETL-INST-BPM-ELEC.01
6.03.03.04.01
The BPM single bunch measurement resolution for a (1 - 4 nC) pilot bunch shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.02
6.03.03.04.01
The BPM single bunch measurement resolution for (5.5 - 28 nC) bunches shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.03
6.03.03.04.01
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.04
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used to measure the transport lattice.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.01
6.03.03.04.01
The BPM Pickup alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.02
6.03.03.04.01
The BPM Pickup shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.04
6.03.03.04.01
The BPM Pickups shall be located by the dipole correctors at every second quadrupole.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM-ELEC.01
6.03.03.04.01
For a (1 nC) pilot bunch, the BPM single bunch measurement resolution shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.02
6.03.03.04.01
For (5.5 - 10 nC) bunches, the BPM single bunch measurement resolution shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.03
6.03.03.04.01
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.04
6.03.03.04.01
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.01
6.03.03.04.01
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.02
6.03.03.04.01
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.04
6.03.03.04.01
The location of the BPM Pickups shall be TBD
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.01
6.03.02.05.04
A synchrotron light monitor (SLM) shall be installed in the RCS ring downstream of an RCS dipole magnet
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.02
6.03.02.05.04
The location of the SLM light extraction port shall be- TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.03
6.03.02.05.04
The synchrotron light shall be transported from the RCS light extraction port to an optical table for detection.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.04
6.03.02.05.04
The synchrotron light optical table shall have a streak camera and gated camera shall be installed.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.05
6.03.02.05.04
The SLM shall be able to make Turn-by-turn measurements using gated cameras to provide measurements of; the injection matching parameters and the beam position stability parameters during acceleration. TBD -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.06
6.03.02.05.04
The SLM shall be used to provide horizontal and vertical transverse profile measurements on bunches with charges > 6nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.07
6.03.02.05.04
The SLM horizontal and vertical transverse profile measurements shall be measured with a resolution in both planes of 0.1 mm
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.08
6.03.02.05.04
The SLM shall be used to provide longitudinal profile measurements
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.09
6.03.02.05.04
A dual sweep streak camera shall be used to provide measurements of the bunch length and longitudinal profiles
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.10
6.03.02.05.04
The dual sweep streak camera shall have a resolution of <5 ps
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.11
6.03.02.05.04
The profile measurements shall be used, together with modeled or measured beam optics to infer the beam emittances and energy spread.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.12
6.03.02.05.04
The Vertical emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.6 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.13
6.03.02.05.04
The Horizontal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 10 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.14
6.03.02.05.04
The Longitudinal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.00001 eV-s
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.15
6.03.02.05.04
The Energy spread measurement, for bunch charges > 6nC, shall be measured with a precision of 0.0001 dp/p
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.01
6.04.06.02
A bunch pattern monitor shall be installed in the ESR to measure indiviual bunch charge with an accuracy 1 %
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.02
6.04.06.02
The Bunch pattern monitor shall be capable of measuring Bunch patterns ranging from a single bunch, to a filled ring with 1,160 bunches
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.01
6.04.06.05
BLM shall be needed to needed to protect sensitive equipment.
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.02
6.04.06.05
The number of BLM installed in the ESR shall be TBD ea
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.03
6.04.06.05
BLM shall be installed at the following locations in the ESR TBD
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.04
6.04.06.05
The sensitivity of the BLM detectors shall be TBD units?
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.05
6.04.06.05
Where possible existing RHIC BLM's can be relocated to identify ESR & HSR losses
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.06
6.04.06.05
The response time from loss detection to abort shall be TBD us
05/16/2025
In Process
FALSE

P-ESR-INST-BPM-ELEC.01
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following capabilities defined for the low intensity pilot injection energies and high intensity collision energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following time resolutions for data refresh defined for the beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.03
6.04.06.01
The ESR BPM Electronics shall have the following time resolutions for data logging defined for the beam energies:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.04
6.04.06.01
The ESR BPM Electronics shall have the following measurement resolutions defined for beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.05
6.04.06.01
The ESR BPM Electronics shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.06
6.04.06.01
The ESR BPM Electronics shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-PU.01
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall provide dual plane (horizontal and vertical) beam positional measurements.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) shall be positioned in the following locations approved by physics as defined in the lattice:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.03
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) mechanical and electrical center in the locations identified shall be:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.04
6.04.06.01
The ESR Beam Position Monitor Pick-Ups housing shall have a +/- 10 (mrad) corresponding to +/- 0.6 (degree) roll tolerance with regards to BPM measurements in respect to the vacuum chamber.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.05
6.04.06.01
The ESR Beam Position Monitor Pick-Ups design shall be less than or equal to the allocated impedance and is within the accepted overall ESR impedance budget approved by physics. (replace with loss factor)
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.06
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall fulfill resolution requirements over the horizontal and vertical beam position range with respect to its fiducials of +/- 3 (mm).
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.07
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to ensure the maximum temperatures of the components (due to heating by the beam) are acceptable for reliability and operations of the EIC over the planned operational life of 20 (yrs).
09/15/2025
In Process
FALSE

P-ESR-INST-BPM-PU.09
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to be baked to 250 °C for UHV processing.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.10
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.11
6.04.06.01
The ESR BPM Pickup shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/30/2025
In Process
FALSE

P-ESR-INST-BPM-PU.12
6.04.06.01
The ESR Beam Position Monitor Button configuration will be mirror symmetric with respect to the mid-and center planes. Deviation from symmetry shall be such that corresponding BPM reading errors are less then 20 microns.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.13
6.04.06.01
The ESR Beam Position Monitor Pick-Ups symmetrical configuration (postion between the four buttons and the relative to the fiducials on top of the button) shall be stable under the inference of the expected operational thermal changes to the extent that corresponding changes in the bpm reading deviate less than 20 µm.
07/25/2025
Approved
FALSE

P-ESR-INST-DCCT.01
6.04.06.02
A DCCT shall measure the average beam current in the ESR.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.02
6.04.06.02
The measurement resolution averaged over 1 sec shall be < 5 uA
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.03
6.04.06.02
The DCCT beamline device impedance shall be approved by beam physics.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.04
6.04.06.02
Measurement drift tolerance (thermal effects) shall be ≤ 1 uA/K
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.05
6.04.06.02
The DCCT sensor in the ring shall operate in the temperature range of 15 to 35 degrees C
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.06
6.04.06.02
The range of average beam current to be measured shall be 0.156x10-3 to 2.5 A
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.07
6.04.06.02
The DCCT system shall have a remote controlled self calibration system
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.08
6.04.06.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.09
6.04.06.02
The measured average current shall be provided to users at a rate of 10 Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.10
6.04.06.02
The measured average current shall be archived at a rate of 10 Hz Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.11
6.04.06.02
The DCCT sensor assembly in the ring shall be radiation resistant
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.01
6.04.06.03
The requirements for longitudinal feedback are ??? TBD
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.02
6.04.06.03
The Longitudinal feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.01
6.04.06.04
The ESR shall have two synchrotron light monitors (SLM) and one X-ray pin hole monitor
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.02
6.04.06.04
The longitudinal bunch profile monitor shall have a turn-by-turn capability based on a single bunch in the fully filled bunch train.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.03
6.04.06.04
TThe SLM systems shall measure the crabbing angle, longitudinal bunch parameters, H & V beam size and global coupling.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.04
6.04.06.04
The SLM shall be able to measure a crabbing angle of 12.5 mrad with accuracy of 10 %
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.05
6.04.06.04
The SLM shall be able to measure the Longitudinal bunch parameters with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.06
6.04.06.04
The SLM shall be able to measure the H & V beam size with accuracy of H=?? V=?? units
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.07
6.04.06.04
The SLM shall be able to measure the Global coupling with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.08
6.04.06.04
One SLM port shall be located downstream of a dipole in an appropriate location in the ESR, exact location not critical.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.09
6.04.06.04
The second SLM port shall be located in a complimentary location in the lattice to ensure all the necessary SLM measurements can be made. TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.10
6.04.06.04
The SLM light extraction port mirrors shall be good quality, having a surface finish better than 1/10 Lambda
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.11
6.04.06.04
The SLM light extraction port mirrors shall be water cooled to avoid image distortion.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.12
6.04.06.04
There shall be an enclosed SL transport from the light extraction port to the SLM optical lab rooms. Length to be determined by the distance to optical lab room, should be minimized to reduce vibration problems.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.13
6.04.06.04
The locations of the SLM optical lab rooms shall be TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.14
6.04.06.04
The double-slit interferometer method shall be used to measure transverse beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.15
6.04.06.04
The standard transverse resolution of an SLM using visible light shall be ~60 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.16
6.04.06.04
The resolution using the double-slit method shall equal to 10 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.17
6.04.06.04
A streak camera shall be used to measure the bunch longitudinal profiles
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.18
6.04.06.04
A position sensitive photo-diode will provide photon beam centroid information which shall supplement the orbit stability measurements by the BPMs
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.19
6.04.06.04
A GigE CCD/CMOS camera, externally triggerable with exposure times ranging from 10 nsec to 5 sec, shall be used to image the visible radiation
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.20
6.04.06.04
A commercially available gated camera with gate width of <2 nsec (compared to a minimum bunch spacing of 10 nsec) shall be used to detect injection oscillations and for beam studies.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.21
6.04.06.04
The location of the X-ray pinhole monitoring system shall be TBD
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.22
6.04.06.04
The target resolution of the X-ray pin hole monitoring system shall be ~ 5 um (or as best that can be achieved with the machine parameters and commercial equipment) 5 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.23
6.04.06.04
The X-ray pin hole monitor shall provide independent measurement of the energy spread and horizontal/vertical emittance. H=V=15.4 nm
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.24
6.04.06.04
The X-ray pinhole photon beamline shall be equipped with gated cameras that will be employed to provide high resolution turn-by-turn profile measurements
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.25
6.04.06.04
A pinhole assembly including tungsten slits shall provide sufficient resolution to precisely measure the beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.26
6.04.06.04
Several different size pinholes sizes shall be incorporated to allow easy alignment and measurements at different beam currents and energies.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.01
6.04.06.03
Stripline kickers (H & V) shall be used to excite the beam so tunes can be measured using turn-by-turn BPM data.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.02
6.04.06.03
The magnitude of the kick required for the horizontal kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.03
6.04.06.03
The magnitude of the kick required for the vertical kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.04
6.04.06.03
The kicker waveform (risetime and shape) requirements shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.05
6.04.06.03
The location of the tune meter kicker striplines in the ESR shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.06
6.04.06.03
The impedance of the kicker beamline device shall be approved by beam Physics.
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.01
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.03
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.02
6.04.06.03
The transverse feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSSLFB.01
6.04.06.03
The transverse slow feedback system bandwidth shall bs 10 Hz
05/16/2025
In Process
FALSE

F-EIS-METL-MAG-SPINSOL.5
6.03.03
The spin rotator quadrupoles after the Spin rotator solenoid shall be able to match the beam beta functions βx and βy to that required for entry into the 400MeV transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.6
6.03.03
The spin rotator shall ensure the spin direction of the electron bunches are rotated from the longitudinal Z axis to the vertical Y axis.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-SEP.1
6.03.03
The septum magnet shall be capable of deflecting the incoming electron beam into the RCS and shielding the circulating beam already in the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.1
6.03.03
The LTR transfer line shall terminate with an injection system capable of transferring the beam into the RCS for all the operating energies and conditions specified in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.3
6.03.03
The vertically spin polarized electron bunch patterns generated by the pre-injector shall be transferred into the RCS unaltered.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.4
6.03.03
The injection system shall be able to inject one bunch per injection kick using RF and magnetic kickers to build up a total of 8 bunches from 4 kicks to the RF and kickers.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.5
6.03.03
The injection system shall ensure the bunch emittance shall match the requirements of the RCS RF system and such, to avoid collective instabilities and to stay within the off-momentum aperture.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.10
6.03.03
The RCS injection system shall contain an RF kicker and a pulsed magnet followed by a septum magnet to redirect the beam into the RCS closed orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.1
6.08
There shall be a special RF kicker to kick the injected beam into neighboring RF buckets without disturbing the 8 circulating bunches.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.2
6.08
The special kicker shall consist of an RF harmonic kicker with fundamental frequency of 1/4 of the main RCS RF cavity or compatible equivalent alternative.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.3
6.08
The special kicker shall have a rise and fall time that matches the RF bucket size.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.4
6.08
The special kicker shall have a peak power necessary to generate a kick to inject the bunch into the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.5
6.08
The special kicker shall have a macro pulse with a flattop that is greater than the time between the LINAC bunches and shall have a rise and fall time less than 1 RCS turn.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.6
6.08
The special kicker shall be able to repeat at the LINAC pulse rate.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT.28
6.03.03
The LTR transfer line shall have several FODO quadrupoles to control the beta function along the transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ.3
6.03.04
The EIS Pre-Injector shall create bunches which meet the requirements set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-RCS-MAG-QUAD.5
6.03.02
The quadrupoles shall be individually powered with low supplementary current/voltage power supplies for beam-based alignment purposes.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.7
6.03.02
The RCS straight sections shall have the appropirate number of defocusing and focusing quadrupole families per straight section.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.9
6.03.02
The non-colliding straights will have different scheme.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.14
6.03.02
The main arc quadrupoles shall be powered by a total of 2 power circuits 1 for focusing the other defocusing.
05/16/2025
In Process
FALSE

F-EIS-RCS-MAG.15
6.03.02
The quadrupoles in both straight sections shall need a total of 6 power circuits to power all six families of quadrupoles in both straights. (straights are optically identical)
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.18
6.03.02
The RCS magnets shall be fed by a system of power supplies matched in voltage and maximum current to the specifications and requirements of the respective magnets.
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-BUMP.1
6.03.03
the RCS extraction system shall have three fast bump magnets to direct the bunches to the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-FKICK.1
6.03.03
RCS extraction shall be facilitated with a fast kicker having a rise time of 2 micro-secs
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker shall operate in unison with a septum magnet which can direct the beam into the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.1
6.03.03
The beam injection of the electron bunches from the RCS into the ESR ring shall take place in the 12 o’clock straight section.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.2
6.03.03
There will be two electron bunches circulating in the RCS at extraction, these shall be injected into the High Energy Transfer Line which connects the RCS to the ESR.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.1
6.08
The RF system shall Provide a maximum RF voltage of 60MV to accelerate the beam.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.2
6.08
The total RF power provided by the RF amplifiers shall be able to compensate for all additional losses created by the stored electron beam in addition to the acceleration and synchrotron losses.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.3
6.08
The RF system shall Provide sufficient gradient to allow installation of all necessary RF modules in the limited space in IR 10.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.4
6.08
The RF system shall be able to accommodate 4 circulating bunches in one trains of 4 bunches.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.5
6.08
The RF system shall be able to merge the one train of 4 bunches into two larger separate circulating bunches then merge these two large bunches into a single larger circulating bunch.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.6
6.08
The RF system shall be able to accelerate final large, merged bunch to the operating energies needed by the ESR as set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.7
6.03.02
The RF system controls shall be designed to handle the transient beam loading for all bunch structures.
05/16/2025
In Process
FALSE

F-EIS-RCS-VAC.1
6.03.02
The vacuum chamber shall provide sufficient horizontal and vertical aperture to accommodate a beam which is 5 σ larger than the largest sigma beam size determined by the injected RMS emittance.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.2
6.03.02
The average dynamic pressure around the ring shall be < 5e-8[Torr] after 1 year of operation.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.3
6.03.02
The impedance of the entire RCS vacuum system shall allow for the bunch intensities, beam currents, and bunch numbers contained in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.09
6.03.02.04
The vacuum chamber shall be capable of absorbing and carrying away the eddy current power.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.4
6.03.02
The vacuum chamber and all its components shall be designed to withstand the total synchrotron radiation loads seen in operation.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-VAC.08
6.03.02.04
The vacuum chamber shall be capable of absorb synchrotron radiation and carrying away the absorbed power.
05/16/2025
Approved
FALSE

F-EIS-RCS.1
6.03.02
The RCS shall consist of two parts 1. The main RCS Ring, and 2. The High energy transfer line terminating with the ESR injection system
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.2
6.03.03
The RCS shall be capable of accepting the bunches and matching the bunch parameters as injected by the BAR into the LTR transfer line.
05/16/2025
In Process
FALSE

F-EIS-RCS.3
6.03.02
After bunch injection into the RCS, the RCS shall merge the injected bunches into two bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.4
6.03.02
After bunch injection the RCS shall be able to accelerate the single bunch to the final desired energy set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS.5
6.03.02
The RCS needs to accelerate to the top possible energy in a time interval consistent with the parameters set forth in [5.9] at approximately 100 msecs for 18 GeV.
05/16/2025
In Process
FALSE

F-EIS-RCS.6
6.03.03
The RCS shall be capable of kicking the accelerated bunches into the RTE transfer line to the ESR.
05/16/2025
In Process
FALSE

F-EIS-RCS.7
6.03.02
RCS will need to increase the vertical emittance to match the ESR vertical emittance.
05/16/2025
In Process
FALSE

F-EIS-RCS.8
6.03.02
The RCS shall have a racetrack design with 160 arc FODO cells, bending radius of 91.67 m and two 86.624 m straight sections made up of 8 FODO cells with a total circumference of 1.421 km
05/16/2025
In Process
FALSE

F-EIS-RCS.12
6.03.02
The alignment of the dipole field with respect to the vertical axis shall be less +/- 1 mrad rms with 2 sigma cut-off.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS-RCS.15
6.03.02
The RCS lattice shall contain provisions for correctors such as dipole correctors etc., as needed.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-TLINE-GUN-Diagnostic.1
6.03.04
The Pre-injector separate diagnostic beamline section shall have 3 branches one with Faraday cup, one port containing a connection to the cathode Laser and a line to a low energy beam dump.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.1
6.03.04
The instrumentation in the diagnostic beamline to the low energy beam dump shall have the capability to measure beam position, profile, bunch charge
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.4
6.03.04
The Faraday cup shall be able to measure the charge of the electron bunches from the gun.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-LASER-INST.1
6.03.04
There shall be instrumentation capable of measuring the position and profile of the laser beam on the cathode.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-LASER.1
6.03.04
The laser beam shall illuminate the cathode perpendicular to the cathode face
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.1
6.03.04
The beam tube and flange sizes shall be appropriate to transport polarized e-beam between the e-source and the diagnostic beam line polarimeter chamber.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.2
6.03.04
Vacuum system shall be compatible with UHV requirements.
05/16/2025
Not Applicable
FALSE

F-EIS-TLINE-SPIN.INST.1
6.03.03
Profile monitor, BPM are placed at before, in between and after two Wien filters
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.1
6.03.03
Between the dipole chamber and the bunching section, two Wien filters shall be used as spin rotator to rotate the spin direction from longitudinal to vertical.
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.2
6.03.03
triplets focusing are used in between the two Wien filters to maintain the beam envolop
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.3
6.03.03
Quadpole single let and double let are used before and after Wien to compensate the quadropole components from the Wien entrance and exit
05/16/2025
In Process
FALSE

F-EIS-VAC.1
6.03.04
The EIS vacuum system shall meet UHV standards at a minimum (Ref vacuum spec?)
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.07
6.03.02.04
On 15 m on each side (or one vacuum section) of the SRF cavities the vacuum system shall be processed to class ISO 5.
05/16/2025
Approved
FALSE

F-EIS-VAC.2
6.03.04
The impedance of the entire EIS vacuum system, including the transport lines, shall allow for the bunch intensities, beam currents, and bunch numbers contained in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.01
6.03.03.03
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.03
6.03.03.03
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.01
6.03.03.03
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.03
6.03.03.03
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-VAC.3
6.03.04
The size, location and type of vacuum pumps shall be chosen to meet the required vacuum levels during operation
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-VAC.4
6.03.04
Appropriate vacuum gauging shall be supplied in each vacuum sector to monitor the required vacuum levels
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

G-EIS.2x
6.06
The EIS shall contain appropirate protection systems to protect the magnine from damage and to minimise machine downtime
05/16/2025
Not Applicable
FALSE

F-EIS-CNTRL.3
6.07.02
The control system shall facilitate all machine protection systems required
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

F-EIS-HETL-ESR-INJ.2
6.03.03
Each electron bunch from the transfer line shall be injected into ESR in its own injection cycle. In a manner that minimizes the background on the detector system.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-DUMP.2
6.06.03
The LINAC shall have a Beam dump system (TBD).
05/16/2025
Not Applicable
FALSE

G-EIS.3
6.03
The EIS shall provide an electron beam with the RMS bunch momentum spread at extraction which meet the ESR beam requirements as set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
Approved
FALSE

F-EIS- PREINJ-LINAC-MAG.1
6.03.04
A Quadrupole triplet shall be installed between each accelerating structure in the LINAC to control the beam beta function and dispersion.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.2
6.03.04
The LINAC Quadrupole triplets shall be optimized to control beams with high RCS injection energies ~ 400[MeV].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.3
6.03.04
In addition to the Quadrupole triplets X Y steering coils shall be installed between each 2.856[GHz] accelerator structure to control the beam beta function and dispersion in the LINAC.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.4
6.03.04
A LINAC XY steering coils shall be optimized to control beams which have low RCS injection energies < < 400[MeV]
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.1
6.03.04
The Pre-Injector S-band LINAC shall be able to accelerate all electron bunches up to the energy's required by [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.2
6.03.04
The Pre-Injector LINAC frequency shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.3
6.03.04
The Pre-Injector LINAC rep-rate shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.1
6.03.02
The instrumentation system shall contain a Beam Position Monitor system consisting of dual-plane Beam Position Monitors adjacent to each quadrupole.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.2
6.03.02
Select Beam Position Monitors in the injection region shall have turn-by-turn orbit measurement capability based on a single, remotely selectable bunch out of the fully filled bunch train to enable injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.3
6.03.02
The instrumentation system shall include a beam current monitor to measure average beam current.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.4
6.03.02
The instrumentation system shall include a system to measure individual bunch charges and bunch pattern.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.5
6.03.02
The instrumentation system shall include a system to measure transverse bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.6
6.03.02
The instrumentation system shall include a system to measure longitudinal bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.7
6.03.02
The instrumentation system shall contain a betatron and synchrotron tune monitors.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.8
6.03.02
The longitudinal bunch profile monitor needs turn-by-turn capability based on a single bunch in the fully filled bunch train to allow timing and energy adjustment for injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.9
6.03.02
The RCS shall contain a beam-based alignment system.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.10
6.03.02
The RCS shall contain a beam loss monitor system at select regions.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.3
6.03.02
The sextupoles shall be sorted into appropriate “families” and powered accordingly.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.4
6.03.02
There shall be dipole correctors capable of adjusting the beam orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.6
6.03.02
The quadrupoles shall generally be arranged in a conventional FODO structure.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.7
6.03.02
Each quadrupole strength needs to be capable of being changed independently by small amounts for beam-based alignment purposes.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.8
6.03.02
Sextupoles shall be sorted into “families” with the family structure dependent on the linear lattice configuration (betatron phase advance per FODO cell).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.9
6.03.02
The maximum integrated field strength of the FODO sextupoles needs to be sufficient to correct chromaticity to within 1 unit in both planes.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.10
6.03.02
Window-frame dipole corrector magnets capable of providing both horizontal and vertical dipole fields to correct the beam orbit in both transverse planes shall be placed adjacent to most of the quadrupoles.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.11
6.03.02
The strength of the window-frame dipole correctors needs to be chosen to correct for any source of orbit distortion and should have a margin for beam based diagnostic purpose.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-GUN-INST.4
6.03.04
To characterize and control the fresh bunches sent to the Mott polarimeter, the gun diagnostic beamline shall contain instrumentation to measure and control the profile, position, and charge of the beam.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-INST.5
6.03.04
The Diagnostic beamline section shall have one Beam Profile Monitor and Wien Filter and an electrostatic bender before the Mott polarimeter and Faraday Cup.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-GUN-INST.6
6.03.04
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

F-EIS-GUN-MAG.1
6.03.04
Following the DC gun, the electron bunch shall be deflected through a bending dipole into the Bunching section
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.2
6.03.04
2 solenoids shall be placed between the gun and the bending dipole into the bunching section capable of correcting the beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.3
6.03.04
Provision shall be made for an appropriate number of air cored steering coils between the Gun and bunching section to correct the electron beam position as required.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.4
6.03.04
A bending dipole shall follow the Gun and be able to bend the beam from the gun into the bunching section OR bend separate electron bunches into the separate diagnostic beam line.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.5
6.03.04
The bending dipole after the gun shall also have the capability to deflect the beam enough to allow a laser to illuminate the photocathode head on.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.6
6.03.04
A minimum of three solenoids shall be placed between the gun and the first bunching cavity to maintain the beam size for 5–10 nC bunches
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.7
6.03.04
Short air core trim coils shall be used to correct beam position for energies greater than 100 keV
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.8
6.03.04
The Diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-VAC.3
6.03.04
The Laser section shall be independent from the Gun\diagnostic section vacuum.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN.3x
6.03.03
The low energy transfer line shall have an additional branch between the Gun and the Bunching section which can transfer individual electron bunches into the diagnostic beamline section.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.4x
6.03.03
The low energy transfer line shall have a laser port between the Gun and the Bunching section which will allow an optical path for the laser to illuminate the cathode face of the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.6x
6.03.04
The gun shall have steering coils to direct the liberated electrons (These can be reused from the existing Gun system.)
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-HETL-ESR-INJ.1
6.03.03
The transferred beam shall meet all the requirements of the circulating beam, for all operational modes of the ESR as set forth in [5.9].
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-INST-BPM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed Beam Position Monitors at the quadrupoles and at the entry and exit of a number of the dipoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-IC.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain FCT and an Integrating Current Transformer before the ESR injection septum.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-PM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed YAG\OTR at the entry and exit of a number of the diploes and quadrupoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-POL.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a system to measure the beam polarization.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-BUMP.1
6.03.03
ESR injection shall have three fast bump magnets to direct the bunches from the HETL into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker of the ESR injector system shall operate in unison with a septum magnet which can direct the beam into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-SLINE-FKICK.1
6.03.03
The ESR injection system shall have a fast strip line kicker with a rise time of 2nsecs .
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.1
6.03.03
The High Energy Transfer Line shall match the beam parameters between the extraction point of the RCS and injection point of the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.2
6.03.03
The extraction into the required High Energy transfer line shall match the ESR bunch spacing and spin pattern.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.3
6.03.03
The High Energy Transfer Line shall be spin transparent.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.4
6.03.03
The ESR extraction system shall have another three bump magnets, its own septum magnet and use the strip line injection kicker to extract and replace the circulating bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BLM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be a bunch length monitor(BLM) at the exit of the 3rd harmonic buncher cavity to measure bunch compression during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam position monitor (BPM) at the entry to the 1st harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section a beam position monitor (BPM) at the entry and exit of the 2nd harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.3
6.03.04
To characterize the beam as it exits the buncher section, beam position monitor(BPM) at the exit of the 3rd harmonic buncher cavity to measure beam position during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-EM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be an emittance monitor(EM), at the exit of the 3rd harmonic buncher cavity to measure beam position, the beam emittance during commissioning.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-EM.01
6.03.04.02.06
Emittances shall be measured using a profile monitor and a dedicated upstream quadrupole configured to measure H, V, and skew profiles.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.03
6.03.04.02.06
The EM shall be able to measure the expected normalized emittance of 40 um
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.02
6.03.04.02.06
Before the 400 MeV beam goes into the spin rotator, the emittance shall be measured by a quad scan
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.04
6.03.04.02.06
Beam emittance shall be measured in the low energy diagnostics beamline using a slit scanner and profile monitor
05/16/2025
On Hold
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.1
6.03.04
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), at the entry and exit of the 2nd harmonic buncher cavity to measure charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.2
6.03.04
To characterize the beam as it exits the buncher section, an integrating current transformer(ICT) at the exit of the 3rd harmonic buncher cavity to measure the bunch charge during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-LM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam loss monitor (BLM) at the entry to the 1st harmonic buncher cavity to measure beam loss
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a transverse profile monitor(TPM) at the entry to the 1st harmonic buncher cavity to measure the charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section there shall be a transverse profile monitor(TPM) at the entry and exit of the 2nd harmonic buncher cavity to measure the bunch profille.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.3
6.03.04
To characterize the beam as it exits the buncher section, transverse profile monitor(TPM) at the exit of the 3rd harmonic buncher cavity the bunch profile during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-MAG-SOL.4
6.03.04
The solenoidal field shall extend to also contain the 1st RF tank of the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-CAV.1
6.08
The LINAC TWP cavities shall be constant gradient cavities
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-INST-CM.1
6.03.04
Bunch charge measurements shall be performed at multiple locations through the LINAC.
05/16/2025
In Process
FALSE

F-EIS-LINAC-INST-PM.1
6.03.04
To measure the beam profile in the LINAC section there shall be a plunging YAG/OTR transverse profile monitor between the 1st and 2nd accelerating cells.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.3
6.03.04
Between each S-band LINAC section there shall be at least two window frame steering magnets.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.4
6.03.04
Additionally, window frame steering magnets will be placed at the entry and exit of each accelerating structure to position the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.2
6.03.04
At the end of the Zigzag there shall be a diagnostic section (details TBD) to measure the bunch length and dP/P.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.2
6.03.04
The longitudinal matching section shall consist of a so-called Zigzag section followed by a de-chirp cavity which will stretch the bunch length to 40 ps, reduce the energy spread, and generate a longitudinal phase space rotation of the bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.2
6.03.03
The fast kicker magnet shall follow the rise and fall of the amplitude of the RF sinusoidal functions
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST-BPM.1
6.03.03
To control the beam through the Spin Rotator section there shall be a Beam Position Monitors placed throughout the spin rotator as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST.1
6.03.03
To measure and control the beam in the medium energy 400 MeV transfer line there shall be sufficient beam position monitors for orbit control, transverse profile monitors, and bunch charge monitors as required.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

F-EIS-METL-MAG-DIP.1
6.03.03
At the entry to the spin rotator section before the spin rotator solenoid there shall be a number of bending dipole to rotate the polarization spin from the Longitudinal direction into the transverse X direction.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-DIP.2
6.03.03
After the exit of spin rotator solenoid, there shall be a number of bending dipoles to close the geometry and direct the beam into the medium energy 400[MeV] transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.5
6.03.03
The spin rotator quadrupoles after the Spin rotator solenoid shall be able to match the beam beta functions βx and βy to that required for entry into the 400MeV transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.6
6.03.03
The spin rotator exit quadrupoles shall have at least 2 families this is required to control the electron beam optics as needed.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.7
6.03.03
The spin rotator solenoid shall rotate the electron beam spin from the X axis to the vertical y-axis before it enters the medium [400MeV] transport line to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.8
6.03.03
The spin rotator solenoid shall have an integrated gradient of 2.2 [T.m] required to rotate the spin from the horizontal axis to the vertical axis.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.1
6.03.03
The bump magnets shall have a rise and time consistent with the requirements of the circulating bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.2
6.03.03
The Pulsed bump magnets shall be able to create a closed orbit path passing close to the Septum and maintain it during each injection cycle (100-150 Hz).
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.6
6.03.03
Each train of four bunches shall be injected into neighboring RF buckets to facilitate bunch merges.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.7
6.03.03
The injection system shall be capable of maintaining the small spacing required by the injected bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.11
6.03.03
The injection system into the RCS shall be capable of injecting successive bunches into the RCS to create a bunch train with four bunches each circulating in the RCS ready to be merged.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.12
6.03.03
The RCS shall be capable of merging each train of 4 bunches into a larger single bunch to create larger single circulating bunche in the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.2
6.03.03
The Medium energy transfer line shall contain 3 sections: 1. Spin rotation section, 2. The main transfer line, 3. The Injector system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.3
6.03.03
There will be number of corrector Quadrupoles after the Pre-Injector longitudinal matching and before the spin rotator to provide beam matching into the Spin Rotator.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.4
6.03.03
The medium energy 400 MeV transfer line shall be able to transport the spin reoriented beam from the spin rotator to the RCS injection system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.5
6.03.03
The medium energy 400 MeV transfer line will maintain the spin direction of the beam along the entire transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.6
6.03.03
The spin rotator shall ensure the spin direction of the electron bunches are rotated from the longitudinal Z axis to the vertical Y axis.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH-INST.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be beam position monitor (BPM), and a transverse profile monitor at the entry to the buncher cavity to measure beam loss, position, and charge.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.2
6.06.03
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), beam position monitors and transverse profile monitors
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.3
6.06.03
To characterize the beam as it exits the buncher section, there shall be an emittance measurement including slit and beam viewer, an integrating current transformer, beam position monitor, charge and compression during commissioning.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-RF.1
6.08
one 197 MHz buncher cavity shall be used for providing bunch chirp
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.2
6.08
The bunching section shall generate sufficient compression to compress the bunch length to that required by [5.9].
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.3
6.08
The bunchers rf voltage and phase will be synchronized so that the passing electron bunches meet the required beam characteristics at the end of the buncher section.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.4
6.08
The Pre-Injector layout shall accommodate all RF cavities and allow enough room for other Pre-Injector components.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-LINAC-VAC.1
6.03.04
The LINAC section shall contain enough strategically located Vacuum gate valves, to allow access to the vacuum volume as needed.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.1
6.03.03
The LTR transfer line shall terminate with an injection system capable of transferring the beam into the RCS for all the operating energies and conditions specified in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.3
6.03.03
The vertically spin polarized electron bunch patterns generated by the pre-injector shall be transferred into the RCS unaltered.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.1
6.08
There shall be a special RF kicker to kick the injected beam into neighboring RF buckets without disturbing the 8 circulating bunches.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ.1
6.03.04
The EIS Pre-Injector shall consist of 3 sub-systems: 1. An electron gun section, followed by 2. A low energy transfer line and bunching section, followed by 3. A LINAC section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-INST.1
6.03.04
EIS shall have all the beam instrumentation necessary to deliver the operational parameters set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-HETL-INST-BPM-ELEC.01
6.03.03.04.01
The BPM single bunch measurement resolution for a (1 - 4 nC) pilot bunch shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.02
6.03.03.04.01
The BPM single bunch measurement resolution for (5.5 - 28 nC) bunches shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.03
6.03.03.04.01
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.04
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used to measure the transport lattice.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.01
6.03.03.04.01
The BPM Pickup alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.02
6.03.03.04.01
The BPM Pickup shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.04
6.03.03.04.01
The BPM Pickups shall be located by the dipole correctors at every second quadrupole.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM-ELEC.01
6.03.03.04.01
For a (1 nC) pilot bunch, the BPM single bunch measurement resolution shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.02
6.03.03.04.01
For (5.5 - 10 nC) bunches, the BPM single bunch measurement resolution shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.03
6.03.03.04.01
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.04
6.03.03.04.01
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.01
6.03.03.04.01
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.02
6.03.03.04.01
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.04
6.03.03.04.01
The location of the BPM Pickups shall be TBD
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.01
6.03.02.05.04
A synchrotron light monitor (SLM) shall be installed in the RCS ring downstream of an RCS dipole magnet
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.02
6.03.02.05.04
The location of the SLM light extraction port shall be- TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.03
6.03.02.05.04
The synchrotron light shall be transported from the RCS light extraction port to an optical table for detection.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.04
6.03.02.05.04
The synchrotron light optical table shall have a streak camera and gated camera shall be installed.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.05
6.03.02.05.04
The SLM shall be able to make Turn-by-turn measurements using gated cameras to provide measurements of; the injection matching parameters and the beam position stability parameters during acceleration. TBD -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.06
6.03.02.05.04
The SLM shall be used to provide horizontal and vertical transverse profile measurements on bunches with charges > 6nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.07
6.03.02.05.04
The SLM horizontal and vertical transverse profile measurements shall be measured with a resolution in both planes of 0.1 mm
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.08
6.03.02.05.04
The SLM shall be used to provide longitudinal profile measurements
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.09
6.03.02.05.04
A dual sweep streak camera shall be used to provide measurements of the bunch length and longitudinal profiles
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.10
6.03.02.05.04
The dual sweep streak camera shall have a resolution of <5 ps
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.11
6.03.02.05.04
The profile measurements shall be used, together with modeled or measured beam optics to infer the beam emittances and energy spread.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.12
6.03.02.05.04
The Vertical emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.6 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.13
6.03.02.05.04
The Horizontal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 10 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.14
6.03.02.05.04
The Longitudinal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.00001 eV-s
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.15
6.03.02.05.04
The Energy spread measurement, for bunch charges > 6nC, shall be measured with a precision of 0.0001 dp/p
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.01
6.04.06.02
A bunch pattern monitor shall be installed in the ESR to measure indiviual bunch charge with an accuracy 1 %
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.02
6.04.06.02
The Bunch pattern monitor shall be capable of measuring Bunch patterns ranging from a single bunch, to a filled ring with 1,160 bunches
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.01
6.04.06.05
BLM shall be needed to needed to protect sensitive equipment.
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.02
6.04.06.05
The number of BLM installed in the ESR shall be TBD ea
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.03
6.04.06.05
BLM shall be installed at the following locations in the ESR TBD
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.04
6.04.06.05
The sensitivity of the BLM detectors shall be TBD units?
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.05
6.04.06.05
Where possible existing RHIC BLM's can be relocated to identify ESR & HSR losses
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.06
6.04.06.05
The response time from loss detection to abort shall be TBD us
05/16/2025
In Process
FALSE

P-ESR-INST-BPM-ELEC.01
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following capabilities defined for the low intensity pilot injection energies and high intensity collision energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following time resolutions for data refresh defined for the beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.03
6.04.06.01
The ESR BPM Electronics shall have the following time resolutions for data logging defined for the beam energies:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.04
6.04.06.01
The ESR BPM Electronics shall have the following measurement resolutions defined for beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.05
6.04.06.01
The ESR BPM Electronics shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.06
6.04.06.01
The ESR BPM Electronics shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-PU.01
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall provide dual plane (horizontal and vertical) beam positional measurements.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) shall be positioned in the following locations approved by physics as defined in the lattice:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.03
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) mechanical and electrical center in the locations identified shall be:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.04
6.04.06.01
The ESR Beam Position Monitor Pick-Ups housing shall have a +/- 10 (mrad) corresponding to +/- 0.6 (degree) roll tolerance with regards to BPM measurements in respect to the vacuum chamber.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.05
6.04.06.01
The ESR Beam Position Monitor Pick-Ups design shall be less than or equal to the allocated impedance and is within the accepted overall ESR impedance budget approved by physics. (replace with loss factor)
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.06
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall fulfill resolution requirements over the horizontal and vertical beam position range with respect to its fiducials of +/- 3 (mm).
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.07
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to ensure the maximum temperatures of the components (due to heating by the beam) are acceptable for reliability and operations of the EIC over the planned operational life of 20 (yrs).
09/15/2025
In Process
FALSE

P-ESR-INST-BPM-PU.09
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to be baked to 250 °C for UHV processing.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.10
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.11
6.04.06.01
The ESR BPM Pickup shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/30/2025
In Process
FALSE

P-ESR-INST-BPM-PU.12
6.04.06.01
The ESR Beam Position Monitor Button configuration will be mirror symmetric with respect to the mid-and center planes. Deviation from symmetry shall be such that corresponding BPM reading errors are less then 20 microns.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.13
6.04.06.01
The ESR Beam Position Monitor Pick-Ups symmetrical configuration (postion between the four buttons and the relative to the fiducials on top of the button) shall be stable under the inference of the expected operational thermal changes to the extent that corresponding changes in the bpm reading deviate less than 20 µm.
07/25/2025
Approved
FALSE

P-ESR-INST-DCCT.01
6.04.06.02
A DCCT shall measure the average beam current in the ESR.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.02
6.04.06.02
The measurement resolution averaged over 1 sec shall be < 5 uA
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.03
6.04.06.02
The DCCT beamline device impedance shall be approved by beam physics.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.04
6.04.06.02
Measurement drift tolerance (thermal effects) shall be ≤ 1 uA/K
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.05
6.04.06.02
The DCCT sensor in the ring shall operate in the temperature range of 15 to 35 degrees C
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.06
6.04.06.02
The range of average beam current to be measured shall be 0.156x10-3 to 2.5 A
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.07
6.04.06.02
The DCCT system shall have a remote controlled self calibration system
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.08
6.04.06.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.09
6.04.06.02
The measured average current shall be provided to users at a rate of 10 Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.10
6.04.06.02
The measured average current shall be archived at a rate of 10 Hz Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.11
6.04.06.02
The DCCT sensor assembly in the ring shall be radiation resistant
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.01
6.04.06.03
The requirements for longitudinal feedback are ??? TBD
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.02
6.04.06.03
The Longitudinal feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.01
6.04.06.04
The ESR shall have two synchrotron light monitors (SLM) and one X-ray pin hole monitor
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.02
6.04.06.04
The longitudinal bunch profile monitor shall have a turn-by-turn capability based on a single bunch in the fully filled bunch train.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.03
6.04.06.04
TThe SLM systems shall measure the crabbing angle, longitudinal bunch parameters, H & V beam size and global coupling.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.04
6.04.06.04
The SLM shall be able to measure a crabbing angle of 12.5 mrad with accuracy of 10 %
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.05
6.04.06.04
The SLM shall be able to measure the Longitudinal bunch parameters with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.06
6.04.06.04
The SLM shall be able to measure the H & V beam size with accuracy of H=?? V=?? units
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.07
6.04.06.04
The SLM shall be able to measure the Global coupling with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.08
6.04.06.04
One SLM port shall be located downstream of a dipole in an appropriate location in the ESR, exact location not critical.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.09
6.04.06.04
The second SLM port shall be located in a complimentary location in the lattice to ensure all the necessary SLM measurements can be made. TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.10
6.04.06.04
The SLM light extraction port mirrors shall be good quality, having a surface finish better than 1/10 Lambda
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.11
6.04.06.04
The SLM light extraction port mirrors shall be water cooled to avoid image distortion.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.12
6.04.06.04
There shall be an enclosed SL transport from the light extraction port to the SLM optical lab rooms. Length to be determined by the distance to optical lab room, should be minimized to reduce vibration problems.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.13
6.04.06.04
The locations of the SLM optical lab rooms shall be TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.14
6.04.06.04
The double-slit interferometer method shall be used to measure transverse beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.15
6.04.06.04
The standard transverse resolution of an SLM using visible light shall be ~60 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.16
6.04.06.04
The resolution using the double-slit method shall equal to 10 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.17
6.04.06.04
A streak camera shall be used to measure the bunch longitudinal profiles
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.18
6.04.06.04
A position sensitive photo-diode will provide photon beam centroid information which shall supplement the orbit stability measurements by the BPMs
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.19
6.04.06.04
A GigE CCD/CMOS camera, externally triggerable with exposure times ranging from 10 nsec to 5 sec, shall be used to image the visible radiation
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.20
6.04.06.04
A commercially available gated camera with gate width of <2 nsec (compared to a minimum bunch spacing of 10 nsec) shall be used to detect injection oscillations and for beam studies.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.21
6.04.06.04
The location of the X-ray pinhole monitoring system shall be TBD
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.22
6.04.06.04
The target resolution of the X-ray pin hole monitoring system shall be ~ 5 um (or as best that can be achieved with the machine parameters and commercial equipment) 5 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.23
6.04.06.04
The X-ray pin hole monitor shall provide independent measurement of the energy spread and horizontal/vertical emittance. H=V=15.4 nm
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.24
6.04.06.04
The X-ray pinhole photon beamline shall be equipped with gated cameras that will be employed to provide high resolution turn-by-turn profile measurements
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.25
6.04.06.04
A pinhole assembly including tungsten slits shall provide sufficient resolution to precisely measure the beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.26
6.04.06.04
Several different size pinholes sizes shall be incorporated to allow easy alignment and measurements at different beam currents and energies.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.01
6.04.06.03
Stripline kickers (H & V) shall be used to excite the beam so tunes can be measured using turn-by-turn BPM data.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.02
6.04.06.03
The magnitude of the kick required for the horizontal kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.03
6.04.06.03
The magnitude of the kick required for the vertical kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.04
6.04.06.03
The kicker waveform (risetime and shape) requirements shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.05
6.04.06.03
The location of the tune meter kicker striplines in the ESR shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.06
6.04.06.03
The impedance of the kicker beamline device shall be approved by beam Physics.
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.01
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.03
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.02
6.04.06.03
The transverse feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSSLFB.01
6.04.06.03
The transverse slow feedback system bandwidth shall bs 10 Hz
05/16/2025
In Process
FALSE

F-EIS-LINAC-MAG-QUAD.3
6.03.04
A drift space with quadrupole triplets shall be placed between each TWP structure to tune the bunch beta function through the LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.1
6.03.04
Following the Zigzag there shall be a de-chirp cavity to linearize and reduce the energy spread of the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-DIP.1
6.03.04
The ZigZag section shall consist of a number of dipoles separated by drift spaces in a R56 configuration to increase the bunch length to 40ps.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-QUAD.1
6.03.04
The ZigZag section shall consist of a number of Quadrapoles to control the beam dispersion through the zigzag.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.1
6.03.04
A longitudinal matching section shall follow the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.3
6.03.04
At the Zigzag exit, the electron beam’s average spin orientation shall be longitudinal in the direction of beam travel.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.1
6.03.03
The fast kicker magnet shall be capable of deflecting the electron beam from the RCS to counter the RF kick.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.4
6.03.03
The spin rotator entry quadrupole shall have at least 2 families this is needed to control the electron beam optics as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.1
6.03.03
The Medium energy transfer line shall transfer the beam from the pre-injector longitudinal matching section to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH.1
6.03.03
The pre-injector LEBT low energy RF section shall transfer the electron beam from the gun to the linac section. shall provide bunching and initial acceleration to each 1 nC bunch
05/16/2025
In Process
FALSE

F-EIS-PREINJ-GUN.2
6.03.04
The pre-injector electron gun shall produce all the bunch patterns required to deliver the ESR beam requirements set forth in [5.9].
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.21
6.03.04
The diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.1
6.03.03
The pre-injector shall have a low energy transfer line from the gun into the beam compression "Bunching" section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.6
6.03.04
Following the gun, there shall be multiple groups of magnets required to control the electron beam.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.7
6.03.04
To characterize and control the fresh bunches the low energy transfer line from the Gun to the Buncher shall contain a plunging transverse profile monitor, a bunch charge monitor, beam loss monitors, and beam position monitors
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-TLINE-MEBT-MAG-QUAD.1
6.03.03
The corrector Quadrupoles shall be able to suppress the βx and βy along the transfer line to levels consistent with those required ate the RCS injection kicker.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-SEP.1
6.03.03
The septum magnet shall be capable of deflecting the incoming electron beam into the RCS and shielding the circulating beam already in the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.2
6.03.03
The injection system shall inject the beam at Need update
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.4
6.03.03
The injection system shall be able to inject one bunch per injection kick using RF and magnetic kickers to build up a total of 8 bunches from 4 kicks to the RF and kickers.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.5
6.03.03
The injection system shall ensure the bunch emittance shall match the requirements of the RCS RF system and such, to avoid collective instabilities and to stay within the off-momentum aperture.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.9
6.03.03
The injection system shall contain 3 bump magnets to locally bump the RCS circulating beam close to the injection septum.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.10
6.03.03
The RCS injection system shall contain an RF kicker and a pulsed magnet followed by a septum magnet to redirect the beam into the RCS closed orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.11
6.03.03
The magnetic field of the injection system pulsed magnet shall follow the rise time of the power amplifiers which drive the RF kickers..
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.2
6.08
The special kicker shall consist of an RF harmonic kicker with fundamental frequency of 1/4 of the main RCS RF cavity or compatible equivalent alternative.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.3
6.08
The special kicker shall have a rise and fall time that matches the RF bucket size.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.4
6.08
The special kicker shall have a peak power necessary to generate a kick to inject the bunch into the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.5
6.08
The special kicker shall have a macro pulse with a flattop that is greater than the time between the LINAC bunches and shall have a rise and fall time less than 1 RCS turn.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.6
6.08
The special kicker shall be able to repeat at the LINAC pulse rate.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT.28
6.03.03
The LTR transfer line shall have several FODO quadrupoles to control the beta function along the transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ.3
6.03.04
The EIS Pre-Injector shall create bunches which meet the requirements set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-RCS-MAG-QUAD.5
6.03.02
The quadrupoles shall be individually powered with low supplementary current/voltage power supplies for beam-based alignment purposes.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.7
6.03.02
The RCS straight sections shall have the appropirate number of defocusing and focusing quadrupole families per straight section.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.9
6.03.02
The non-colliding straights will have different scheme.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.14
6.03.02
The main arc quadrupoles shall be powered by a total of 2 power circuits 1 for focusing the other defocusing.
05/16/2025
In Process
FALSE

F-EIS-RCS-MAG.15
6.03.02
The quadrupoles in both straight sections shall need a total of 6 power circuits to power all six families of quadrupoles in both straights. (straights are optically identical)
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.18
6.03.02
The RCS magnets shall be fed by a system of power supplies matched in voltage and maximum current to the specifications and requirements of the respective magnets.
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-BUMP.1
6.03.03
the RCS extraction system shall have three fast bump magnets to direct the bunches to the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-FKICK.1
6.03.03
RCS extraction shall be facilitated with a fast kicker having a rise time of 2 micro-secs
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker shall operate in unison with a septum magnet which can direct the beam into the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.1
6.03.03
The beam injection of the electron bunches from the RCS into the ESR ring shall take place in the 12 o’clock straight section.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.2
6.03.03
There will be two electron bunches circulating in the RCS at extraction, these shall be injected into the High Energy Transfer Line which connects the RCS to the ESR.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.1
6.08
The RF system shall Provide a maximum RF voltage of 60MV to accelerate the beam.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.2
6.08
The total RF power provided by the RF amplifiers shall be able to compensate for all additional losses created by the stored electron beam in addition to the acceleration and synchrotron losses.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.3
6.08
The RF system shall Provide sufficient gradient to allow installation of all necessary RF modules in the limited space in IR 10.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.4
6.08
The RF system shall be able to accommodate 4 circulating bunches in one trains of 4 bunches.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.5
6.08
The RF system shall be able to merge the one train of 4 bunches into two larger separate circulating bunches then merge these two large bunches into a single larger circulating bunch.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.6
6.08
The RF system shall be able to accelerate final large, merged bunch to the operating energies needed by the ESR as set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.7
6.03.02
The RF system controls shall be designed to handle the transient beam loading for all bunch structures.
05/16/2025
In Process
FALSE

F-EIS-RCS-VAC.1
6.03.02
The vacuum chamber shall provide sufficient horizontal and vertical aperture to accommodate a beam which is 5 σ larger than the largest sigma beam size determined by the injected RMS emittance.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.2
6.03.02
The average dynamic pressure around the ring shall be < 5e-8[Torr] after 1 year of operation.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.3
6.03.02
The impedance of the entire RCS vacuum system shall allow for the bunch intensities, beam currents, and bunch numbers contained in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.09
6.03.02.04
The vacuum chamber shall be capable of absorbing and carrying away the eddy current power.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.4
6.03.02
The vacuum chamber and all its components shall be designed to withstand the total synchrotron radiation loads seen in operation.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-VAC.08
6.03.02.04
The vacuum chamber shall be capable of absorb synchrotron radiation and carrying away the absorbed power.
05/16/2025
Approved
FALSE

F-EIS-RCS.1
6.03.02
The RCS shall consist of two parts 1. The main RCS Ring, and 2. The High energy transfer line terminating with the ESR injection system
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.2
6.03.03
The RCS shall be capable of accepting the bunches and matching the bunch parameters as injected by the BAR into the LTR transfer line.
05/16/2025
In Process
FALSE

F-EIS-RCS.3
6.03.02
After bunch injection into the RCS, the RCS shall merge the injected bunches into two bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.4
6.03.02
After bunch injection the RCS shall be able to accelerate the single bunch to the final desired energy set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS.5
6.03.02
The RCS needs to accelerate to the top possible energy in a time interval consistent with the parameters set forth in [5.9] at approximately 100 msecs for 18 GeV.
05/16/2025
In Process
FALSE

F-EIS-RCS.6
6.03.03
The RCS shall be capable of kicking the accelerated bunches into the RTE transfer line to the ESR.
05/16/2025
In Process
FALSE

F-EIS-RCS.7
6.03.02
RCS will need to increase the vertical emittance to match the ESR vertical emittance.
05/16/2025
In Process
FALSE

F-EIS-RCS.8
6.03.02
The RCS shall have a racetrack design with 160 arc FODO cells, bending radius of 91.67 m and two 86.624 m straight sections made up of 8 FODO cells with a total circumference of 1.421 km
05/16/2025
In Process
FALSE

F-EIS-RCS.15
6.03.02
The RCS lattice shall contain provisions for correctors such as dipole correctors etc., as needed.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-TLINE-GUN-Diagnostic.1
6.03.04
The Pre-injector separate diagnostic beamline section shall have 3 branches one with Faraday cup, one port containing a connection to the cathode Laser and a line to a low energy beam dump.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.1
6.03.04
The instrumentation in the diagnostic beamline to the low energy beam dump shall have the capability to measure beam position, profile, bunch charge
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.4
6.03.04
The Faraday cup shall be able to measure the charge of the electron bunches from the gun.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-LASER-INST.1
6.03.04
There shall be instrumentation capable of measuring the position and profile of the laser beam on the cathode.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-LASER.1
6.03.04
The laser beam shall illuminate the cathode perpendicular to the cathode face
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.1
6.03.04
The beam tube and flange sizes shall be appropriate to transport polarized e-beam between the e-source and the diagnostic beam line polarimeter chamber.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.2
6.03.04
Vacuum system shall be compatible with UHV requirements.
05/16/2025
Not Applicable
FALSE

F-EIS-TLINE-SPIN.INST.1
6.03.03
Profile monitor, BPM are placed at before, in between and after two Wien filters
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.1
6.03.03
Between the dipole chamber and the bunching section, two Wien filters shall be used as spin rotator to rotate the spin direction from longitudinal to vertical.
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.2
6.03.03
triplets focusing are used in between the two Wien filters to maintain the beam envolop
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.3
6.03.03
Quadpole single let and double let are used before and after Wien to compensate the quadropole components from the Wien entrance and exit
05/16/2025
In Process
FALSE

F-EIS-VAC.1
6.03.04
The EIS vacuum system shall meet UHV standards at a minimum (Ref vacuum spec?)
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.07
6.03.02.04
On 15 m on each side (or one vacuum section) of the SRF cavities the vacuum system shall be processed to class ISO 5.
05/16/2025
Approved
FALSE

F-EIS-VAC.2
6.03.04
The impedance of the entire EIS vacuum system, including the transport lines, shall allow for the bunch intensities, beam currents, and bunch numbers contained in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.01
6.03.03.03
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.03
6.03.03.03
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.01
6.03.03.03
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.03
6.03.03.03
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-VAC.3
6.03.04
The size, location and type of vacuum pumps shall be chosen to meet the required vacuum levels during operation
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-VAC.4
6.03.04
Appropriate vacuum gauging shall be supplied in each vacuum sector to monitor the required vacuum levels
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

G-EIS.4
6.03
The EIS pre-injector shall provide an electron beam to the ESR having a horizontal beam emittance which is compatible with operation of the ESR.
05/16/2025
Approved
FALSE

F-EIS- PREINJ-LINAC-MAG.1
6.03.04
A Quadrupole triplet shall be installed between each accelerating structure in the LINAC to control the beam beta function and dispersion.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.2
6.03.04
The LINAC Quadrupole triplets shall be optimized to control beams with high RCS injection energies ~ 400[MeV].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.3
6.03.04
In addition to the Quadrupole triplets X Y steering coils shall be installed between each 2.856[GHz] accelerator structure to control the beam beta function and dispersion in the LINAC.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.4
6.03.04
A LINAC XY steering coils shall be optimized to control beams which have low RCS injection energies < < 400[MeV]
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.1
6.03.04
The Pre-Injector S-band LINAC shall be able to accelerate all electron bunches up to the energy's required by [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.2
6.03.04
The Pre-Injector LINAC frequency shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.3
6.03.04
The Pre-Injector LINAC rep-rate shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.1
6.03.02
The instrumentation system shall contain a Beam Position Monitor system consisting of dual-plane Beam Position Monitors adjacent to each quadrupole.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.2
6.03.02
Select Beam Position Monitors in the injection region shall have turn-by-turn orbit measurement capability based on a single, remotely selectable bunch out of the fully filled bunch train to enable injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.3
6.03.02
The instrumentation system shall include a beam current monitor to measure average beam current.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.4
6.03.02
The instrumentation system shall include a system to measure individual bunch charges and bunch pattern.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.5
6.03.02
The instrumentation system shall include a system to measure transverse bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.6
6.03.02
The instrumentation system shall include a system to measure longitudinal bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.7
6.03.02
The instrumentation system shall contain a betatron and synchrotron tune monitors.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.8
6.03.02
The longitudinal bunch profile monitor needs turn-by-turn capability based on a single bunch in the fully filled bunch train to allow timing and energy adjustment for injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.9
6.03.02
The RCS shall contain a beam-based alignment system.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.10
6.03.02
The RCS shall contain a beam loss monitor system at select regions.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.3
6.03.02
The sextupoles shall be sorted into appropriate “families” and powered accordingly.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.4
6.03.02
There shall be dipole correctors capable of adjusting the beam orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.6
6.03.02
The quadrupoles shall generally be arranged in a conventional FODO structure.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.7
6.03.02
Each quadrupole strength needs to be capable of being changed independently by small amounts for beam-based alignment purposes.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.8
6.03.02
Sextupoles shall be sorted into “families” with the family structure dependent on the linear lattice configuration (betatron phase advance per FODO cell).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.9
6.03.02
The maximum integrated field strength of the FODO sextupoles needs to be sufficient to correct chromaticity to within 1 unit in both planes.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.10
6.03.02
Window-frame dipole corrector magnets capable of providing both horizontal and vertical dipole fields to correct the beam orbit in both transverse planes shall be placed adjacent to most of the quadrupoles.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.11
6.03.02
The strength of the window-frame dipole correctors needs to be chosen to correct for any source of orbit distortion and should have a margin for beam based diagnostic purpose.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-GUN-INST.4
6.03.04
To characterize and control the fresh bunches sent to the Mott polarimeter, the gun diagnostic beamline shall contain instrumentation to measure and control the profile, position, and charge of the beam.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-INST.5
6.03.04
The Diagnostic beamline section shall have one Beam Profile Monitor and Wien Filter and an electrostatic bender before the Mott polarimeter and Faraday Cup.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-GUN-INST.6
6.03.04
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

F-EIS-GUN-MAG.1
6.03.04
Following the DC gun, the electron bunch shall be deflected through a bending dipole into the Bunching section
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.2
6.03.04
2 solenoids shall be placed between the gun and the bending dipole into the bunching section capable of correcting the beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.3
6.03.04
Provision shall be made for an appropriate number of air cored steering coils between the Gun and bunching section to correct the electron beam position as required.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.4
6.03.04
A bending dipole shall follow the Gun and be able to bend the beam from the gun into the bunching section OR bend separate electron bunches into the separate diagnostic beam line.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.5
6.03.04
The bending dipole after the gun shall also have the capability to deflect the beam enough to allow a laser to illuminate the photocathode head on.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.6
6.03.04
A minimum of three solenoids shall be placed between the gun and the first bunching cavity to maintain the beam size for 5–10 nC bunches
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.7
6.03.04
Short air core trim coils shall be used to correct beam position for energies greater than 100 keV
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.8
6.03.04
The Diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-VAC.3
6.03.04
The Laser section shall be independent from the Gun\diagnostic section vacuum.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN.3x
6.03.03
The low energy transfer line shall have an additional branch between the Gun and the Bunching section which can transfer individual electron bunches into the diagnostic beamline section.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.4x
6.03.03
The low energy transfer line shall have a laser port between the Gun and the Bunching section which will allow an optical path for the laser to illuminate the cathode face of the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.6x
6.03.04
The gun shall have steering coils to direct the liberated electrons (These can be reused from the existing Gun system.)
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-HETL-ESR-INJ.1
6.03.03
The transferred beam shall meet all the requirements of the circulating beam, for all operational modes of the ESR as set forth in [5.9].
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-INST-BPM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed Beam Position Monitors at the quadrupoles and at the entry and exit of a number of the dipoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-IC.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain FCT and an Integrating Current Transformer before the ESR injection septum.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-PM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed YAG\OTR at the entry and exit of a number of the diploes and quadrupoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-POL.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a system to measure the beam polarization.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-BUMP.1
6.03.03
ESR injection shall have three fast bump magnets to direct the bunches from the HETL into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker of the ESR injector system shall operate in unison with a septum magnet which can direct the beam into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-SLINE-FKICK.1
6.03.03
The ESR injection system shall have a fast strip line kicker with a rise time of 2nsecs .
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.1
6.03.03
The High Energy Transfer Line shall match the beam parameters between the extraction point of the RCS and injection point of the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.2
6.03.03
The extraction into the required High Energy transfer line shall match the ESR bunch spacing and spin pattern.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.3
6.03.03
The High Energy Transfer Line shall be spin transparent.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.4
6.03.03
The ESR extraction system shall have another three bump magnets, its own septum magnet and use the strip line injection kicker to extract and replace the circulating bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BLM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be a bunch length monitor(BLM) at the exit of the 3rd harmonic buncher cavity to measure bunch compression during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam position monitor (BPM) at the entry to the 1st harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section a beam position monitor (BPM) at the entry and exit of the 2nd harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.3
6.03.04
To characterize the beam as it exits the buncher section, beam position monitor(BPM) at the exit of the 3rd harmonic buncher cavity to measure beam position during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-EM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be an emittance monitor(EM), at the exit of the 3rd harmonic buncher cavity to measure beam position, the beam emittance during commissioning.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-EM.01
6.03.04.02.06
Emittances shall be measured using a profile monitor and a dedicated upstream quadrupole configured to measure H, V, and skew profiles.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.03
6.03.04.02.06
The EM shall be able to measure the expected normalized emittance of 40 um
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.02
6.03.04.02.06
Before the 400 MeV beam goes into the spin rotator, the emittance shall be measured by a quad scan
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.04
6.03.04.02.06
Beam emittance shall be measured in the low energy diagnostics beamline using a slit scanner and profile monitor
05/16/2025
On Hold
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.1
6.03.04
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), at the entry and exit of the 2nd harmonic buncher cavity to measure charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.2
6.03.04
To characterize the beam as it exits the buncher section, an integrating current transformer(ICT) at the exit of the 3rd harmonic buncher cavity to measure the bunch charge during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-LM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam loss monitor (BLM) at the entry to the 1st harmonic buncher cavity to measure beam loss
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a transverse profile monitor(TPM) at the entry to the 1st harmonic buncher cavity to measure the charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section there shall be a transverse profile monitor(TPM) at the entry and exit of the 2nd harmonic buncher cavity to measure the bunch profille.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.3
6.03.04
To characterize the beam as it exits the buncher section, transverse profile monitor(TPM) at the exit of the 3rd harmonic buncher cavity the bunch profile during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-MAG-SOL.4
6.03.04
The solenoidal field shall extend to also contain the 1st RF tank of the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-CAV.1
6.08
The LINAC TWP cavities shall be constant gradient cavities
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-INST-CM.1
6.03.04
Bunch charge measurements shall be performed at multiple locations through the LINAC.
05/16/2025
In Process
FALSE

F-EIS-LINAC-INST-PM.1
6.03.04
To measure the beam profile in the LINAC section there shall be a plunging YAG/OTR transverse profile monitor between the 1st and 2nd accelerating cells.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-QUAD.3
6.03.04
A drift space with quadrupole triplets shall be placed between each TWP structure to tune the bunch beta function through the LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.3
6.03.04
Between each S-band LINAC section there shall be at least two window frame steering magnets.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.4
6.03.04
Additionally, window frame steering magnets will be placed at the entry and exit of each accelerating structure to position the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.1
6.03.04
Following the Zigzag there shall be a de-chirp cavity to linearize and reduce the energy spread of the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.1
6.03.04
A longitudinal matching section shall follow the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC.4
6.03.04
The 1st part of the S-band LINAC shall be contained inside a continuous solenoidal field to maintain the bunch envelope into the LINAC (see bunching section solenoid).
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.2
6.03.03
The fast kicker magnet shall follow the rise and fall of the amplitude of the RF sinusoidal functions
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST-BPM.1
6.03.03
To control the beam through the Spin Rotator section there shall be a Beam Position Monitors placed throughout the spin rotator as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST.1
6.03.03
To measure and control the beam in the medium energy 400 MeV transfer line there shall be sufficient beam position monitors for orbit control, transverse profile monitors, and bunch charge monitors as required.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

F-EIS-METL-MAG-DIP.1
6.03.03
At the entry to the spin rotator section before the spin rotator solenoid there shall be a number of bending dipole to rotate the polarization spin from the Longitudinal direction into the transverse X direction.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-DIP.2
6.03.03
After the exit of spin rotator solenoid, there shall be a number of bending dipoles to close the geometry and direct the beam into the medium energy 400[MeV] transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.5
6.03.03
The spin rotator quadrupoles after the Spin rotator solenoid shall be able to match the beam beta functions βx and βy to that required for entry into the 400MeV transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.6
6.03.03
The spin rotator exit quadrupoles shall have at least 2 families this is required to control the electron beam optics as needed.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.7
6.03.03
The spin rotator solenoid shall rotate the electron beam spin from the X axis to the vertical y-axis before it enters the medium [400MeV] transport line to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.8
6.03.03
The spin rotator solenoid shall have an integrated gradient of 2.2 [T.m] required to rotate the spin from the horizontal axis to the vertical axis.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.1
6.03.03
The bump magnets shall have a rise and time consistent with the requirements of the circulating bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.2
6.03.03
The Pulsed bump magnets shall be able to create a closed orbit path passing close to the Septum and maintain it during each injection cycle (100-150 Hz).
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.6
6.03.03
Each train of four bunches shall be injected into neighboring RF buckets to facilitate bunch merges.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.7
6.03.03
The injection system shall be capable of maintaining the small spacing required by the injected bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.11
6.03.03
The injection system into the RCS shall be capable of injecting successive bunches into the RCS to create a bunch train with four bunches each circulating in the RCS ready to be merged.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.12
6.03.03
The RCS shall be capable of merging each train of 4 bunches into a larger single bunch to create larger single circulating bunche in the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.2
6.03.03
The Medium energy transfer line shall contain 3 sections: 1. Spin rotation section, 2. The main transfer line, 3. The Injector system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.3
6.03.03
There will be number of corrector Quadrupoles after the Pre-Injector longitudinal matching and before the spin rotator to provide beam matching into the Spin Rotator.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.4
6.03.03
The medium energy 400 MeV transfer line shall be able to transport the spin reoriented beam from the spin rotator to the RCS injection system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.5
6.03.03
The medium energy 400 MeV transfer line will maintain the spin direction of the beam along the entire transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.6
6.03.03
The spin rotator shall ensure the spin direction of the electron bunches are rotated from the longitudinal Z axis to the vertical Y axis.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH-INST.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be beam position monitor (BPM), and a transverse profile monitor at the entry to the buncher cavity to measure beam loss, position, and charge.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.2
6.06.03
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), beam position monitors and transverse profile monitors
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.3
6.06.03
To characterize the beam as it exits the buncher section, there shall be an emittance measurement including slit and beam viewer, an integrating current transformer, beam position monitor, charge and compression during commissioning.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-MAG.1
6.03.04
A seris of the solenoid magnets shall placed between the Wien filter up to the beam energy of 10 MeV.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-MAG.2
6.03.04
The Solenoid has the Bz.l total equal to zero. Bz is free to tune.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-MAG.3
6.03.04
Air core mangets shall placed closeby with each solenoid to correct beam orbit
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.2
6.08
The bunching section shall generate sufficient compression to compress the bunch length to that required by [5.9].
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.3
6.08
The bunchers rf voltage and phase will be synchronized so that the passing electron bunches meet the required beam characteristics at the end of the buncher section.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-LINAC-VAC.1
6.03.04
The LINAC section shall contain enough strategically located Vacuum gate valves, to allow access to the vacuum volume as needed.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.1
6.03.03
The LTR transfer line shall terminate with an injection system capable of transferring the beam into the RCS for all the operating energies and conditions specified in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.3
6.03.03
The vertically spin polarized electron bunch patterns generated by the pre-injector shall be transferred into the RCS unaltered.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.1
6.08
There shall be a special RF kicker to kick the injected beam into neighboring RF buckets without disturbing the 8 circulating bunches.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ.1
6.03.04
The EIS Pre-Injector shall consist of 3 sub-systems: 1. An electron gun section, followed by 2. A low energy transfer line and bunching section, followed by 3. A LINAC section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-INST.1
6.03.04
EIS shall have all the beam instrumentation necessary to deliver the operational parameters set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-HETL-INST-BPM-ELEC.01
6.03.03.04.01
The BPM single bunch measurement resolution for a (1 - 4 nC) pilot bunch shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.02
6.03.03.04.01
The BPM single bunch measurement resolution for (5.5 - 28 nC) bunches shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.03
6.03.03.04.01
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.04
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used to measure the transport lattice.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.01
6.03.03.04.01
The BPM Pickup alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.02
6.03.03.04.01
The BPM Pickup shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.04
6.03.03.04.01
The BPM Pickups shall be located by the dipole correctors at every second quadrupole.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM-ELEC.01
6.03.03.04.01
For a (1 nC) pilot bunch, the BPM single bunch measurement resolution shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.02
6.03.03.04.01
For (5.5 - 10 nC) bunches, the BPM single bunch measurement resolution shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.03
6.03.03.04.01
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.04
6.03.03.04.01
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.01
6.03.03.04.01
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.02
6.03.03.04.01
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.04
6.03.03.04.01
The location of the BPM Pickups shall be TBD
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.01
6.03.02.05.04
A synchrotron light monitor (SLM) shall be installed in the RCS ring downstream of an RCS dipole magnet
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.02
6.03.02.05.04
The location of the SLM light extraction port shall be- TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.03
6.03.02.05.04
The synchrotron light shall be transported from the RCS light extraction port to an optical table for detection.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.04
6.03.02.05.04
The synchrotron light optical table shall have a streak camera and gated camera shall be installed.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.05
6.03.02.05.04
The SLM shall be able to make Turn-by-turn measurements using gated cameras to provide measurements of; the injection matching parameters and the beam position stability parameters during acceleration. TBD -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.06
6.03.02.05.04
The SLM shall be used to provide horizontal and vertical transverse profile measurements on bunches with charges > 6nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.07
6.03.02.05.04
The SLM horizontal and vertical transverse profile measurements shall be measured with a resolution in both planes of 0.1 mm
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.08
6.03.02.05.04
The SLM shall be used to provide longitudinal profile measurements
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.09
6.03.02.05.04
A dual sweep streak camera shall be used to provide measurements of the bunch length and longitudinal profiles
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.10
6.03.02.05.04
The dual sweep streak camera shall have a resolution of <5 ps
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.11
6.03.02.05.04
The profile measurements shall be used, together with modeled or measured beam optics to infer the beam emittances and energy spread.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.12
6.03.02.05.04
The Vertical emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.6 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.13
6.03.02.05.04
The Horizontal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 10 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.14
6.03.02.05.04
The Longitudinal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.00001 eV-s
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.15
6.03.02.05.04
The Energy spread measurement, for bunch charges > 6nC, shall be measured with a precision of 0.0001 dp/p
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.01
6.04.06.02
A bunch pattern monitor shall be installed in the ESR to measure indiviual bunch charge with an accuracy 1 %
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.02
6.04.06.02
The Bunch pattern monitor shall be capable of measuring Bunch patterns ranging from a single bunch, to a filled ring with 1,160 bunches
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.01
6.04.06.05
BLM shall be needed to needed to protect sensitive equipment.
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.02
6.04.06.05
The number of BLM installed in the ESR shall be TBD ea
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.03
6.04.06.05
BLM shall be installed at the following locations in the ESR TBD
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.04
6.04.06.05
The sensitivity of the BLM detectors shall be TBD units?
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.05
6.04.06.05
Where possible existing RHIC BLM's can be relocated to identify ESR & HSR losses
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.06
6.04.06.05
The response time from loss detection to abort shall be TBD us
05/16/2025
In Process
FALSE

P-ESR-INST-BPM-ELEC.01
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following capabilities defined for the low intensity pilot injection energies and high intensity collision energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following time resolutions for data refresh defined for the beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.03
6.04.06.01
The ESR BPM Electronics shall have the following time resolutions for data logging defined for the beam energies:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.04
6.04.06.01
The ESR BPM Electronics shall have the following measurement resolutions defined for beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.05
6.04.06.01
The ESR BPM Electronics shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.06
6.04.06.01
The ESR BPM Electronics shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-PU.01
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall provide dual plane (horizontal and vertical) beam positional measurements.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) shall be positioned in the following locations approved by physics as defined in the lattice:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.03
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) mechanical and electrical center in the locations identified shall be:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.04
6.04.06.01
The ESR Beam Position Monitor Pick-Ups housing shall have a +/- 10 (mrad) corresponding to +/- 0.6 (degree) roll tolerance with regards to BPM measurements in respect to the vacuum chamber.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.05
6.04.06.01
The ESR Beam Position Monitor Pick-Ups design shall be less than or equal to the allocated impedance and is within the accepted overall ESR impedance budget approved by physics. (replace with loss factor)
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.06
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall fulfill resolution requirements over the horizontal and vertical beam position range with respect to its fiducials of +/- 3 (mm).
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.07
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to ensure the maximum temperatures of the components (due to heating by the beam) are acceptable for reliability and operations of the EIC over the planned operational life of 20 (yrs).
09/15/2025
In Process
FALSE

P-ESR-INST-BPM-PU.09
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to be baked to 250 °C for UHV processing.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.10
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.11
6.04.06.01
The ESR BPM Pickup shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/30/2025
In Process
FALSE

P-ESR-INST-BPM-PU.12
6.04.06.01
The ESR Beam Position Monitor Button configuration will be mirror symmetric with respect to the mid-and center planes. Deviation from symmetry shall be such that corresponding BPM reading errors are less then 20 microns.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.13
6.04.06.01
The ESR Beam Position Monitor Pick-Ups symmetrical configuration (postion between the four buttons and the relative to the fiducials on top of the button) shall be stable under the inference of the expected operational thermal changes to the extent that corresponding changes in the bpm reading deviate less than 20 µm.
07/25/2025
Approved
FALSE

P-ESR-INST-DCCT.01
6.04.06.02
A DCCT shall measure the average beam current in the ESR.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.02
6.04.06.02
The measurement resolution averaged over 1 sec shall be < 5 uA
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.03
6.04.06.02
The DCCT beamline device impedance shall be approved by beam physics.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.04
6.04.06.02
Measurement drift tolerance (thermal effects) shall be ≤ 1 uA/K
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.05
6.04.06.02
The DCCT sensor in the ring shall operate in the temperature range of 15 to 35 degrees C
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.06
6.04.06.02
The range of average beam current to be measured shall be 0.156x10-3 to 2.5 A
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.07
6.04.06.02
The DCCT system shall have a remote controlled self calibration system
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.08
6.04.06.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.09
6.04.06.02
The measured average current shall be provided to users at a rate of 10 Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.10
6.04.06.02
The measured average current shall be archived at a rate of 10 Hz Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.11
6.04.06.02
The DCCT sensor assembly in the ring shall be radiation resistant
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.01
6.04.06.03
The requirements for longitudinal feedback are ??? TBD
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.02
6.04.06.03
The Longitudinal feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.01
6.04.06.04
The ESR shall have two synchrotron light monitors (SLM) and one X-ray pin hole monitor
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.02
6.04.06.04
The longitudinal bunch profile monitor shall have a turn-by-turn capability based on a single bunch in the fully filled bunch train.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.03
6.04.06.04
TThe SLM systems shall measure the crabbing angle, longitudinal bunch parameters, H & V beam size and global coupling.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.04
6.04.06.04
The SLM shall be able to measure a crabbing angle of 12.5 mrad with accuracy of 10 %
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.05
6.04.06.04
The SLM shall be able to measure the Longitudinal bunch parameters with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.06
6.04.06.04
The SLM shall be able to measure the H & V beam size with accuracy of H=?? V=?? units
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.07
6.04.06.04
The SLM shall be able to measure the Global coupling with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.08
6.04.06.04
One SLM port shall be located downstream of a dipole in an appropriate location in the ESR, exact location not critical.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.09
6.04.06.04
The second SLM port shall be located in a complimentary location in the lattice to ensure all the necessary SLM measurements can be made. TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.10
6.04.06.04
The SLM light extraction port mirrors shall be good quality, having a surface finish better than 1/10 Lambda
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.11
6.04.06.04
The SLM light extraction port mirrors shall be water cooled to avoid image distortion.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.12
6.04.06.04
There shall be an enclosed SL transport from the light extraction port to the SLM optical lab rooms. Length to be determined by the distance to optical lab room, should be minimized to reduce vibration problems.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.13
6.04.06.04
The locations of the SLM optical lab rooms shall be TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.14
6.04.06.04
The double-slit interferometer method shall be used to measure transverse beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.15
6.04.06.04
The standard transverse resolution of an SLM using visible light shall be ~60 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.16
6.04.06.04
The resolution using the double-slit method shall equal to 10 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.17
6.04.06.04
A streak camera shall be used to measure the bunch longitudinal profiles
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.18
6.04.06.04
A position sensitive photo-diode will provide photon beam centroid information which shall supplement the orbit stability measurements by the BPMs
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.19
6.04.06.04
A GigE CCD/CMOS camera, externally triggerable with exposure times ranging from 10 nsec to 5 sec, shall be used to image the visible radiation
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.20
6.04.06.04
A commercially available gated camera with gate width of <2 nsec (compared to a minimum bunch spacing of 10 nsec) shall be used to detect injection oscillations and for beam studies.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.21
6.04.06.04
The location of the X-ray pinhole monitoring system shall be TBD
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.22
6.04.06.04
The target resolution of the X-ray pin hole monitoring system shall be ~ 5 um (or as best that can be achieved with the machine parameters and commercial equipment) 5 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.23
6.04.06.04
The X-ray pin hole monitor shall provide independent measurement of the energy spread and horizontal/vertical emittance. H=V=15.4 nm
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.24
6.04.06.04
The X-ray pinhole photon beamline shall be equipped with gated cameras that will be employed to provide high resolution turn-by-turn profile measurements
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.25
6.04.06.04
A pinhole assembly including tungsten slits shall provide sufficient resolution to precisely measure the beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.26
6.04.06.04
Several different size pinholes sizes shall be incorporated to allow easy alignment and measurements at different beam currents and energies.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.01
6.04.06.03
Stripline kickers (H & V) shall be used to excite the beam so tunes can be measured using turn-by-turn BPM data.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.02
6.04.06.03
The magnitude of the kick required for the horizontal kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.03
6.04.06.03
The magnitude of the kick required for the vertical kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.04
6.04.06.03
The kicker waveform (risetime and shape) requirements shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.05
6.04.06.03
The location of the tune meter kicker striplines in the ESR shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.06
6.04.06.03
The impedance of the kicker beamline device shall be approved by beam Physics.
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.01
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.03
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.02
6.04.06.03
The transverse feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSSLFB.01
6.04.06.03
The transverse slow feedback system bandwidth shall bs 10 Hz
05/16/2025
In Process
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.2
6.03.04
At the end of the Zigzag there shall be a diagnostic section (details TBD) to measure the bunch length and dP/P.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-DIP.1
6.03.04
The ZigZag section shall consist of a number of dipoles separated by drift spaces in a R56 configuration to increase the bunch length to 40ps.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-QUAD.1
6.03.04
The ZigZag section shall consist of a number of Quadrapoles to control the beam dispersion through the zigzag.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.2
6.03.04
The longitudinal matching section shall consist of a so-called Zigzag section followed by a de-chirp cavity which will stretch the bunch length to 40 ps, reduce the energy spread, and generate a longitudinal phase space rotation of the bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.3
6.03.04
At the Zigzag exit, the electron beam’s average spin orientation shall be longitudinal in the direction of beam travel.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.1
6.03.03
The fast kicker magnet shall be capable of deflecting the electron beam from the RCS to counter the RF kick.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.4
6.03.03
The spin rotator entry quadrupole shall have at least 2 families this is needed to control the electron beam optics as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.1
6.03.03
The Medium energy transfer line shall transfer the beam from the pre-injector longitudinal matching section to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH-RF.1
6.08
one 197 MHz buncher cavity shall be used for providing bunch chirp
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.1
6.03.03
The pre-injector LEBT low energy RF section shall transfer the electron beam from the gun to the linac section. shall provide bunching and initial acceleration to each 1 nC bunch
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.4
6.08
The Pre-Injector layout shall accommodate all RF cavities and allow enough room for other Pre-Injector components.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-GUN.2
6.03.04
The pre-injector electron gun shall produce all the bunch patterns required to deliver the ESR beam requirements set forth in [5.9].
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.21
6.03.04
The diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.1
6.03.03
The pre-injector shall have a low energy transfer line from the gun into the beam compression "Bunching" section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.6
6.03.04
Following the gun, there shall be multiple groups of magnets required to control the electron beam.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.7
6.03.04
To characterize and control the fresh bunches the low energy transfer line from the Gun to the Buncher shall contain a plunging transverse profile monitor, a bunch charge monitor, beam loss monitors, and beam position monitors
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-TLINE-MEBT-MAG-QUAD.1
6.03.03
The corrector Quadrupoles shall be able to suppress the βx and βy along the transfer line to levels consistent with those required ate the RCS injection kicker.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-SEP.1
6.03.03
The septum magnet shall be capable of deflecting the incoming electron beam into the RCS and shielding the circulating beam already in the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.2
6.03.03
The injection system shall inject the beam at Need update
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.4
6.03.03
The injection system shall be able to inject one bunch per injection kick using RF and magnetic kickers to build up a total of 8 bunches from 4 kicks to the RF and kickers.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.5
6.03.03
The injection system shall ensure the bunch emittance shall match the requirements of the RCS RF system and such, to avoid collective instabilities and to stay within the off-momentum aperture.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.9
6.03.03
The injection system shall contain 3 bump magnets to locally bump the RCS circulating beam close to the injection septum.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.10
6.03.03
The RCS injection system shall contain an RF kicker and a pulsed magnet followed by a septum magnet to redirect the beam into the RCS closed orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.11
6.03.03
The magnetic field of the injection system pulsed magnet shall follow the rise time of the power amplifiers which drive the RF kickers..
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.2
6.08
The special kicker shall consist of an RF harmonic kicker with fundamental frequency of 1/4 of the main RCS RF cavity or compatible equivalent alternative.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.3
6.08
The special kicker shall have a rise and fall time that matches the RF bucket size.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.4
6.08
The special kicker shall have a peak power necessary to generate a kick to inject the bunch into the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.5
6.08
The special kicker shall have a macro pulse with a flattop that is greater than the time between the LINAC bunches and shall have a rise and fall time less than 1 RCS turn.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.6
6.08
The special kicker shall be able to repeat at the LINAC pulse rate.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT.28
6.03.03
The LTR transfer line shall have several FODO quadrupoles to control the beta function along the transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ.3
6.03.04
The EIS Pre-Injector shall create bunches which meet the requirements set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-RCS-MAG-QUAD.5
6.03.02
The quadrupoles shall be individually powered with low supplementary current/voltage power supplies for beam-based alignment purposes.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.7
6.03.02
The RCS straight sections shall have the appropirate number of defocusing and focusing quadrupole families per straight section.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.9
6.03.02
The non-colliding straights will have different scheme.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.14
6.03.02
The main arc quadrupoles shall be powered by a total of 2 power circuits 1 for focusing the other defocusing.
05/16/2025
In Process
FALSE

F-EIS-RCS-MAG.15
6.03.02
The quadrupoles in both straight sections shall need a total of 6 power circuits to power all six families of quadrupoles in both straights. (straights are optically identical)
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.18
6.03.02
The RCS magnets shall be fed by a system of power supplies matched in voltage and maximum current to the specifications and requirements of the respective magnets.
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-BUMP.1
6.03.03
the RCS extraction system shall have three fast bump magnets to direct the bunches to the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-FKICK.1
6.03.03
RCS extraction shall be facilitated with a fast kicker having a rise time of 2 micro-secs
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker shall operate in unison with a septum magnet which can direct the beam into the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.1
6.03.03
The beam injection of the electron bunches from the RCS into the ESR ring shall take place in the 12 o’clock straight section.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.2
6.03.03
There will be two electron bunches circulating in the RCS at extraction, these shall be injected into the High Energy Transfer Line which connects the RCS to the ESR.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.1
6.08
The RF system shall Provide a maximum RF voltage of 60MV to accelerate the beam.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.2
6.08
The total RF power provided by the RF amplifiers shall be able to compensate for all additional losses created by the stored electron beam in addition to the acceleration and synchrotron losses.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.3
6.08
The RF system shall Provide sufficient gradient to allow installation of all necessary RF modules in the limited space in IR 10.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.4
6.08
The RF system shall be able to accommodate 4 circulating bunches in one trains of 4 bunches.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.5
6.08
The RF system shall be able to merge the one train of 4 bunches into two larger separate circulating bunches then merge these two large bunches into a single larger circulating bunch.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.6
6.08
The RF system shall be able to accelerate final large, merged bunch to the operating energies needed by the ESR as set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.7
6.03.02
The RF system controls shall be designed to handle the transient beam loading for all bunch structures.
05/16/2025
In Process
FALSE

F-EIS-RCS-VAC.1
6.03.02
The vacuum chamber shall provide sufficient horizontal and vertical aperture to accommodate a beam which is 5 σ larger than the largest sigma beam size determined by the injected RMS emittance.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.2
6.03.02
The average dynamic pressure around the ring shall be < 5e-8[Torr] after 1 year of operation.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.3
6.03.02
The impedance of the entire RCS vacuum system shall allow for the bunch intensities, beam currents, and bunch numbers contained in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.09
6.03.02.04
The vacuum chamber shall be capable of absorbing and carrying away the eddy current power.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.4
6.03.02
The vacuum chamber and all its components shall be designed to withstand the total synchrotron radiation loads seen in operation.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-VAC.08
6.03.02.04
The vacuum chamber shall be capable of absorb synchrotron radiation and carrying away the absorbed power.
05/16/2025
Approved
FALSE

F-EIS-RCS.1
6.03.02
The RCS shall consist of two parts 1. The main RCS Ring, and 2. The High energy transfer line terminating with the ESR injection system
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.2
6.03.03
The RCS shall be capable of accepting the bunches and matching the bunch parameters as injected by the BAR into the LTR transfer line.
05/16/2025
In Process
FALSE

F-EIS-RCS.3
6.03.02
After bunch injection into the RCS, the RCS shall merge the injected bunches into two bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.4
6.03.02
After bunch injection the RCS shall be able to accelerate the single bunch to the final desired energy set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS.5
6.03.02
The RCS needs to accelerate to the top possible energy in a time interval consistent with the parameters set forth in [5.9] at approximately 100 msecs for 18 GeV.
05/16/2025
In Process
FALSE

F-EIS-RCS.6
6.03.03
The RCS shall be capable of kicking the accelerated bunches into the RTE transfer line to the ESR.
05/16/2025
In Process
FALSE

F-EIS-RCS.7
6.03.02
RCS will need to increase the vertical emittance to match the ESR vertical emittance.
05/16/2025
In Process
FALSE

F-EIS-RCS.8
6.03.02
The RCS shall have a racetrack design with 160 arc FODO cells, bending radius of 91.67 m and two 86.624 m straight sections made up of 8 FODO cells with a total circumference of 1.421 km
05/16/2025
In Process
FALSE

F-EIS-RCS.15
6.03.02
The RCS lattice shall contain provisions for correctors such as dipole correctors etc., as needed.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-TLINE-GUN-Diagnostic.1
6.03.04
The Pre-injector separate diagnostic beamline section shall have 3 branches one with Faraday cup, one port containing a connection to the cathode Laser and a line to a low energy beam dump.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.1
6.03.04
The instrumentation in the diagnostic beamline to the low energy beam dump shall have the capability to measure beam position, profile, bunch charge
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.4
6.03.04
The Faraday cup shall be able to measure the charge of the electron bunches from the gun.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-LASER-INST.1
6.03.04
There shall be instrumentation capable of measuring the position and profile of the laser beam on the cathode.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-LASER.1
6.03.04
The laser beam shall illuminate the cathode perpendicular to the cathode face
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.1
6.03.04
The beam tube and flange sizes shall be appropriate to transport polarized e-beam between the e-source and the diagnostic beam line polarimeter chamber.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.2
6.03.04
Vacuum system shall be compatible with UHV requirements.
05/16/2025
Not Applicable
FALSE

F-EIS-TLINE-SPIN.INST.1
6.03.03
Profile monitor, BPM are placed at before, in between and after two Wien filters
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.1
6.03.03
Between the dipole chamber and the bunching section, two Wien filters shall be used as spin rotator to rotate the spin direction from longitudinal to vertical.
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.2
6.03.03
triplets focusing are used in between the two Wien filters to maintain the beam envolop
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.3
6.03.03
Quadpole single let and double let are used before and after Wien to compensate the quadropole components from the Wien entrance and exit
05/16/2025
In Process
FALSE

F-EIS-VAC.1
6.03.04
The EIS vacuum system shall meet UHV standards at a minimum (Ref vacuum spec?)
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.07
6.03.02.04
On 15 m on each side (or one vacuum section) of the SRF cavities the vacuum system shall be processed to class ISO 5.
05/16/2025
Approved
FALSE

F-EIS-VAC.2
6.03.04
The impedance of the entire EIS vacuum system, including the transport lines, shall allow for the bunch intensities, beam currents, and bunch numbers contained in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.01
6.03.03.03
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.03
6.03.03.03
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.01
6.03.03.03
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.03
6.03.03.03
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-VAC.3
6.03.04
The size, location and type of vacuum pumps shall be chosen to meet the required vacuum levels during operation
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-VAC.4
6.03.04
Appropriate vacuum gauging shall be supplied in each vacuum sector to monitor the required vacuum levels
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

G-EIS.4x
6.07.02
The EIS shall have a control system which can operate the EIS consistent will the overall control of the other EIC system's and to ensure the ESR meets all the Physics requirements needed to deliver the physics goals of the EIC.
05/16/2025
Not Applicable
FALSE

F-EIS-CNTRL.1
6.07.02
The EIS control system shall facilitate all IR global control requirements.
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

F-EIS-CNTRL.2
6.07.02
The EIS control system shall facilitate all network, relational database and data archiving required.
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

F-EIS-CNTRL.3
6.07.02
The control system shall facilitate all machine protection systems required
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

F-EIS-CNTRL.5
6.07.02
The EIS control system shall facilitate fast feedback integration systems required.
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

F-EIS-CNTRL.4
6.07.02
The EIS control system shall facilitate all EIC machine timing required.
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT-INJ.01
6.07.02
Placeholder , Tuning requirements Should be listed here and/or under transfer lines in 6.03 shall be tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

F-EIS-CNTRL.6
6.07.02
The EIS control system shall facilitate all physics application support required.
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

G-EIS.5
6.03
The EIS pre-injector shall provide an electron beam to the ESR having a vertical beam emittance which is compatible with operation of the ESR.
05/16/2025
Approved
FALSE

F-EIS- PREINJ-LINAC-MAG.1
6.03.04
A Quadrupole triplet shall be installed between each accelerating structure in the LINAC to control the beam beta function and dispersion.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.2
6.03.04
The LINAC Quadrupole triplets shall be optimized to control beams with high RCS injection energies ~ 400[MeV].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.3
6.03.04
In addition to the Quadrupole triplets X Y steering coils shall be installed between each 2.856[GHz] accelerator structure to control the beam beta function and dispersion in the LINAC.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.4
6.03.04
A LINAC XY steering coils shall be optimized to control beams which have low RCS injection energies < < 400[MeV]
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.1
6.03.04
The Pre-Injector S-band LINAC shall be able to accelerate all electron bunches up to the energy's required by [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.2
6.03.04
The Pre-Injector LINAC frequency shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.3
6.03.04
The Pre-Injector LINAC rep-rate shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.1
6.03.02
The instrumentation system shall contain a Beam Position Monitor system consisting of dual-plane Beam Position Monitors adjacent to each quadrupole.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.2
6.03.02
Select Beam Position Monitors in the injection region shall have turn-by-turn orbit measurement capability based on a single, remotely selectable bunch out of the fully filled bunch train to enable injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.3
6.03.02
The instrumentation system shall include a beam current monitor to measure average beam current.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.4
6.03.02
The instrumentation system shall include a system to measure individual bunch charges and bunch pattern.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.5
6.03.02
The instrumentation system shall include a system to measure transverse bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.6
6.03.02
The instrumentation system shall include a system to measure longitudinal bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.7
6.03.02
The instrumentation system shall contain a betatron and synchrotron tune monitors.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.8
6.03.02
The longitudinal bunch profile monitor needs turn-by-turn capability based on a single bunch in the fully filled bunch train to allow timing and energy adjustment for injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.9
6.03.02
The RCS shall contain a beam-based alignment system.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.10
6.03.02
The RCS shall contain a beam loss monitor system at select regions.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.3
6.03.02
The sextupoles shall be sorted into appropriate “families” and powered accordingly.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.4
6.03.02
There shall be dipole correctors capable of adjusting the beam orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.6
6.03.02
The quadrupoles shall generally be arranged in a conventional FODO structure.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.7
6.03.02
Each quadrupole strength needs to be capable of being changed independently by small amounts for beam-based alignment purposes.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.8
6.03.02
Sextupoles shall be sorted into “families” with the family structure dependent on the linear lattice configuration (betatron phase advance per FODO cell).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.9
6.03.02
The maximum integrated field strength of the FODO sextupoles needs to be sufficient to correct chromaticity to within 1 unit in both planes.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.10
6.03.02
Window-frame dipole corrector magnets capable of providing both horizontal and vertical dipole fields to correct the beam orbit in both transverse planes shall be placed adjacent to most of the quadrupoles.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.11
6.03.02
The strength of the window-frame dipole correctors needs to be chosen to correct for any source of orbit distortion and should have a margin for beam based diagnostic purpose.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-GUN-INST.4
6.03.04
To characterize and control the fresh bunches sent to the Mott polarimeter, the gun diagnostic beamline shall contain instrumentation to measure and control the profile, position, and charge of the beam.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-INST.5
6.03.04
The Diagnostic beamline section shall have one Beam Profile Monitor and Wien Filter and an electrostatic bender before the Mott polarimeter and Faraday Cup.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-GUN-INST.6
6.03.04
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

F-EIS-GUN-MAG.1
6.03.04
Following the DC gun, the electron bunch shall be deflected through a bending dipole into the Bunching section
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.2
6.03.04
2 solenoids shall be placed between the gun and the bending dipole into the bunching section capable of correcting the beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.3
6.03.04
Provision shall be made for an appropriate number of air cored steering coils between the Gun and bunching section to correct the electron beam position as required.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.4
6.03.04
A bending dipole shall follow the Gun and be able to bend the beam from the gun into the bunching section OR bend separate electron bunches into the separate diagnostic beam line.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.5
6.03.04
The bending dipole after the gun shall also have the capability to deflect the beam enough to allow a laser to illuminate the photocathode head on.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.6
6.03.04
A minimum of three solenoids shall be placed between the gun and the first bunching cavity to maintain the beam size for 5–10 nC bunches
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.7
6.03.04
Short air core trim coils shall be used to correct beam position for energies greater than 100 keV
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.8
6.03.04
The Diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-VAC.3
6.03.04
The Laser section shall be independent from the Gun\diagnostic section vacuum.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN.3x
6.03.03
The low energy transfer line shall have an additional branch between the Gun and the Bunching section which can transfer individual electron bunches into the diagnostic beamline section.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.4x
6.03.03
The low energy transfer line shall have a laser port between the Gun and the Bunching section which will allow an optical path for the laser to illuminate the cathode face of the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.6x
6.03.04
The gun shall have steering coils to direct the liberated electrons (These can be reused from the existing Gun system.)
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-HETL-ESR-INJ.1
6.03.03
The transferred beam shall meet all the requirements of the circulating beam, for all operational modes of the ESR as set forth in [5.9].
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-INST-BPM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed Beam Position Monitors at the quadrupoles and at the entry and exit of a number of the dipoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-IC.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain FCT and an Integrating Current Transformer before the ESR injection septum.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-PM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed YAG\OTR at the entry and exit of a number of the diploes and quadrupoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-POL.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a system to measure the beam polarization.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-BUMP.1
6.03.03
ESR injection shall have three fast bump magnets to direct the bunches from the HETL into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker of the ESR injector system shall operate in unison with a septum magnet which can direct the beam into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-SLINE-FKICK.1
6.03.03
The ESR injection system shall have a fast strip line kicker with a rise time of 2nsecs .
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.1
6.03.03
The High Energy Transfer Line shall match the beam parameters between the extraction point of the RCS and injection point of the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.2
6.03.03
The extraction into the required High Energy transfer line shall match the ESR bunch spacing and spin pattern.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.3
6.03.03
The High Energy Transfer Line shall be spin transparent.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.4
6.03.03
The ESR extraction system shall have another three bump magnets, its own septum magnet and use the strip line injection kicker to extract and replace the circulating bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BLM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be a bunch length monitor(BLM) at the exit of the 3rd harmonic buncher cavity to measure bunch compression during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam position monitor (BPM) at the entry to the 1st harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section a beam position monitor (BPM) at the entry and exit of the 2nd harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.3
6.03.04
To characterize the beam as it exits the buncher section, beam position monitor(BPM) at the exit of the 3rd harmonic buncher cavity to measure beam position during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-EM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be an emittance monitor(EM), at the exit of the 3rd harmonic buncher cavity to measure beam position, the beam emittance during commissioning.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-EM.01
6.03.04.02.06
Emittances shall be measured using a profile monitor and a dedicated upstream quadrupole configured to measure H, V, and skew profiles.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.03
6.03.04.02.06
The EM shall be able to measure the expected normalized emittance of 40 um
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.02
6.03.04.02.06
Before the 400 MeV beam goes into the spin rotator, the emittance shall be measured by a quad scan
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.04
6.03.04.02.06
Beam emittance shall be measured in the low energy diagnostics beamline using a slit scanner and profile monitor
05/16/2025
On Hold
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.1
6.03.04
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), at the entry and exit of the 2nd harmonic buncher cavity to measure charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.2
6.03.04
To characterize the beam as it exits the buncher section, an integrating current transformer(ICT) at the exit of the 3rd harmonic buncher cavity to measure the bunch charge during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-LM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam loss monitor (BLM) at the entry to the 1st harmonic buncher cavity to measure beam loss
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a transverse profile monitor(TPM) at the entry to the 1st harmonic buncher cavity to measure the charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section there shall be a transverse profile monitor(TPM) at the entry and exit of the 2nd harmonic buncher cavity to measure the bunch profille.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.3
6.03.04
To characterize the beam as it exits the buncher section, transverse profile monitor(TPM) at the exit of the 3rd harmonic buncher cavity the bunch profile during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-MAG-SOL.4
6.03.04
The solenoidal field shall extend to also contain the 1st RF tank of the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-CAV.1
6.08
The LINAC TWP cavities shall be constant gradient cavities
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-INST-CM.1
6.03.04
Bunch charge measurements shall be performed at multiple locations through the LINAC.
05/16/2025
In Process
FALSE

F-EIS-LINAC-INST-PM.1
6.03.04
To measure the beam profile in the LINAC section there shall be a plunging YAG/OTR transverse profile monitor between the 1st and 2nd accelerating cells.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-QUAD.3
6.03.04
A drift space with quadrupole triplets shall be placed between each TWP structure to tune the bunch beta function through the LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.3
6.03.04
Between each S-band LINAC section there shall be at least two window frame steering magnets.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.4
6.03.04
Additionally, window frame steering magnets will be placed at the entry and exit of each accelerating structure to position the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.1
6.03.04
Following the Zigzag there shall be a de-chirp cavity to linearize and reduce the energy spread of the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.1
6.03.04
A longitudinal matching section shall follow the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC.4
6.03.04
The 1st part of the S-band LINAC shall be contained inside a continuous solenoidal field to maintain the bunch envelope into the LINAC (see bunching section solenoid).
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.2
6.03.03
The fast kicker magnet shall follow the rise and fall of the amplitude of the RF sinusoidal functions
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST-BPM.1
6.03.03
To control the beam through the Spin Rotator section there shall be a Beam Position Monitors placed throughout the spin rotator as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST.1
6.03.03
To measure and control the beam in the medium energy 400 MeV transfer line there shall be sufficient beam position monitors for orbit control, transverse profile monitors, and bunch charge monitors as required.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

F-EIS-METL-MAG-DIP.1
6.03.03
At the entry to the spin rotator section before the spin rotator solenoid there shall be a number of bending dipole to rotate the polarization spin from the Longitudinal direction into the transverse X direction.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-DIP.2
6.03.03
After the exit of spin rotator solenoid, there shall be a number of bending dipoles to close the geometry and direct the beam into the medium energy 400[MeV] transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.5
6.03.03
The spin rotator quadrupoles after the Spin rotator solenoid shall be able to match the beam beta functions βx and βy to that required for entry into the 400MeV transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.6
6.03.03
The spin rotator exit quadrupoles shall have at least 2 families this is required to control the electron beam optics as needed.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.7
6.03.03
The spin rotator solenoid shall rotate the electron beam spin from the X axis to the vertical y-axis before it enters the medium [400MeV] transport line to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.8
6.03.03
The spin rotator solenoid shall have an integrated gradient of 2.2 [T.m] required to rotate the spin from the horizontal axis to the vertical axis.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.1
6.03.03
The bump magnets shall have a rise and time consistent with the requirements of the circulating bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.2
6.03.03
The Pulsed bump magnets shall be able to create a closed orbit path passing close to the Septum and maintain it during each injection cycle (100-150 Hz).
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.6
6.03.03
Each train of four bunches shall be injected into neighboring RF buckets to facilitate bunch merges.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.7
6.03.03
The injection system shall be capable of maintaining the small spacing required by the injected bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.11
6.03.03
The injection system into the RCS shall be capable of injecting successive bunches into the RCS to create a bunch train with four bunches each circulating in the RCS ready to be merged.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.12
6.03.03
The RCS shall be capable of merging each train of 4 bunches into a larger single bunch to create larger single circulating bunche in the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.2
6.03.03
The Medium energy transfer line shall contain 3 sections: 1. Spin rotation section, 2. The main transfer line, 3. The Injector system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.3
6.03.03
There will be number of corrector Quadrupoles after the Pre-Injector longitudinal matching and before the spin rotator to provide beam matching into the Spin Rotator.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.4
6.03.03
The medium energy 400 MeV transfer line shall be able to transport the spin reoriented beam from the spin rotator to the RCS injection system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.5
6.03.03
The medium energy 400 MeV transfer line will maintain the spin direction of the beam along the entire transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.6
6.03.03
The spin rotator shall ensure the spin direction of the electron bunches are rotated from the longitudinal Z axis to the vertical Y axis.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH-INST.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be beam position monitor (BPM), and a transverse profile monitor at the entry to the buncher cavity to measure beam loss, position, and charge.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.2
6.06.03
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), beam position monitors and transverse profile monitors
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.3
6.06.03
To characterize the beam as it exits the buncher section, there shall be an emittance measurement including slit and beam viewer, an integrating current transformer, beam position monitor, charge and compression during commissioning.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-MAG.1
6.03.04
A seris of the solenoid magnets shall placed between the Wien filter up to the beam energy of 10 MeV.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-MAG.2
6.03.04
The Solenoid has the Bz.l total equal to zero. Bz is free to tune.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-MAG.3
6.03.04
Air core mangets shall placed closeby with each solenoid to correct beam orbit
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.2
6.08
The bunching section shall generate sufficient compression to compress the bunch length to that required by [5.9].
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.3
6.08
The bunchers rf voltage and phase will be synchronized so that the passing electron bunches meet the required beam characteristics at the end of the buncher section.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-LINAC-VAC.1
6.03.04
The LINAC section shall contain enough strategically located Vacuum gate valves, to allow access to the vacuum volume as needed.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.1
6.03.03
The LTR transfer line shall terminate with an injection system capable of transferring the beam into the RCS for all the operating energies and conditions specified in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.3
6.03.03
The vertically spin polarized electron bunch patterns generated by the pre-injector shall be transferred into the RCS unaltered.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.1
6.08
There shall be a special RF kicker to kick the injected beam into neighboring RF buckets without disturbing the 8 circulating bunches.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ.1
6.03.04
The EIS Pre-Injector shall consist of 3 sub-systems: 1. An electron gun section, followed by 2. A low energy transfer line and bunching section, followed by 3. A LINAC section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-INST.1
6.03.04
EIS shall have all the beam instrumentation necessary to deliver the operational parameters set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-HETL-INST-BPM-ELEC.01
6.03.03.04.01
The BPM single bunch measurement resolution for a (1 - 4 nC) pilot bunch shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.02
6.03.03.04.01
The BPM single bunch measurement resolution for (5.5 - 28 nC) bunches shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.03
6.03.03.04.01
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.04
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used to measure the transport lattice.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.01
6.03.03.04.01
The BPM Pickup alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.02
6.03.03.04.01
The BPM Pickup shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.04
6.03.03.04.01
The BPM Pickups shall be located by the dipole correctors at every second quadrupole.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM-ELEC.01
6.03.03.04.01
For a (1 nC) pilot bunch, the BPM single bunch measurement resolution shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.02
6.03.03.04.01
For (5.5 - 10 nC) bunches, the BPM single bunch measurement resolution shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.03
6.03.03.04.01
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.04
6.03.03.04.01
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.01
6.03.03.04.01
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.02
6.03.03.04.01
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.04
6.03.03.04.01
The location of the BPM Pickups shall be TBD
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.01
6.03.02.05.04
A synchrotron light monitor (SLM) shall be installed in the RCS ring downstream of an RCS dipole magnet
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.02
6.03.02.05.04
The location of the SLM light extraction port shall be- TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.03
6.03.02.05.04
The synchrotron light shall be transported from the RCS light extraction port to an optical table for detection.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.04
6.03.02.05.04
The synchrotron light optical table shall have a streak camera and gated camera shall be installed.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.05
6.03.02.05.04
The SLM shall be able to make Turn-by-turn measurements using gated cameras to provide measurements of; the injection matching parameters and the beam position stability parameters during acceleration. TBD -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.06
6.03.02.05.04
The SLM shall be used to provide horizontal and vertical transverse profile measurements on bunches with charges > 6nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.07
6.03.02.05.04
The SLM horizontal and vertical transverse profile measurements shall be measured with a resolution in both planes of 0.1 mm
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.08
6.03.02.05.04
The SLM shall be used to provide longitudinal profile measurements
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.09
6.03.02.05.04
A dual sweep streak camera shall be used to provide measurements of the bunch length and longitudinal profiles
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.10
6.03.02.05.04
The dual sweep streak camera shall have a resolution of <5 ps
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.11
6.03.02.05.04
The profile measurements shall be used, together with modeled or measured beam optics to infer the beam emittances and energy spread.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.12
6.03.02.05.04
The Vertical emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.6 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.13
6.03.02.05.04
The Horizontal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 10 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.14
6.03.02.05.04
The Longitudinal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.00001 eV-s
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.15
6.03.02.05.04
The Energy spread measurement, for bunch charges > 6nC, shall be measured with a precision of 0.0001 dp/p
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.01
6.04.06.02
A bunch pattern monitor shall be installed in the ESR to measure indiviual bunch charge with an accuracy 1 %
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.02
6.04.06.02
The Bunch pattern monitor shall be capable of measuring Bunch patterns ranging from a single bunch, to a filled ring with 1,160 bunches
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.01
6.04.06.05
BLM shall be needed to needed to protect sensitive equipment.
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.02
6.04.06.05
The number of BLM installed in the ESR shall be TBD ea
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.03
6.04.06.05
BLM shall be installed at the following locations in the ESR TBD
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.04
6.04.06.05
The sensitivity of the BLM detectors shall be TBD units?
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.05
6.04.06.05
Where possible existing RHIC BLM's can be relocated to identify ESR & HSR losses
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.06
6.04.06.05
The response time from loss detection to abort shall be TBD us
05/16/2025
In Process
FALSE

P-ESR-INST-BPM-ELEC.01
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following capabilities defined for the low intensity pilot injection energies and high intensity collision energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following time resolutions for data refresh defined for the beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.03
6.04.06.01
The ESR BPM Electronics shall have the following time resolutions for data logging defined for the beam energies:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.04
6.04.06.01
The ESR BPM Electronics shall have the following measurement resolutions defined for beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.05
6.04.06.01
The ESR BPM Electronics shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.06
6.04.06.01
The ESR BPM Electronics shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-PU.01
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall provide dual plane (horizontal and vertical) beam positional measurements.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) shall be positioned in the following locations approved by physics as defined in the lattice:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.03
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) mechanical and electrical center in the locations identified shall be:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.04
6.04.06.01
The ESR Beam Position Monitor Pick-Ups housing shall have a +/- 10 (mrad) corresponding to +/- 0.6 (degree) roll tolerance with regards to BPM measurements in respect to the vacuum chamber.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.05
6.04.06.01
The ESR Beam Position Monitor Pick-Ups design shall be less than or equal to the allocated impedance and is within the accepted overall ESR impedance budget approved by physics. (replace with loss factor)
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.06
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall fulfill resolution requirements over the horizontal and vertical beam position range with respect to its fiducials of +/- 3 (mm).
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.07
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to ensure the maximum temperatures of the components (due to heating by the beam) are acceptable for reliability and operations of the EIC over the planned operational life of 20 (yrs).
09/15/2025
In Process
FALSE

P-ESR-INST-BPM-PU.09
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to be baked to 250 °C for UHV processing.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.10
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.11
6.04.06.01
The ESR BPM Pickup shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/30/2025
In Process
FALSE

P-ESR-INST-BPM-PU.12
6.04.06.01
The ESR Beam Position Monitor Button configuration will be mirror symmetric with respect to the mid-and center planes. Deviation from symmetry shall be such that corresponding BPM reading errors are less then 20 microns.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.13
6.04.06.01
The ESR Beam Position Monitor Pick-Ups symmetrical configuration (postion between the four buttons and the relative to the fiducials on top of the button) shall be stable under the inference of the expected operational thermal changes to the extent that corresponding changes in the bpm reading deviate less than 20 µm.
07/25/2025
Approved
FALSE

P-ESR-INST-DCCT.01
6.04.06.02
A DCCT shall measure the average beam current in the ESR.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.02
6.04.06.02
The measurement resolution averaged over 1 sec shall be < 5 uA
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.03
6.04.06.02
The DCCT beamline device impedance shall be approved by beam physics.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.04
6.04.06.02
Measurement drift tolerance (thermal effects) shall be ≤ 1 uA/K
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.05
6.04.06.02
The DCCT sensor in the ring shall operate in the temperature range of 15 to 35 degrees C
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.06
6.04.06.02
The range of average beam current to be measured shall be 0.156x10-3 to 2.5 A
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.07
6.04.06.02
The DCCT system shall have a remote controlled self calibration system
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.08
6.04.06.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.09
6.04.06.02
The measured average current shall be provided to users at a rate of 10 Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.10
6.04.06.02
The measured average current shall be archived at a rate of 10 Hz Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.11
6.04.06.02
The DCCT sensor assembly in the ring shall be radiation resistant
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.01
6.04.06.03
The requirements for longitudinal feedback are ??? TBD
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.02
6.04.06.03
The Longitudinal feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.01
6.04.06.04
The ESR shall have two synchrotron light monitors (SLM) and one X-ray pin hole monitor
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.02
6.04.06.04
The longitudinal bunch profile monitor shall have a turn-by-turn capability based on a single bunch in the fully filled bunch train.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.03
6.04.06.04
TThe SLM systems shall measure the crabbing angle, longitudinal bunch parameters, H & V beam size and global coupling.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.04
6.04.06.04
The SLM shall be able to measure a crabbing angle of 12.5 mrad with accuracy of 10 %
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.05
6.04.06.04
The SLM shall be able to measure the Longitudinal bunch parameters with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.06
6.04.06.04
The SLM shall be able to measure the H & V beam size with accuracy of H=?? V=?? units
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.07
6.04.06.04
The SLM shall be able to measure the Global coupling with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.08
6.04.06.04
One SLM port shall be located downstream of a dipole in an appropriate location in the ESR, exact location not critical.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.09
6.04.06.04
The second SLM port shall be located in a complimentary location in the lattice to ensure all the necessary SLM measurements can be made. TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.10
6.04.06.04
The SLM light extraction port mirrors shall be good quality, having a surface finish better than 1/10 Lambda
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.11
6.04.06.04
The SLM light extraction port mirrors shall be water cooled to avoid image distortion.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.12
6.04.06.04
There shall be an enclosed SL transport from the light extraction port to the SLM optical lab rooms. Length to be determined by the distance to optical lab room, should be minimized to reduce vibration problems.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.13
6.04.06.04
The locations of the SLM optical lab rooms shall be TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.14
6.04.06.04
The double-slit interferometer method shall be used to measure transverse beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.15
6.04.06.04
The standard transverse resolution of an SLM using visible light shall be ~60 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.16
6.04.06.04
The resolution using the double-slit method shall equal to 10 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.17
6.04.06.04
A streak camera shall be used to measure the bunch longitudinal profiles
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.18
6.04.06.04
A position sensitive photo-diode will provide photon beam centroid information which shall supplement the orbit stability measurements by the BPMs
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.19
6.04.06.04
A GigE CCD/CMOS camera, externally triggerable with exposure times ranging from 10 nsec to 5 sec, shall be used to image the visible radiation
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.20
6.04.06.04
A commercially available gated camera with gate width of <2 nsec (compared to a minimum bunch spacing of 10 nsec) shall be used to detect injection oscillations and for beam studies.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.21
6.04.06.04
The location of the X-ray pinhole monitoring system shall be TBD
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.22
6.04.06.04
The target resolution of the X-ray pin hole monitoring system shall be ~ 5 um (or as best that can be achieved with the machine parameters and commercial equipment) 5 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.23
6.04.06.04
The X-ray pin hole monitor shall provide independent measurement of the energy spread and horizontal/vertical emittance. H=V=15.4 nm
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.24
6.04.06.04
The X-ray pinhole photon beamline shall be equipped with gated cameras that will be employed to provide high resolution turn-by-turn profile measurements
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.25
6.04.06.04
A pinhole assembly including tungsten slits shall provide sufficient resolution to precisely measure the beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.26
6.04.06.04
Several different size pinholes sizes shall be incorporated to allow easy alignment and measurements at different beam currents and energies.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.01
6.04.06.03
Stripline kickers (H & V) shall be used to excite the beam so tunes can be measured using turn-by-turn BPM data.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.02
6.04.06.03
The magnitude of the kick required for the horizontal kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.03
6.04.06.03
The magnitude of the kick required for the vertical kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.04
6.04.06.03
The kicker waveform (risetime and shape) requirements shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.05
6.04.06.03
The location of the tune meter kicker striplines in the ESR shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.06
6.04.06.03
The impedance of the kicker beamline device shall be approved by beam Physics.
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.01
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.03
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.02
6.04.06.03
The transverse feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSSLFB.01
6.04.06.03
The transverse slow feedback system bandwidth shall bs 10 Hz
05/16/2025
In Process
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.2
6.03.04
At the end of the Zigzag there shall be a diagnostic section (details TBD) to measure the bunch length and dP/P.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-DIP.1
6.03.04
The ZigZag section shall consist of a number of dipoles separated by drift spaces in a R56 configuration to increase the bunch length to 40ps.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-QUAD.1
6.03.04
The ZigZag section shall consist of a number of Quadrapoles to control the beam dispersion through the zigzag.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.2
6.03.04
The longitudinal matching section shall consist of a so-called Zigzag section followed by a de-chirp cavity which will stretch the bunch length to 40 ps, reduce the energy spread, and generate a longitudinal phase space rotation of the bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.3
6.03.04
At the Zigzag exit, the electron beam’s average spin orientation shall be longitudinal in the direction of beam travel.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.1
6.03.03
The fast kicker magnet shall be capable of deflecting the electron beam from the RCS to counter the RF kick.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.4
6.03.03
The spin rotator entry quadrupole shall have at least 2 families this is needed to control the electron beam optics as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.1
6.03.03
The Medium energy transfer line shall transfer the beam from the pre-injector longitudinal matching section to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH-RF.1
6.08
one 197 MHz buncher cavity shall be used for providing bunch chirp
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.1
6.03.03
The pre-injector LEBT low energy RF section shall transfer the electron beam from the gun to the linac section. shall provide bunching and initial acceleration to each 1 nC bunch
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.4
6.08
The Pre-Injector layout shall accommodate all RF cavities and allow enough room for other Pre-Injector components.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-GUN.2
6.03.04
The pre-injector electron gun shall produce all the bunch patterns required to deliver the ESR beam requirements set forth in [5.9].
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.21
6.03.04
The diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.1
6.03.03
The pre-injector shall have a low energy transfer line from the gun into the beam compression "Bunching" section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.6
6.03.04
Following the gun, there shall be multiple groups of magnets required to control the electron beam.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.7
6.03.04
To characterize and control the fresh bunches the low energy transfer line from the Gun to the Buncher shall contain a plunging transverse profile monitor, a bunch charge monitor, beam loss monitors, and beam position monitors
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-TLINE-MEBT-MAG-QUAD.1
6.03.03
The corrector Quadrupoles shall be able to suppress the βx and βy along the transfer line to levels consistent with those required ate the RCS injection kicker.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-SEP.1
6.03.03
The septum magnet shall be capable of deflecting the incoming electron beam into the RCS and shielding the circulating beam already in the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.2
6.03.03
The injection system shall inject the beam at Need update
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.4
6.03.03
The injection system shall be able to inject one bunch per injection kick using RF and magnetic kickers to build up a total of 8 bunches from 4 kicks to the RF and kickers.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.5
6.03.03
The injection system shall ensure the bunch emittance shall match the requirements of the RCS RF system and such, to avoid collective instabilities and to stay within the off-momentum aperture.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.9
6.03.03
The injection system shall contain 3 bump magnets to locally bump the RCS circulating beam close to the injection septum.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.10
6.03.03
The RCS injection system shall contain an RF kicker and a pulsed magnet followed by a septum magnet to redirect the beam into the RCS closed orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.11
6.03.03
The magnetic field of the injection system pulsed magnet shall follow the rise time of the power amplifiers which drive the RF kickers..
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.2
6.08
The special kicker shall consist of an RF harmonic kicker with fundamental frequency of 1/4 of the main RCS RF cavity or compatible equivalent alternative.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.3
6.08
The special kicker shall have a rise and fall time that matches the RF bucket size.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.4
6.08
The special kicker shall have a peak power necessary to generate a kick to inject the bunch into the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.5
6.08
The special kicker shall have a macro pulse with a flattop that is greater than the time between the LINAC bunches and shall have a rise and fall time less than 1 RCS turn.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.6
6.08
The special kicker shall be able to repeat at the LINAC pulse rate.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT.28
6.03.03
The LTR transfer line shall have several FODO quadrupoles to control the beta function along the transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ.3
6.03.04
The EIS Pre-Injector shall create bunches which meet the requirements set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-RCS-MAG-QUAD.5
6.03.02
The quadrupoles shall be individually powered with low supplementary current/voltage power supplies for beam-based alignment purposes.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.7
6.03.02
The RCS straight sections shall have the appropirate number of defocusing and focusing quadrupole families per straight section.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.9
6.03.02
The non-colliding straights will have different scheme.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.14
6.03.02
The main arc quadrupoles shall be powered by a total of 2 power circuits 1 for focusing the other defocusing.
05/16/2025
In Process
FALSE

F-EIS-RCS-MAG.15
6.03.02
The quadrupoles in both straight sections shall need a total of 6 power circuits to power all six families of quadrupoles in both straights. (straights are optically identical)
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.18
6.03.02
The RCS magnets shall be fed by a system of power supplies matched in voltage and maximum current to the specifications and requirements of the respective magnets.
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-BUMP.1
6.03.03
the RCS extraction system shall have three fast bump magnets to direct the bunches to the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-FKICK.1
6.03.03
RCS extraction shall be facilitated with a fast kicker having a rise time of 2 micro-secs
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker shall operate in unison with a septum magnet which can direct the beam into the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.1
6.03.03
The beam injection of the electron bunches from the RCS into the ESR ring shall take place in the 12 o’clock straight section.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.2
6.03.03
There will be two electron bunches circulating in the RCS at extraction, these shall be injected into the High Energy Transfer Line which connects the RCS to the ESR.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.1
6.08
The RF system shall Provide a maximum RF voltage of 60MV to accelerate the beam.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.2
6.08
The total RF power provided by the RF amplifiers shall be able to compensate for all additional losses created by the stored electron beam in addition to the acceleration and synchrotron losses.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.3
6.08
The RF system shall Provide sufficient gradient to allow installation of all necessary RF modules in the limited space in IR 10.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.4
6.08
The RF system shall be able to accommodate 4 circulating bunches in one trains of 4 bunches.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.5
6.08
The RF system shall be able to merge the one train of 4 bunches into two larger separate circulating bunches then merge these two large bunches into a single larger circulating bunch.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.6
6.08
The RF system shall be able to accelerate final large, merged bunch to the operating energies needed by the ESR as set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.7
6.03.02
The RF system controls shall be designed to handle the transient beam loading for all bunch structures.
05/16/2025
In Process
FALSE

F-EIS-RCS-VAC.1
6.03.02
The vacuum chamber shall provide sufficient horizontal and vertical aperture to accommodate a beam which is 5 σ larger than the largest sigma beam size determined by the injected RMS emittance.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.2
6.03.02
The average dynamic pressure around the ring shall be < 5e-8[Torr] after 1 year of operation.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.3
6.03.02
The impedance of the entire RCS vacuum system shall allow for the bunch intensities, beam currents, and bunch numbers contained in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.09
6.03.02.04
The vacuum chamber shall be capable of absorbing and carrying away the eddy current power.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.4
6.03.02
The vacuum chamber and all its components shall be designed to withstand the total synchrotron radiation loads seen in operation.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-VAC.08
6.03.02.04
The vacuum chamber shall be capable of absorb synchrotron radiation and carrying away the absorbed power.
05/16/2025
Approved
FALSE

F-EIS-RCS.1
6.03.02
The RCS shall consist of two parts 1. The main RCS Ring, and 2. The High energy transfer line terminating with the ESR injection system
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.2
6.03.03
The RCS shall be capable of accepting the bunches and matching the bunch parameters as injected by the BAR into the LTR transfer line.
05/16/2025
In Process
FALSE

F-EIS-RCS.3
6.03.02
After bunch injection into the RCS, the RCS shall merge the injected bunches into two bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.4
6.03.02
After bunch injection the RCS shall be able to accelerate the single bunch to the final desired energy set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS.5
6.03.02
The RCS needs to accelerate to the top possible energy in a time interval consistent with the parameters set forth in [5.9] at approximately 100 msecs for 18 GeV.
05/16/2025
In Process
FALSE

F-EIS-RCS.6
6.03.03
The RCS shall be capable of kicking the accelerated bunches into the RTE transfer line to the ESR.
05/16/2025
In Process
FALSE

F-EIS-RCS.7
6.03.02
RCS will need to increase the vertical emittance to match the ESR vertical emittance.
05/16/2025
In Process
FALSE

F-EIS-RCS.8
6.03.02
The RCS shall have a racetrack design with 160 arc FODO cells, bending radius of 91.67 m and two 86.624 m straight sections made up of 8 FODO cells with a total circumference of 1.421 km
05/16/2025
In Process
FALSE

F-EIS-RCS.15
6.03.02
The RCS lattice shall contain provisions for correctors such as dipole correctors etc., as needed.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-TLINE-GUN-Diagnostic.1
6.03.04
The Pre-injector separate diagnostic beamline section shall have 3 branches one with Faraday cup, one port containing a connection to the cathode Laser and a line to a low energy beam dump.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.1
6.03.04
The instrumentation in the diagnostic beamline to the low energy beam dump shall have the capability to measure beam position, profile, bunch charge
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.4
6.03.04
The Faraday cup shall be able to measure the charge of the electron bunches from the gun.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-LASER-INST.1
6.03.04
There shall be instrumentation capable of measuring the position and profile of the laser beam on the cathode.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-LASER.1
6.03.04
The laser beam shall illuminate the cathode perpendicular to the cathode face
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.1
6.03.04
The beam tube and flange sizes shall be appropriate to transport polarized e-beam between the e-source and the diagnostic beam line polarimeter chamber.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.2
6.03.04
Vacuum system shall be compatible with UHV requirements.
05/16/2025
Not Applicable
FALSE

F-EIS-TLINE-SPIN.INST.1
6.03.03
Profile monitor, BPM are placed at before, in between and after two Wien filters
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.1
6.03.03
Between the dipole chamber and the bunching section, two Wien filters shall be used as spin rotator to rotate the spin direction from longitudinal to vertical.
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.2
6.03.03
triplets focusing are used in between the two Wien filters to maintain the beam envolop
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.3
6.03.03
Quadpole single let and double let are used before and after Wien to compensate the quadropole components from the Wien entrance and exit
05/16/2025
In Process
FALSE

F-EIS-VAC.1
6.03.04
The EIS vacuum system shall meet UHV standards at a minimum (Ref vacuum spec?)
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.07
6.03.02.04
On 15 m on each side (or one vacuum section) of the SRF cavities the vacuum system shall be processed to class ISO 5.
05/16/2025
Approved
FALSE

F-EIS-VAC.2
6.03.04
The impedance of the entire EIS vacuum system, including the transport lines, shall allow for the bunch intensities, beam currents, and bunch numbers contained in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.01
6.03.03.03
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.03
6.03.03.03
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.01
6.03.03.03
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.03
6.03.03.03
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-VAC.3
6.03.04
The size, location and type of vacuum pumps shall be chosen to meet the required vacuum levels during operation
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-VAC.4
6.03.04
Appropriate vacuum gauging shall be supplied in each vacuum sector to monitor the required vacuum levels
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

G-EIS.5x
6.09
The EIS shall have a cryogenic system to cool and operate all elements which need cryogenic cooling and will, where possible utlise the existing RHIC cooling system.
05/16/2025
Not Applicable
FALSE

G-EIS.6
6.03
The EIS shall inject into the ESR at a rate of 1[Hz].
05/16/2025
Approved
FALSE

F-EIS- PREINJ-LINAC-MAG.1
6.03.04
A Quadrupole triplet shall be installed between each accelerating structure in the LINAC to control the beam beta function and dispersion.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.2
6.03.04
The LINAC Quadrupole triplets shall be optimized to control beams with high RCS injection energies ~ 400[MeV].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.3
6.03.04
In addition to the Quadrupole triplets X Y steering coils shall be installed between each 2.856[GHz] accelerator structure to control the beam beta function and dispersion in the LINAC.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.4
6.03.04
A LINAC XY steering coils shall be optimized to control beams which have low RCS injection energies < < 400[MeV]
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.1
6.03.04
The Pre-Injector S-band LINAC shall be able to accelerate all electron bunches up to the energy's required by [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.2
6.03.04
The Pre-Injector LINAC frequency shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.3
6.03.04
The Pre-Injector LINAC rep-rate shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.1
6.03.02
The instrumentation system shall contain a Beam Position Monitor system consisting of dual-plane Beam Position Monitors adjacent to each quadrupole.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.2
6.03.02
Select Beam Position Monitors in the injection region shall have turn-by-turn orbit measurement capability based on a single, remotely selectable bunch out of the fully filled bunch train to enable injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.3
6.03.02
The instrumentation system shall include a beam current monitor to measure average beam current.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.4
6.03.02
The instrumentation system shall include a system to measure individual bunch charges and bunch pattern.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.5
6.03.02
The instrumentation system shall include a system to measure transverse bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.6
6.03.02
The instrumentation system shall include a system to measure longitudinal bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.7
6.03.02
The instrumentation system shall contain a betatron and synchrotron tune monitors.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.8
6.03.02
The longitudinal bunch profile monitor needs turn-by-turn capability based on a single bunch in the fully filled bunch train to allow timing and energy adjustment for injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.9
6.03.02
The RCS shall contain a beam-based alignment system.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.10
6.03.02
The RCS shall contain a beam loss monitor system at select regions.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.3
6.03.02
The sextupoles shall be sorted into appropriate “families” and powered accordingly.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.4
6.03.02
There shall be dipole correctors capable of adjusting the beam orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.6
6.03.02
The quadrupoles shall generally be arranged in a conventional FODO structure.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.7
6.03.02
Each quadrupole strength needs to be capable of being changed independently by small amounts for beam-based alignment purposes.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.8
6.03.02
Sextupoles shall be sorted into “families” with the family structure dependent on the linear lattice configuration (betatron phase advance per FODO cell).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.9
6.03.02
The maximum integrated field strength of the FODO sextupoles needs to be sufficient to correct chromaticity to within 1 unit in both planes.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.10
6.03.02
Window-frame dipole corrector magnets capable of providing both horizontal and vertical dipole fields to correct the beam orbit in both transverse planes shall be placed adjacent to most of the quadrupoles.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.11
6.03.02
The strength of the window-frame dipole correctors needs to be chosen to correct for any source of orbit distortion and should have a margin for beam based diagnostic purpose.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-GUN-INST.4
6.03.04
To characterize and control the fresh bunches sent to the Mott polarimeter, the gun diagnostic beamline shall contain instrumentation to measure and control the profile, position, and charge of the beam.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-INST.5
6.03.04
The Diagnostic beamline section shall have one Beam Profile Monitor and Wien Filter and an electrostatic bender before the Mott polarimeter and Faraday Cup.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-GUN-INST.6
6.03.04
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

F-EIS-GUN-MAG.1
6.03.04
Following the DC gun, the electron bunch shall be deflected through a bending dipole into the Bunching section
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.2
6.03.04
2 solenoids shall be placed between the gun and the bending dipole into the bunching section capable of correcting the beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.3
6.03.04
Provision shall be made for an appropriate number of air cored steering coils between the Gun and bunching section to correct the electron beam position as required.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.4
6.03.04
A bending dipole shall follow the Gun and be able to bend the beam from the gun into the bunching section OR bend separate electron bunches into the separate diagnostic beam line.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.5
6.03.04
The bending dipole after the gun shall also have the capability to deflect the beam enough to allow a laser to illuminate the photocathode head on.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.6
6.03.04
A minimum of three solenoids shall be placed between the gun and the first bunching cavity to maintain the beam size for 5–10 nC bunches
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.7
6.03.04
Short air core trim coils shall be used to correct beam position for energies greater than 100 keV
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.8
6.03.04
The Diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-VAC.3
6.03.04
The Laser section shall be independent from the Gun\diagnostic section vacuum.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN.3x
6.03.03
The low energy transfer line shall have an additional branch between the Gun and the Bunching section which can transfer individual electron bunches into the diagnostic beamline section.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.4x
6.03.03
The low energy transfer line shall have a laser port between the Gun and the Bunching section which will allow an optical path for the laser to illuminate the cathode face of the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.6x
6.03.04
The gun shall have steering coils to direct the liberated electrons (These can be reused from the existing Gun system.)
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-HETL-ESR-INJ.1
6.03.03
The transferred beam shall meet all the requirements of the circulating beam, for all operational modes of the ESR as set forth in [5.9].
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-INST-BPM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed Beam Position Monitors at the quadrupoles and at the entry and exit of a number of the dipoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-IC.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain FCT and an Integrating Current Transformer before the ESR injection septum.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-PM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed YAG\OTR at the entry and exit of a number of the diploes and quadrupoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-POL.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a system to measure the beam polarization.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-BUMP.1
6.03.03
ESR injection shall have three fast bump magnets to direct the bunches from the HETL into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker of the ESR injector system shall operate in unison with a septum magnet which can direct the beam into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-SLINE-FKICK.1
6.03.03
The ESR injection system shall have a fast strip line kicker with a rise time of 2nsecs .
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.1
6.03.03
The High Energy Transfer Line shall match the beam parameters between the extraction point of the RCS and injection point of the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.2
6.03.03
The extraction into the required High Energy transfer line shall match the ESR bunch spacing and spin pattern.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.3
6.03.03
The High Energy Transfer Line shall be spin transparent.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.4
6.03.03
The ESR extraction system shall have another three bump magnets, its own septum magnet and use the strip line injection kicker to extract and replace the circulating bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BLM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be a bunch length monitor(BLM) at the exit of the 3rd harmonic buncher cavity to measure bunch compression during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam position monitor (BPM) at the entry to the 1st harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section a beam position monitor (BPM) at the entry and exit of the 2nd harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.3
6.03.04
To characterize the beam as it exits the buncher section, beam position monitor(BPM) at the exit of the 3rd harmonic buncher cavity to measure beam position during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-EM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be an emittance monitor(EM), at the exit of the 3rd harmonic buncher cavity to measure beam position, the beam emittance during commissioning.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-EM.01
6.03.04.02.06
Emittances shall be measured using a profile monitor and a dedicated upstream quadrupole configured to measure H, V, and skew profiles.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.03
6.03.04.02.06
The EM shall be able to measure the expected normalized emittance of 40 um
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.02
6.03.04.02.06
Before the 400 MeV beam goes into the spin rotator, the emittance shall be measured by a quad scan
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.04
6.03.04.02.06
Beam emittance shall be measured in the low energy diagnostics beamline using a slit scanner and profile monitor
05/16/2025
On Hold
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.1
6.03.04
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), at the entry and exit of the 2nd harmonic buncher cavity to measure charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.2
6.03.04
To characterize the beam as it exits the buncher section, an integrating current transformer(ICT) at the exit of the 3rd harmonic buncher cavity to measure the bunch charge during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-LM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam loss monitor (BLM) at the entry to the 1st harmonic buncher cavity to measure beam loss
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a transverse profile monitor(TPM) at the entry to the 1st harmonic buncher cavity to measure the charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section there shall be a transverse profile monitor(TPM) at the entry and exit of the 2nd harmonic buncher cavity to measure the bunch profille.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.3
6.03.04
To characterize the beam as it exits the buncher section, transverse profile monitor(TPM) at the exit of the 3rd harmonic buncher cavity the bunch profile during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-MAG-SOL.4
6.03.04
The solenoidal field shall extend to also contain the 1st RF tank of the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-CAV.1
6.08
The LINAC TWP cavities shall be constant gradient cavities
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-INST-CM.1
6.03.04
Bunch charge measurements shall be performed at multiple locations through the LINAC.
05/16/2025
In Process
FALSE

F-EIS-LINAC-INST-PM.1
6.03.04
To measure the beam profile in the LINAC section there shall be a plunging YAG/OTR transverse profile monitor between the 1st and 2nd accelerating cells.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-QUAD.3
6.03.04
A drift space with quadrupole triplets shall be placed between each TWP structure to tune the bunch beta function through the LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.3
6.03.04
Between each S-band LINAC section there shall be at least two window frame steering magnets.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.4
6.03.04
Additionally, window frame steering magnets will be placed at the entry and exit of each accelerating structure to position the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.1
6.03.04
Following the Zigzag there shall be a de-chirp cavity to linearize and reduce the energy spread of the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.1
6.03.04
A longitudinal matching section shall follow the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.1
6.03.03
The fast kicker magnet shall be capable of deflecting the electron beam from the RCS to counter the RF kick.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST-BPM.1
6.03.03
To control the beam through the Spin Rotator section there shall be a Beam Position Monitors placed throughout the spin rotator as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST.1
6.03.03
To measure and control the beam in the medium energy 400 MeV transfer line there shall be sufficient beam position monitors for orbit control, transverse profile monitors, and bunch charge monitors as required.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

F-EIS-METL-MAG-DIP.1
6.03.03
At the entry to the spin rotator section before the spin rotator solenoid there shall be a number of bending dipole to rotate the polarization spin from the Longitudinal direction into the transverse X direction.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-DIP.2
6.03.03
After the exit of spin rotator solenoid, there shall be a number of bending dipoles to close the geometry and direct the beam into the medium energy 400[MeV] transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.4
6.03.03
The spin rotator entry quadrupole shall have at least 2 families this is needed to control the electron beam optics as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.6
6.03.03
The spin rotator exit quadrupoles shall have at least 2 families this is required to control the electron beam optics as needed.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.7
6.03.03
The spin rotator solenoid shall rotate the electron beam spin from the X axis to the vertical y-axis before it enters the medium [400MeV] transport line to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.8
6.03.03
The spin rotator solenoid shall have an integrated gradient of 2.2 [T.m] required to rotate the spin from the horizontal axis to the vertical axis.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.1
6.03.03
The bump magnets shall have a rise and time consistent with the requirements of the circulating bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.2
6.03.03
The Pulsed bump magnets shall be able to create a closed orbit path passing close to the Septum and maintain it during each injection cycle (100-150 Hz).
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.6
6.03.03
Each train of four bunches shall be injected into neighboring RF buckets to facilitate bunch merges.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.7
6.03.03
The injection system shall be capable of maintaining the small spacing required by the injected bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.11
6.03.03
The injection system into the RCS shall be capable of injecting successive bunches into the RCS to create a bunch train with four bunches each circulating in the RCS ready to be merged.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.12
6.03.03
The RCS shall be capable of merging each train of 4 bunches into a larger single bunch to create larger single circulating bunche in the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.1
6.03.03
The Medium energy transfer line shall transfer the beam from the pre-injector longitudinal matching section to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.2
6.03.03
The Medium energy transfer line shall contain 3 sections: 1. Spin rotation section, 2. The main transfer line, 3. The Injector system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.3
6.03.03
There will be number of corrector Quadrupoles after the Pre-Injector longitudinal matching and before the spin rotator to provide beam matching into the Spin Rotator.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.4
6.03.03
The medium energy 400 MeV transfer line shall be able to transport the spin reoriented beam from the spin rotator to the RCS injection system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.5
6.03.03
The medium energy 400 MeV transfer line will maintain the spin direction of the beam along the entire transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH-INST.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be beam position monitor (BPM), and a transverse profile monitor at the entry to the buncher cavity to measure beam loss, position, and charge.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.2
6.06.03
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), beam position monitors and transverse profile monitors
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.3
6.06.03
To characterize the beam as it exits the buncher section, there shall be an emittance measurement including slit and beam viewer, an integrating current transformer, beam position monitor, charge and compression during commissioning.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-RF.1
6.08
one 197 MHz buncher cavity shall be used for providing bunch chirp
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.2
6.08
The bunching section shall generate sufficient compression to compress the bunch length to that required by [5.9].
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.3
6.08
The bunchers rf voltage and phase will be synchronized so that the passing electron bunches meet the required beam characteristics at the end of the buncher section.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-LINAC-VAC.1
6.03.04
The LINAC section shall contain enough strategically located Vacuum gate valves, to allow access to the vacuum volume as needed.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-MAG-QUAD.1
6.03.03
The corrector Quadrupoles shall be able to suppress the βx and βy along the transfer line to levels consistent with those required ate the RCS injection kicker.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.1
6.03.03
The LTR transfer line shall terminate with an injection system capable of transferring the beam into the RCS for all the operating energies and conditions specified in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.2
6.03.03
The injection system shall inject the beam at Need update
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ.1
6.03.04
The EIS Pre-Injector shall consist of 3 sub-systems: 1. An electron gun section, followed by 2. A low energy transfer line and bunching section, followed by 3. A LINAC section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-INST.1
6.03.04
EIS shall have all the beam instrumentation necessary to deliver the operational parameters set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-HETL-INST-BPM-ELEC.01
6.03.03.04.01
The BPM single bunch measurement resolution for a (1 - 4 nC) pilot bunch shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.02
6.03.03.04.01
The BPM single bunch measurement resolution for (5.5 - 28 nC) bunches shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.03
6.03.03.04.01
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.04
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used to measure the transport lattice.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.01
6.03.03.04.01
The BPM Pickup alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.02
6.03.03.04.01
The BPM Pickup shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.04
6.03.03.04.01
The BPM Pickups shall be located by the dipole correctors at every second quadrupole.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM-ELEC.01
6.03.03.04.01
For a (1 nC) pilot bunch, the BPM single bunch measurement resolution shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.02
6.03.03.04.01
For (5.5 - 10 nC) bunches, the BPM single bunch measurement resolution shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.03
6.03.03.04.01
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.04
6.03.03.04.01
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.01
6.03.03.04.01
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.02
6.03.03.04.01
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.04
6.03.03.04.01
The location of the BPM Pickups shall be TBD
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.01
6.03.02.05.04
A synchrotron light monitor (SLM) shall be installed in the RCS ring downstream of an RCS dipole magnet
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.02
6.03.02.05.04
The location of the SLM light extraction port shall be- TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.03
6.03.02.05.04
The synchrotron light shall be transported from the RCS light extraction port to an optical table for detection.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.04
6.03.02.05.04
The synchrotron light optical table shall have a streak camera and gated camera shall be installed.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.05
6.03.02.05.04
The SLM shall be able to make Turn-by-turn measurements using gated cameras to provide measurements of; the injection matching parameters and the beam position stability parameters during acceleration. TBD -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.06
6.03.02.05.04
The SLM shall be used to provide horizontal and vertical transverse profile measurements on bunches with charges > 6nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.07
6.03.02.05.04
The SLM horizontal and vertical transverse profile measurements shall be measured with a resolution in both planes of 0.1 mm
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.08
6.03.02.05.04
The SLM shall be used to provide longitudinal profile measurements
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.09
6.03.02.05.04
A dual sweep streak camera shall be used to provide measurements of the bunch length and longitudinal profiles
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.10
6.03.02.05.04
The dual sweep streak camera shall have a resolution of <5 ps
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.11
6.03.02.05.04
The profile measurements shall be used, together with modeled or measured beam optics to infer the beam emittances and energy spread.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.12
6.03.02.05.04
The Vertical emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.6 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.13
6.03.02.05.04
The Horizontal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 10 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.14
6.03.02.05.04
The Longitudinal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.00001 eV-s
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.15
6.03.02.05.04
The Energy spread measurement, for bunch charges > 6nC, shall be measured with a precision of 0.0001 dp/p
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.01
6.04.06.02
A bunch pattern monitor shall be installed in the ESR to measure indiviual bunch charge with an accuracy 1 %
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.02
6.04.06.02
The Bunch pattern monitor shall be capable of measuring Bunch patterns ranging from a single bunch, to a filled ring with 1,160 bunches
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.01
6.04.06.05
BLM shall be needed to needed to protect sensitive equipment.
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.02
6.04.06.05
The number of BLM installed in the ESR shall be TBD ea
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.03
6.04.06.05
BLM shall be installed at the following locations in the ESR TBD
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.04
6.04.06.05
The sensitivity of the BLM detectors shall be TBD units?
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.05
6.04.06.05
Where possible existing RHIC BLM's can be relocated to identify ESR & HSR losses
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.06
6.04.06.05
The response time from loss detection to abort shall be TBD us
05/16/2025
In Process
FALSE

P-ESR-INST-BPM-ELEC.01
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following capabilities defined for the low intensity pilot injection energies and high intensity collision energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following time resolutions for data refresh defined for the beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.03
6.04.06.01
The ESR BPM Electronics shall have the following time resolutions for data logging defined for the beam energies:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.04
6.04.06.01
The ESR BPM Electronics shall have the following measurement resolutions defined for beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.05
6.04.06.01
The ESR BPM Electronics shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.06
6.04.06.01
The ESR BPM Electronics shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-PU.01
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall provide dual plane (horizontal and vertical) beam positional measurements.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) shall be positioned in the following locations approved by physics as defined in the lattice:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.03
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) mechanical and electrical center in the locations identified shall be:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.04
6.04.06.01
The ESR Beam Position Monitor Pick-Ups housing shall have a +/- 10 (mrad) corresponding to +/- 0.6 (degree) roll tolerance with regards to BPM measurements in respect to the vacuum chamber.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.05
6.04.06.01
The ESR Beam Position Monitor Pick-Ups design shall be less than or equal to the allocated impedance and is within the accepted overall ESR impedance budget approved by physics. (replace with loss factor)
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.06
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall fulfill resolution requirements over the horizontal and vertical beam position range with respect to its fiducials of +/- 3 (mm).
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.07
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to ensure the maximum temperatures of the components (due to heating by the beam) are acceptable for reliability and operations of the EIC over the planned operational life of 20 (yrs).
09/15/2025
In Process
FALSE

P-ESR-INST-BPM-PU.09
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to be baked to 250 °C for UHV processing.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.10
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.11
6.04.06.01
The ESR BPM Pickup shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/30/2025
In Process
FALSE

P-ESR-INST-BPM-PU.12
6.04.06.01
The ESR Beam Position Monitor Button configuration will be mirror symmetric with respect to the mid-and center planes. Deviation from symmetry shall be such that corresponding BPM reading errors are less then 20 microns.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.13
6.04.06.01
The ESR Beam Position Monitor Pick-Ups symmetrical configuration (postion between the four buttons and the relative to the fiducials on top of the button) shall be stable under the inference of the expected operational thermal changes to the extent that corresponding changes in the bpm reading deviate less than 20 µm.
07/25/2025
Approved
FALSE

P-ESR-INST-DCCT.01
6.04.06.02
A DCCT shall measure the average beam current in the ESR.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.02
6.04.06.02
The measurement resolution averaged over 1 sec shall be < 5 uA
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.03
6.04.06.02
The DCCT beamline device impedance shall be approved by beam physics.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.04
6.04.06.02
Measurement drift tolerance (thermal effects) shall be ≤ 1 uA/K
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.05
6.04.06.02
The DCCT sensor in the ring shall operate in the temperature range of 15 to 35 degrees C
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.06
6.04.06.02
The range of average beam current to be measured shall be 0.156x10-3 to 2.5 A
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.07
6.04.06.02
The DCCT system shall have a remote controlled self calibration system
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.08
6.04.06.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.09
6.04.06.02
The measured average current shall be provided to users at a rate of 10 Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.10
6.04.06.02
The measured average current shall be archived at a rate of 10 Hz Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.11
6.04.06.02
The DCCT sensor assembly in the ring shall be radiation resistant
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.01
6.04.06.03
The requirements for longitudinal feedback are ??? TBD
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.02
6.04.06.03
The Longitudinal feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.01
6.04.06.04
The ESR shall have two synchrotron light monitors (SLM) and one X-ray pin hole monitor
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.02
6.04.06.04
The longitudinal bunch profile monitor shall have a turn-by-turn capability based on a single bunch in the fully filled bunch train.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.03
6.04.06.04
TThe SLM systems shall measure the crabbing angle, longitudinal bunch parameters, H & V beam size and global coupling.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.04
6.04.06.04
The SLM shall be able to measure a crabbing angle of 12.5 mrad with accuracy of 10 %
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.05
6.04.06.04
The SLM shall be able to measure the Longitudinal bunch parameters with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.06
6.04.06.04
The SLM shall be able to measure the H & V beam size with accuracy of H=?? V=?? units
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.07
6.04.06.04
The SLM shall be able to measure the Global coupling with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.08
6.04.06.04
One SLM port shall be located downstream of a dipole in an appropriate location in the ESR, exact location not critical.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.09
6.04.06.04
The second SLM port shall be located in a complimentary location in the lattice to ensure all the necessary SLM measurements can be made. TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.10
6.04.06.04
The SLM light extraction port mirrors shall be good quality, having a surface finish better than 1/10 Lambda
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.11
6.04.06.04
The SLM light extraction port mirrors shall be water cooled to avoid image distortion.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.12
6.04.06.04
There shall be an enclosed SL transport from the light extraction port to the SLM optical lab rooms. Length to be determined by the distance to optical lab room, should be minimized to reduce vibration problems.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.13
6.04.06.04
The locations of the SLM optical lab rooms shall be TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.14
6.04.06.04
The double-slit interferometer method shall be used to measure transverse beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.15
6.04.06.04
The standard transverse resolution of an SLM using visible light shall be ~60 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.16
6.04.06.04
The resolution using the double-slit method shall equal to 10 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.17
6.04.06.04
A streak camera shall be used to measure the bunch longitudinal profiles
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.18
6.04.06.04
A position sensitive photo-diode will provide photon beam centroid information which shall supplement the orbit stability measurements by the BPMs
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.19
6.04.06.04
A GigE CCD/CMOS camera, externally triggerable with exposure times ranging from 10 nsec to 5 sec, shall be used to image the visible radiation
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.20
6.04.06.04
A commercially available gated camera with gate width of <2 nsec (compared to a minimum bunch spacing of 10 nsec) shall be used to detect injection oscillations and for beam studies.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.21
6.04.06.04
The location of the X-ray pinhole monitoring system shall be TBD
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.22
6.04.06.04
The target resolution of the X-ray pin hole monitoring system shall be ~ 5 um (or as best that can be achieved with the machine parameters and commercial equipment) 5 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.23
6.04.06.04
The X-ray pin hole monitor shall provide independent measurement of the energy spread and horizontal/vertical emittance. H=V=15.4 nm
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.24
6.04.06.04
The X-ray pinhole photon beamline shall be equipped with gated cameras that will be employed to provide high resolution turn-by-turn profile measurements
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.25
6.04.06.04
A pinhole assembly including tungsten slits shall provide sufficient resolution to precisely measure the beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.26
6.04.06.04
Several different size pinholes sizes shall be incorporated to allow easy alignment and measurements at different beam currents and energies.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.01
6.04.06.03
Stripline kickers (H & V) shall be used to excite the beam so tunes can be measured using turn-by-turn BPM data.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.02
6.04.06.03
The magnitude of the kick required for the horizontal kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.03
6.04.06.03
The magnitude of the kick required for the vertical kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.04
6.04.06.03
The kicker waveform (risetime and shape) requirements shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.05
6.04.06.03
The location of the tune meter kicker striplines in the ESR shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.06
6.04.06.03
The impedance of the kicker beamline device shall be approved by beam Physics.
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.01
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.03
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.02
6.04.06.03
The transverse feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSSLFB.01
6.04.06.03
The transverse slow feedback system bandwidth shall bs 10 Hz
05/16/2025
In Process
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.2
6.03.04
At the end of the Zigzag there shall be a diagnostic section (details TBD) to measure the bunch length and dP/P.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-DIP.1
6.03.04
The ZigZag section shall consist of a number of dipoles separated by drift spaces in a R56 configuration to increase the bunch length to 40ps.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-QUAD.1
6.03.04
The ZigZag section shall consist of a number of Quadrapoles to control the beam dispersion through the zigzag.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.2
6.03.04
The longitudinal matching section shall consist of a so-called Zigzag section followed by a de-chirp cavity which will stretch the bunch length to 40 ps, reduce the energy spread, and generate a longitudinal phase space rotation of the bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.3
6.03.04
At the Zigzag exit, the electron beam’s average spin orientation shall be longitudinal in the direction of beam travel.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.2
6.03.03
The fast kicker magnet shall follow the rise and fall of the amplitude of the RF sinusoidal functions
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.5
6.03.03
The spin rotator quadrupoles after the Spin rotator solenoid shall be able to match the beam beta functions βx and βy to that required for entry into the 400MeV transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.6
6.03.03
The spin rotator shall ensure the spin direction of the electron bunches are rotated from the longitudinal Z axis to the vertical Y axis.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH.1
6.03.03
The pre-injector LEBT low energy RF section shall transfer the electron beam from the gun to the linac section. shall provide bunching and initial acceleration to each 1 nC bunch
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.4
6.08
The Pre-Injector layout shall accommodate all RF cavities and allow enough room for other Pre-Injector components.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-GUN.2
6.03.04
The pre-injector electron gun shall produce all the bunch patterns required to deliver the ESR beam requirements set forth in [5.9].
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.21
6.03.04
The diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.1
6.03.03
The pre-injector shall have a low energy transfer line from the gun into the beam compression "Bunching" section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.6
6.03.04
Following the gun, there shall be multiple groups of magnets required to control the electron beam.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.7
6.03.04
To characterize and control the fresh bunches the low energy transfer line from the Gun to the Buncher shall contain a plunging transverse profile monitor, a bunch charge monitor, beam loss monitors, and beam position monitors
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-SEP.1
6.03.03
The septum magnet shall be capable of deflecting the incoming electron beam into the RCS and shielding the circulating beam already in the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.3
6.03.03
The vertically spin polarized electron bunch patterns generated by the pre-injector shall be transferred into the RCS unaltered.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.4
6.03.03
The injection system shall be able to inject one bunch per injection kick using RF and magnetic kickers to build up a total of 8 bunches from 4 kicks to the RF and kickers.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.5
6.03.03
The injection system shall ensure the bunch emittance shall match the requirements of the RCS RF system and such, to avoid collective instabilities and to stay within the off-momentum aperture.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.9
6.03.03
The injection system shall contain 3 bump magnets to locally bump the RCS circulating beam close to the injection septum.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.10
6.03.03
The RCS injection system shall contain an RF kicker and a pulsed magnet followed by a septum magnet to redirect the beam into the RCS closed orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.11
6.03.03
The magnetic field of the injection system pulsed magnet shall follow the rise time of the power amplifiers which drive the RF kickers..
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.1
6.08
There shall be a special RF kicker to kick the injected beam into neighboring RF buckets without disturbing the 8 circulating bunches.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.2
6.08
The special kicker shall consist of an RF harmonic kicker with fundamental frequency of 1/4 of the main RCS RF cavity or compatible equivalent alternative.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.3
6.08
The special kicker shall have a rise and fall time that matches the RF bucket size.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.4
6.08
The special kicker shall have a peak power necessary to generate a kick to inject the bunch into the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.5
6.08
The special kicker shall have a macro pulse with a flattop that is greater than the time between the LINAC bunches and shall have a rise and fall time less than 1 RCS turn.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.6
6.08
The special kicker shall be able to repeat at the LINAC pulse rate.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT.28
6.03.03
The LTR transfer line shall have several FODO quadrupoles to control the beta function along the transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ.3
6.03.04
The EIS Pre-Injector shall create bunches which meet the requirements set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-RCS-MAG-QUAD.5
6.03.02
The quadrupoles shall be individually powered with low supplementary current/voltage power supplies for beam-based alignment purposes.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.7
6.03.02
The RCS straight sections shall have the appropirate number of defocusing and focusing quadrupole families per straight section.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.9
6.03.02
The non-colliding straights will have different scheme.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.14
6.03.02
The main arc quadrupoles shall be powered by a total of 2 power circuits 1 for focusing the other defocusing.
05/16/2025
In Process
FALSE

F-EIS-RCS-MAG.15
6.03.02
The quadrupoles in both straight sections shall need a total of 6 power circuits to power all six families of quadrupoles in both straights. (straights are optically identical)
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.18
6.03.02
The RCS magnets shall be fed by a system of power supplies matched in voltage and maximum current to the specifications and requirements of the respective magnets.
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-BUMP.1
6.03.03
the RCS extraction system shall have three fast bump magnets to direct the bunches to the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-FKICK.1
6.03.03
RCS extraction shall be facilitated with a fast kicker having a rise time of 2 micro-secs
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker shall operate in unison with a septum magnet which can direct the beam into the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.1
6.03.03
The beam injection of the electron bunches from the RCS into the ESR ring shall take place in the 12 o’clock straight section.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.2
6.03.03
There will be two electron bunches circulating in the RCS at extraction, these shall be injected into the High Energy Transfer Line which connects the RCS to the ESR.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.1
6.08
The RF system shall Provide a maximum RF voltage of 60MV to accelerate the beam.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.2
6.08
The total RF power provided by the RF amplifiers shall be able to compensate for all additional losses created by the stored electron beam in addition to the acceleration and synchrotron losses.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.3
6.08
The RF system shall Provide sufficient gradient to allow installation of all necessary RF modules in the limited space in IR 10.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.4
6.08
The RF system shall be able to accommodate 4 circulating bunches in one trains of 4 bunches.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.5
6.08
The RF system shall be able to merge the one train of 4 bunches into two larger separate circulating bunches then merge these two large bunches into a single larger circulating bunch.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.6
6.08
The RF system shall be able to accelerate final large, merged bunch to the operating energies needed by the ESR as set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.7
6.03.02
The RF system controls shall be designed to handle the transient beam loading for all bunch structures.
05/16/2025
In Process
FALSE

F-EIS-RCS-VAC.1
6.03.02
The vacuum chamber shall provide sufficient horizontal and vertical aperture to accommodate a beam which is 5 σ larger than the largest sigma beam size determined by the injected RMS emittance.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.2
6.03.02
The average dynamic pressure around the ring shall be < 5e-8[Torr] after 1 year of operation.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.3
6.03.02
The impedance of the entire RCS vacuum system shall allow for the bunch intensities, beam currents, and bunch numbers contained in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.09
6.03.02.04
The vacuum chamber shall be capable of absorbing and carrying away the eddy current power.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.4
6.03.02
The vacuum chamber and all its components shall be designed to withstand the total synchrotron radiation loads seen in operation.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-VAC.08
6.03.02.04
The vacuum chamber shall be capable of absorb synchrotron radiation and carrying away the absorbed power.
05/16/2025
Approved
FALSE

F-EIS-RCS.1
6.03.02
The RCS shall consist of two parts 1. The main RCS Ring, and 2. The High energy transfer line terminating with the ESR injection system
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.2
6.03.03
The RCS shall be capable of accepting the bunches and matching the bunch parameters as injected by the BAR into the LTR transfer line.
05/16/2025
In Process
FALSE

F-EIS-RCS.3
6.03.02
After bunch injection into the RCS, the RCS shall merge the injected bunches into two bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.4
6.03.02
After bunch injection the RCS shall be able to accelerate the single bunch to the final desired energy set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS.5
6.03.02
The RCS needs to accelerate to the top possible energy in a time interval consistent with the parameters set forth in [5.9] at approximately 100 msecs for 18 GeV.
05/16/2025
In Process
FALSE

F-EIS-RCS.6
6.03.03
The RCS shall be capable of kicking the accelerated bunches into the RTE transfer line to the ESR.
05/16/2025
In Process
FALSE

F-EIS-RCS.7
6.03.02
RCS will need to increase the vertical emittance to match the ESR vertical emittance.
05/16/2025
In Process
FALSE

F-EIS-RCS.8
6.03.02
The RCS shall have a racetrack design with 160 arc FODO cells, bending radius of 91.67 m and two 86.624 m straight sections made up of 8 FODO cells with a total circumference of 1.421 km
05/16/2025
In Process
FALSE

F-EIS-RCS.15
6.03.02
The RCS lattice shall contain provisions for correctors such as dipole correctors etc., as needed.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-TLINE-GUN-Diagnostic.1
6.03.04
The Pre-injector separate diagnostic beamline section shall have 3 branches one with Faraday cup, one port containing a connection to the cathode Laser and a line to a low energy beam dump.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.1
6.03.04
The instrumentation in the diagnostic beamline to the low energy beam dump shall have the capability to measure beam position, profile, bunch charge
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.4
6.03.04
The Faraday cup shall be able to measure the charge of the electron bunches from the gun.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-LASER-INST.1
6.03.04
There shall be instrumentation capable of measuring the position and profile of the laser beam on the cathode.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-LASER.1
6.03.04
The laser beam shall illuminate the cathode perpendicular to the cathode face
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.1
6.03.04
The beam tube and flange sizes shall be appropriate to transport polarized e-beam between the e-source and the diagnostic beam line polarimeter chamber.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.2
6.03.04
Vacuum system shall be compatible with UHV requirements.
05/16/2025
Not Applicable
FALSE

F-EIS-TLINE-SPIN.INST.1
6.03.03
Profile monitor, BPM are placed at before, in between and after two Wien filters
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.1
6.03.03
Between the dipole chamber and the bunching section, two Wien filters shall be used as spin rotator to rotate the spin direction from longitudinal to vertical.
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.2
6.03.03
triplets focusing are used in between the two Wien filters to maintain the beam envolop
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.3
6.03.03
Quadpole single let and double let are used before and after Wien to compensate the quadropole components from the Wien entrance and exit
05/16/2025
In Process
FALSE

F-EIS-VAC.1
6.03.04
The EIS vacuum system shall meet UHV standards at a minimum (Ref vacuum spec?)
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.07
6.03.02.04
On 15 m on each side (or one vacuum section) of the SRF cavities the vacuum system shall be processed to class ISO 5.
05/16/2025
Approved
FALSE

F-EIS-VAC.3
6.03.04
The size, location and type of vacuum pumps shall be chosen to meet the required vacuum levels during operation
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-VAC.4
6.03.04
Appropriate vacuum gauging shall be supplied in each vacuum sector to monitor the required vacuum levels
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

G-EIS.6x
6.08
The EIS shall utilize an RF system capable of operating at parameters defined in MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
Not Applicable
FALSE

G-EIS.7
6.03
The EIS shall inject one bunch into the ESR whilst being able to provide 1 bunch per injection cycle.
05/16/2025
Approved
FALSE

F-EIS- PREINJ-LINAC-MAG.1
6.03.04
A Quadrupole triplet shall be installed between each accelerating structure in the LINAC to control the beam beta function and dispersion.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.2
6.03.04
The LINAC Quadrupole triplets shall be optimized to control beams with high RCS injection energies ~ 400[MeV].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.3
6.03.04
In addition to the Quadrupole triplets X Y steering coils shall be installed between each 2.856[GHz] accelerator structure to control the beam beta function and dispersion in the LINAC.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.4
6.03.04
A LINAC XY steering coils shall be optimized to control beams which have low RCS injection energies < < 400[MeV]
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.1
6.03.04
The Pre-Injector S-band LINAC shall be able to accelerate all electron bunches up to the energy's required by [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.2
6.03.04
The Pre-Injector LINAC frequency shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.3
6.03.04
The Pre-Injector LINAC rep-rate shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.1
6.03.02
The instrumentation system shall contain a Beam Position Monitor system consisting of dual-plane Beam Position Monitors adjacent to each quadrupole.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.2
6.03.02
Select Beam Position Monitors in the injection region shall have turn-by-turn orbit measurement capability based on a single, remotely selectable bunch out of the fully filled bunch train to enable injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.3
6.03.02
The instrumentation system shall include a beam current monitor to measure average beam current.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.4
6.03.02
The instrumentation system shall include a system to measure individual bunch charges and bunch pattern.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.5
6.03.02
The instrumentation system shall include a system to measure transverse bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.6
6.03.02
The instrumentation system shall include a system to measure longitudinal bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.7
6.03.02
The instrumentation system shall contain a betatron and synchrotron tune monitors.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.8
6.03.02
The longitudinal bunch profile monitor needs turn-by-turn capability based on a single bunch in the fully filled bunch train to allow timing and energy adjustment for injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.9
6.03.02
The RCS shall contain a beam-based alignment system.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.10
6.03.02
The RCS shall contain a beam loss monitor system at select regions.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.3
6.03.02
The sextupoles shall be sorted into appropriate “families” and powered accordingly.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.4
6.03.02
There shall be dipole correctors capable of adjusting the beam orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.6
6.03.02
The quadrupoles shall generally be arranged in a conventional FODO structure.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.7
6.03.02
Each quadrupole strength needs to be capable of being changed independently by small amounts for beam-based alignment purposes.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.8
6.03.02
Sextupoles shall be sorted into “families” with the family structure dependent on the linear lattice configuration (betatron phase advance per FODO cell).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.9
6.03.02
The maximum integrated field strength of the FODO sextupoles needs to be sufficient to correct chromaticity to within 1 unit in both planes.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.10
6.03.02
Window-frame dipole corrector magnets capable of providing both horizontal and vertical dipole fields to correct the beam orbit in both transverse planes shall be placed adjacent to most of the quadrupoles.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.11
6.03.02
The strength of the window-frame dipole correctors needs to be chosen to correct for any source of orbit distortion and should have a margin for beam based diagnostic purpose.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-GUN-INST.4
6.03.04
To characterize and control the fresh bunches sent to the Mott polarimeter, the gun diagnostic beamline shall contain instrumentation to measure and control the profile, position, and charge of the beam.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-INST.5
6.03.04
The Diagnostic beamline section shall have one Beam Profile Monitor and Wien Filter and an electrostatic bender before the Mott polarimeter and Faraday Cup.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-GUN-INST.6
6.03.04
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

F-EIS-GUN-MAG.1
6.03.04
Following the DC gun, the electron bunch shall be deflected through a bending dipole into the Bunching section
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.2
6.03.04
2 solenoids shall be placed between the gun and the bending dipole into the bunching section capable of correcting the beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.3
6.03.04
Provision shall be made for an appropriate number of air cored steering coils between the Gun and bunching section to correct the electron beam position as required.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.4
6.03.04
A bending dipole shall follow the Gun and be able to bend the beam from the gun into the bunching section OR bend separate electron bunches into the separate diagnostic beam line.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.5
6.03.04
The bending dipole after the gun shall also have the capability to deflect the beam enough to allow a laser to illuminate the photocathode head on.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.6
6.03.04
A minimum of three solenoids shall be placed between the gun and the first bunching cavity to maintain the beam size for 5–10 nC bunches
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.7
6.03.04
Short air core trim coils shall be used to correct beam position for energies greater than 100 keV
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.8
6.03.04
The Diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-VAC.3
6.03.04
The Laser section shall be independent from the Gun\diagnostic section vacuum.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN.3x
6.03.03
The low energy transfer line shall have an additional branch between the Gun and the Bunching section which can transfer individual electron bunches into the diagnostic beamline section.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.4x
6.03.03
The low energy transfer line shall have a laser port between the Gun and the Bunching section which will allow an optical path for the laser to illuminate the cathode face of the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.6x
6.03.04
The gun shall have steering coils to direct the liberated electrons (These can be reused from the existing Gun system.)
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-HETL-ESR-INJ.1
6.03.03
The transferred beam shall meet all the requirements of the circulating beam, for all operational modes of the ESR as set forth in [5.9].
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-INST-BPM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed Beam Position Monitors at the quadrupoles and at the entry and exit of a number of the dipoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-IC.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain FCT and an Integrating Current Transformer before the ESR injection septum.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-PM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed YAG\OTR at the entry and exit of a number of the diploes and quadrupoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-POL.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a system to measure the beam polarization.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-BUMP.1
6.03.03
ESR injection shall have three fast bump magnets to direct the bunches from the HETL into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker of the ESR injector system shall operate in unison with a septum magnet which can direct the beam into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-SLINE-FKICK.1
6.03.03
The ESR injection system shall have a fast strip line kicker with a rise time of 2nsecs .
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.1
6.03.03
The High Energy Transfer Line shall match the beam parameters between the extraction point of the RCS and injection point of the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.2
6.03.03
The extraction into the required High Energy transfer line shall match the ESR bunch spacing and spin pattern.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.3
6.03.03
The High Energy Transfer Line shall be spin transparent.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.4
6.03.03
The ESR extraction system shall have another three bump magnets, its own septum magnet and use the strip line injection kicker to extract and replace the circulating bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BLM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be a bunch length monitor(BLM) at the exit of the 3rd harmonic buncher cavity to measure bunch compression during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam position monitor (BPM) at the entry to the 1st harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section a beam position monitor (BPM) at the entry and exit of the 2nd harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.3
6.03.04
To characterize the beam as it exits the buncher section, beam position monitor(BPM) at the exit of the 3rd harmonic buncher cavity to measure beam position during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-EM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be an emittance monitor(EM), at the exit of the 3rd harmonic buncher cavity to measure beam position, the beam emittance during commissioning.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-EM.01
6.03.04.02.06
Emittances shall be measured using a profile monitor and a dedicated upstream quadrupole configured to measure H, V, and skew profiles.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.03
6.03.04.02.06
The EM shall be able to measure the expected normalized emittance of 40 um
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.02
6.03.04.02.06
Before the 400 MeV beam goes into the spin rotator, the emittance shall be measured by a quad scan
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.04
6.03.04.02.06
Beam emittance shall be measured in the low energy diagnostics beamline using a slit scanner and profile monitor
05/16/2025
On Hold
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.1
6.03.04
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), at the entry and exit of the 2nd harmonic buncher cavity to measure charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.2
6.03.04
To characterize the beam as it exits the buncher section, an integrating current transformer(ICT) at the exit of the 3rd harmonic buncher cavity to measure the bunch charge during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-LM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam loss monitor (BLM) at the entry to the 1st harmonic buncher cavity to measure beam loss
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a transverse profile monitor(TPM) at the entry to the 1st harmonic buncher cavity to measure the charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section there shall be a transverse profile monitor(TPM) at the entry and exit of the 2nd harmonic buncher cavity to measure the bunch profille.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.3
6.03.04
To characterize the beam as it exits the buncher section, transverse profile monitor(TPM) at the exit of the 3rd harmonic buncher cavity the bunch profile during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-MAG-SOL.4
6.03.04
The solenoidal field shall extend to also contain the 1st RF tank of the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-CAV.1
6.08
The LINAC TWP cavities shall be constant gradient cavities
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-INST-CM.1
6.03.04
Bunch charge measurements shall be performed at multiple locations through the LINAC.
05/16/2025
In Process
FALSE

F-EIS-LINAC-INST-PM.1
6.03.04
To measure the beam profile in the LINAC section there shall be a plunging YAG/OTR transverse profile monitor between the 1st and 2nd accelerating cells.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-QUAD.3
6.03.04
A drift space with quadrupole triplets shall be placed between each TWP structure to tune the bunch beta function through the LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.3
6.03.04
Between each S-band LINAC section there shall be at least two window frame steering magnets.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.4
6.03.04
Additionally, window frame steering magnets will be placed at the entry and exit of each accelerating structure to position the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.1
6.03.04
Following the Zigzag there shall be a de-chirp cavity to linearize and reduce the energy spread of the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.1
6.03.04
A longitudinal matching section shall follow the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.1
6.03.03
The fast kicker magnet shall be capable of deflecting the electron beam from the RCS to counter the RF kick.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST-BPM.1
6.03.03
To control the beam through the Spin Rotator section there shall be a Beam Position Monitors placed throughout the spin rotator as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST.1
6.03.03
To measure and control the beam in the medium energy 400 MeV transfer line there shall be sufficient beam position monitors for orbit control, transverse profile monitors, and bunch charge monitors as required.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

F-EIS-METL-MAG-DIP.1
6.03.03
At the entry to the spin rotator section before the spin rotator solenoid there shall be a number of bending dipole to rotate the polarization spin from the Longitudinal direction into the transverse X direction.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-DIP.2
6.03.03
After the exit of spin rotator solenoid, there shall be a number of bending dipoles to close the geometry and direct the beam into the medium energy 400[MeV] transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.4
6.03.03
The spin rotator entry quadrupole shall have at least 2 families this is needed to control the electron beam optics as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.6
6.03.03
The spin rotator exit quadrupoles shall have at least 2 families this is required to control the electron beam optics as needed.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.7
6.03.03
The spin rotator solenoid shall rotate the electron beam spin from the X axis to the vertical y-axis before it enters the medium [400MeV] transport line to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.8
6.03.03
The spin rotator solenoid shall have an integrated gradient of 2.2 [T.m] required to rotate the spin from the horizontal axis to the vertical axis.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.1
6.03.03
The bump magnets shall have a rise and time consistent with the requirements of the circulating bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.2
6.03.03
The Pulsed bump magnets shall be able to create a closed orbit path passing close to the Septum and maintain it during each injection cycle (100-150 Hz).
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.6
6.03.03
Each train of four bunches shall be injected into neighboring RF buckets to facilitate bunch merges.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.7
6.03.03
The injection system shall be capable of maintaining the small spacing required by the injected bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.11
6.03.03
The injection system into the RCS shall be capable of injecting successive bunches into the RCS to create a bunch train with four bunches each circulating in the RCS ready to be merged.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.12
6.03.03
The RCS shall be capable of merging each train of 4 bunches into a larger single bunch to create larger single circulating bunche in the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.1
6.03.03
The Medium energy transfer line shall transfer the beam from the pre-injector longitudinal matching section to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.2
6.03.03
The Medium energy transfer line shall contain 3 sections: 1. Spin rotation section, 2. The main transfer line, 3. The Injector system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.3
6.03.03
There will be number of corrector Quadrupoles after the Pre-Injector longitudinal matching and before the spin rotator to provide beam matching into the Spin Rotator.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.4
6.03.03
The medium energy 400 MeV transfer line shall be able to transport the spin reoriented beam from the spin rotator to the RCS injection system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.5
6.03.03
The medium energy 400 MeV transfer line will maintain the spin direction of the beam along the entire transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH-INST.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be beam position monitor (BPM), and a transverse profile monitor at the entry to the buncher cavity to measure beam loss, position, and charge.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.2
6.06.03
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), beam position monitors and transverse profile monitors
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.3
6.06.03
To characterize the beam as it exits the buncher section, there shall be an emittance measurement including slit and beam viewer, an integrating current transformer, beam position monitor, charge and compression during commissioning.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-RF.1
6.08
one 197 MHz buncher cavity shall be used for providing bunch chirp
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.2
6.08
The bunching section shall generate sufficient compression to compress the bunch length to that required by [5.9].
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.3
6.08
The bunchers rf voltage and phase will be synchronized so that the passing electron bunches meet the required beam characteristics at the end of the buncher section.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-LINAC-VAC.1
6.03.04
The LINAC section shall contain enough strategically located Vacuum gate valves, to allow access to the vacuum volume as needed.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-MAG-QUAD.1
6.03.03
The corrector Quadrupoles shall be able to suppress the βx and βy along the transfer line to levels consistent with those required ate the RCS injection kicker.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.1
6.03.03
The LTR transfer line shall terminate with an injection system capable of transferring the beam into the RCS for all the operating energies and conditions specified in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.2
6.03.03
The injection system shall inject the beam at Need update
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ.1
6.03.04
The EIS Pre-Injector shall consist of 3 sub-systems: 1. An electron gun section, followed by 2. A low energy transfer line and bunching section, followed by 3. A LINAC section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-INST.1
6.03.04
EIS shall have all the beam instrumentation necessary to deliver the operational parameters set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-HETL-INST-BPM-ELEC.01
6.03.03.04.01
The BPM single bunch measurement resolution for a (1 - 4 nC) pilot bunch shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.02
6.03.03.04.01
The BPM single bunch measurement resolution for (5.5 - 28 nC) bunches shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.03
6.03.03.04.01
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.04
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used to measure the transport lattice.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.01
6.03.03.04.01
The BPM Pickup alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.02
6.03.03.04.01
The BPM Pickup shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.04
6.03.03.04.01
The BPM Pickups shall be located by the dipole correctors at every second quadrupole.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM-ELEC.01
6.03.03.04.01
For a (1 nC) pilot bunch, the BPM single bunch measurement resolution shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.02
6.03.03.04.01
For (5.5 - 10 nC) bunches, the BPM single bunch measurement resolution shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.03
6.03.03.04.01
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.04
6.03.03.04.01
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.01
6.03.03.04.01
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.02
6.03.03.04.01
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.04
6.03.03.04.01
The location of the BPM Pickups shall be TBD
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.01
6.03.02.05.04
A synchrotron light monitor (SLM) shall be installed in the RCS ring downstream of an RCS dipole magnet
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.02
6.03.02.05.04
The location of the SLM light extraction port shall be- TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.03
6.03.02.05.04
The synchrotron light shall be transported from the RCS light extraction port to an optical table for detection.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.04
6.03.02.05.04
The synchrotron light optical table shall have a streak camera and gated camera shall be installed.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.05
6.03.02.05.04
The SLM shall be able to make Turn-by-turn measurements using gated cameras to provide measurements of; the injection matching parameters and the beam position stability parameters during acceleration. TBD -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.06
6.03.02.05.04
The SLM shall be used to provide horizontal and vertical transverse profile measurements on bunches with charges > 6nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.07
6.03.02.05.04
The SLM horizontal and vertical transverse profile measurements shall be measured with a resolution in both planes of 0.1 mm
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.08
6.03.02.05.04
The SLM shall be used to provide longitudinal profile measurements
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.09
6.03.02.05.04
A dual sweep streak camera shall be used to provide measurements of the bunch length and longitudinal profiles
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.10
6.03.02.05.04
The dual sweep streak camera shall have a resolution of <5 ps
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.11
6.03.02.05.04
The profile measurements shall be used, together with modeled or measured beam optics to infer the beam emittances and energy spread.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.12
6.03.02.05.04
The Vertical emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.6 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.13
6.03.02.05.04
The Horizontal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 10 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.14
6.03.02.05.04
The Longitudinal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.00001 eV-s
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.15
6.03.02.05.04
The Energy spread measurement, for bunch charges > 6nC, shall be measured with a precision of 0.0001 dp/p
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.01
6.04.06.02
A bunch pattern monitor shall be installed in the ESR to measure indiviual bunch charge with an accuracy 1 %
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.02
6.04.06.02
The Bunch pattern monitor shall be capable of measuring Bunch patterns ranging from a single bunch, to a filled ring with 1,160 bunches
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.01
6.04.06.05
BLM shall be needed to needed to protect sensitive equipment.
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.02
6.04.06.05
The number of BLM installed in the ESR shall be TBD ea
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.03
6.04.06.05
BLM shall be installed at the following locations in the ESR TBD
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.04
6.04.06.05
The sensitivity of the BLM detectors shall be TBD units?
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.05
6.04.06.05
Where possible existing RHIC BLM's can be relocated to identify ESR & HSR losses
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.06
6.04.06.05
The response time from loss detection to abort shall be TBD us
05/16/2025
In Process
FALSE

P-ESR-INST-BPM-ELEC.01
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following capabilities defined for the low intensity pilot injection energies and high intensity collision energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following time resolutions for data refresh defined for the beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.03
6.04.06.01
The ESR BPM Electronics shall have the following time resolutions for data logging defined for the beam energies:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.04
6.04.06.01
The ESR BPM Electronics shall have the following measurement resolutions defined for beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.05
6.04.06.01
The ESR BPM Electronics shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.06
6.04.06.01
The ESR BPM Electronics shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-PU.01
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall provide dual plane (horizontal and vertical) beam positional measurements.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) shall be positioned in the following locations approved by physics as defined in the lattice:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.03
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) mechanical and electrical center in the locations identified shall be:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.04
6.04.06.01
The ESR Beam Position Monitor Pick-Ups housing shall have a +/- 10 (mrad) corresponding to +/- 0.6 (degree) roll tolerance with regards to BPM measurements in respect to the vacuum chamber.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.05
6.04.06.01
The ESR Beam Position Monitor Pick-Ups design shall be less than or equal to the allocated impedance and is within the accepted overall ESR impedance budget approved by physics. (replace with loss factor)
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.06
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall fulfill resolution requirements over the horizontal and vertical beam position range with respect to its fiducials of +/- 3 (mm).
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.07
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to ensure the maximum temperatures of the components (due to heating by the beam) are acceptable for reliability and operations of the EIC over the planned operational life of 20 (yrs).
09/15/2025
In Process
FALSE

P-ESR-INST-BPM-PU.09
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to be baked to 250 °C for UHV processing.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.10
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.11
6.04.06.01
The ESR BPM Pickup shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/30/2025
In Process
FALSE

P-ESR-INST-BPM-PU.12
6.04.06.01
The ESR Beam Position Monitor Button configuration will be mirror symmetric with respect to the mid-and center planes. Deviation from symmetry shall be such that corresponding BPM reading errors are less then 20 microns.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.13
6.04.06.01
The ESR Beam Position Monitor Pick-Ups symmetrical configuration (postion between the four buttons and the relative to the fiducials on top of the button) shall be stable under the inference of the expected operational thermal changes to the extent that corresponding changes in the bpm reading deviate less than 20 µm.
07/25/2025
Approved
FALSE

P-ESR-INST-DCCT.01
6.04.06.02
A DCCT shall measure the average beam current in the ESR.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.02
6.04.06.02
The measurement resolution averaged over 1 sec shall be < 5 uA
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.03
6.04.06.02
The DCCT beamline device impedance shall be approved by beam physics.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.04
6.04.06.02
Measurement drift tolerance (thermal effects) shall be ≤ 1 uA/K
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.05
6.04.06.02
The DCCT sensor in the ring shall operate in the temperature range of 15 to 35 degrees C
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.06
6.04.06.02
The range of average beam current to be measured shall be 0.156x10-3 to 2.5 A
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.07
6.04.06.02
The DCCT system shall have a remote controlled self calibration system
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.08
6.04.06.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.09
6.04.06.02
The measured average current shall be provided to users at a rate of 10 Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.10
6.04.06.02
The measured average current shall be archived at a rate of 10 Hz Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.11
6.04.06.02
The DCCT sensor assembly in the ring shall be radiation resistant
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.01
6.04.06.03
The requirements for longitudinal feedback are ??? TBD
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.02
6.04.06.03
The Longitudinal feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.01
6.04.06.04
The ESR shall have two synchrotron light monitors (SLM) and one X-ray pin hole monitor
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.02
6.04.06.04
The longitudinal bunch profile monitor shall have a turn-by-turn capability based on a single bunch in the fully filled bunch train.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.03
6.04.06.04
TThe SLM systems shall measure the crabbing angle, longitudinal bunch parameters, H & V beam size and global coupling.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.04
6.04.06.04
The SLM shall be able to measure a crabbing angle of 12.5 mrad with accuracy of 10 %
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.05
6.04.06.04
The SLM shall be able to measure the Longitudinal bunch parameters with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.06
6.04.06.04
The SLM shall be able to measure the H & V beam size with accuracy of H=?? V=?? units
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.07
6.04.06.04
The SLM shall be able to measure the Global coupling with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.08
6.04.06.04
One SLM port shall be located downstream of a dipole in an appropriate location in the ESR, exact location not critical.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.09
6.04.06.04
The second SLM port shall be located in a complimentary location in the lattice to ensure all the necessary SLM measurements can be made. TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.10
6.04.06.04
The SLM light extraction port mirrors shall be good quality, having a surface finish better than 1/10 Lambda
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.11
6.04.06.04
The SLM light extraction port mirrors shall be water cooled to avoid image distortion.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.12
6.04.06.04
There shall be an enclosed SL transport from the light extraction port to the SLM optical lab rooms. Length to be determined by the distance to optical lab room, should be minimized to reduce vibration problems.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.13
6.04.06.04
The locations of the SLM optical lab rooms shall be TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.14
6.04.06.04
The double-slit interferometer method shall be used to measure transverse beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.15
6.04.06.04
The standard transverse resolution of an SLM using visible light shall be ~60 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.16
6.04.06.04
The resolution using the double-slit method shall equal to 10 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.17
6.04.06.04
A streak camera shall be used to measure the bunch longitudinal profiles
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.18
6.04.06.04
A position sensitive photo-diode will provide photon beam centroid information which shall supplement the orbit stability measurements by the BPMs
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.19
6.04.06.04
A GigE CCD/CMOS camera, externally triggerable with exposure times ranging from 10 nsec to 5 sec, shall be used to image the visible radiation
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.20
6.04.06.04
A commercially available gated camera with gate width of <2 nsec (compared to a minimum bunch spacing of 10 nsec) shall be used to detect injection oscillations and for beam studies.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.21
6.04.06.04
The location of the X-ray pinhole monitoring system shall be TBD
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.22
6.04.06.04
The target resolution of the X-ray pin hole monitoring system shall be ~ 5 um (or as best that can be achieved with the machine parameters and commercial equipment) 5 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.23
6.04.06.04
The X-ray pin hole monitor shall provide independent measurement of the energy spread and horizontal/vertical emittance. H=V=15.4 nm
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.24
6.04.06.04
The X-ray pinhole photon beamline shall be equipped with gated cameras that will be employed to provide high resolution turn-by-turn profile measurements
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.25
6.04.06.04
A pinhole assembly including tungsten slits shall provide sufficient resolution to precisely measure the beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.26
6.04.06.04
Several different size pinholes sizes shall be incorporated to allow easy alignment and measurements at different beam currents and energies.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.01
6.04.06.03
Stripline kickers (H & V) shall be used to excite the beam so tunes can be measured using turn-by-turn BPM data.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.02
6.04.06.03
The magnitude of the kick required for the horizontal kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.03
6.04.06.03
The magnitude of the kick required for the vertical kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.04
6.04.06.03
The kicker waveform (risetime and shape) requirements shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.05
6.04.06.03
The location of the tune meter kicker striplines in the ESR shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.06
6.04.06.03
The impedance of the kicker beamline device shall be approved by beam Physics.
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.01
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.03
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.02
6.04.06.03
The transverse feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSSLFB.01
6.04.06.03
The transverse slow feedback system bandwidth shall bs 10 Hz
05/16/2025
In Process
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.2
6.03.04
At the end of the Zigzag there shall be a diagnostic section (details TBD) to measure the bunch length and dP/P.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-DIP.1
6.03.04
The ZigZag section shall consist of a number of dipoles separated by drift spaces in a R56 configuration to increase the bunch length to 40ps.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-QUAD.1
6.03.04
The ZigZag section shall consist of a number of Quadrapoles to control the beam dispersion through the zigzag.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.2
6.03.04
The longitudinal matching section shall consist of a so-called Zigzag section followed by a de-chirp cavity which will stretch the bunch length to 40 ps, reduce the energy spread, and generate a longitudinal phase space rotation of the bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.3
6.03.04
At the Zigzag exit, the electron beam’s average spin orientation shall be longitudinal in the direction of beam travel.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.2
6.03.03
The fast kicker magnet shall follow the rise and fall of the amplitude of the RF sinusoidal functions
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.5
6.03.03
The spin rotator quadrupoles after the Spin rotator solenoid shall be able to match the beam beta functions βx and βy to that required for entry into the 400MeV transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.6
6.03.03
The spin rotator shall ensure the spin direction of the electron bunches are rotated from the longitudinal Z axis to the vertical Y axis.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH.1
6.03.03
The pre-injector LEBT low energy RF section shall transfer the electron beam from the gun to the linac section. shall provide bunching and initial acceleration to each 1 nC bunch
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.4
6.08
The Pre-Injector layout shall accommodate all RF cavities and allow enough room for other Pre-Injector components.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-GUN.2
6.03.04
The pre-injector electron gun shall produce all the bunch patterns required to deliver the ESR beam requirements set forth in [5.9].
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.21
6.03.04
The diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.1
6.03.03
The pre-injector shall have a low energy transfer line from the gun into the beam compression "Bunching" section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.6
6.03.04
Following the gun, there shall be multiple groups of magnets required to control the electron beam.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.7
6.03.04
To characterize and control the fresh bunches the low energy transfer line from the Gun to the Buncher shall contain a plunging transverse profile monitor, a bunch charge monitor, beam loss monitors, and beam position monitors
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-SEP.1
6.03.03
The septum magnet shall be capable of deflecting the incoming electron beam into the RCS and shielding the circulating beam already in the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.3
6.03.03
The vertically spin polarized electron bunch patterns generated by the pre-injector shall be transferred into the RCS unaltered.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.4
6.03.03
The injection system shall be able to inject one bunch per injection kick using RF and magnetic kickers to build up a total of 8 bunches from 4 kicks to the RF and kickers.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.5
6.03.03
The injection system shall ensure the bunch emittance shall match the requirements of the RCS RF system and such, to avoid collective instabilities and to stay within the off-momentum aperture.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.9
6.03.03
The injection system shall contain 3 bump magnets to locally bump the RCS circulating beam close to the injection septum.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.10
6.03.03
The RCS injection system shall contain an RF kicker and a pulsed magnet followed by a septum magnet to redirect the beam into the RCS closed orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.11
6.03.03
The magnetic field of the injection system pulsed magnet shall follow the rise time of the power amplifiers which drive the RF kickers..
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.1
6.08
There shall be a special RF kicker to kick the injected beam into neighboring RF buckets without disturbing the 8 circulating bunches.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.2
6.08
The special kicker shall consist of an RF harmonic kicker with fundamental frequency of 1/4 of the main RCS RF cavity or compatible equivalent alternative.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.3
6.08
The special kicker shall have a rise and fall time that matches the RF bucket size.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.4
6.08
The special kicker shall have a peak power necessary to generate a kick to inject the bunch into the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.5
6.08
The special kicker shall have a macro pulse with a flattop that is greater than the time between the LINAC bunches and shall have a rise and fall time less than 1 RCS turn.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.6
6.08
The special kicker shall be able to repeat at the LINAC pulse rate.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT.28
6.03.03
The LTR transfer line shall have several FODO quadrupoles to control the beta function along the transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ.3
6.03.04
The EIS Pre-Injector shall create bunches which meet the requirements set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-RCS-MAG-QUAD.5
6.03.02
The quadrupoles shall be individually powered with low supplementary current/voltage power supplies for beam-based alignment purposes.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.7
6.03.02
The RCS straight sections shall have the appropirate number of defocusing and focusing quadrupole families per straight section.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.9
6.03.02
The non-colliding straights will have different scheme.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.14
6.03.02
The main arc quadrupoles shall be powered by a total of 2 power circuits 1 for focusing the other defocusing.
05/16/2025
In Process
FALSE

F-EIS-RCS-MAG.15
6.03.02
The quadrupoles in both straight sections shall need a total of 6 power circuits to power all six families of quadrupoles in both straights. (straights are optically identical)
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.18
6.03.02
The RCS magnets shall be fed by a system of power supplies matched in voltage and maximum current to the specifications and requirements of the respective magnets.
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-BUMP.1
6.03.03
the RCS extraction system shall have three fast bump magnets to direct the bunches to the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-FKICK.1
6.03.03
RCS extraction shall be facilitated with a fast kicker having a rise time of 2 micro-secs
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker shall operate in unison with a septum magnet which can direct the beam into the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.1
6.03.03
The beam injection of the electron bunches from the RCS into the ESR ring shall take place in the 12 o’clock straight section.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.2
6.03.03
There will be two electron bunches circulating in the RCS at extraction, these shall be injected into the High Energy Transfer Line which connects the RCS to the ESR.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.1
6.08
The RF system shall Provide a maximum RF voltage of 60MV to accelerate the beam.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.2
6.08
The total RF power provided by the RF amplifiers shall be able to compensate for all additional losses created by the stored electron beam in addition to the acceleration and synchrotron losses.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.3
6.08
The RF system shall Provide sufficient gradient to allow installation of all necessary RF modules in the limited space in IR 10.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.4
6.08
The RF system shall be able to accommodate 4 circulating bunches in one trains of 4 bunches.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.5
6.08
The RF system shall be able to merge the one train of 4 bunches into two larger separate circulating bunches then merge these two large bunches into a single larger circulating bunch.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.6
6.08
The RF system shall be able to accelerate final large, merged bunch to the operating energies needed by the ESR as set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.7
6.03.02
The RF system controls shall be designed to handle the transient beam loading for all bunch structures.
05/16/2025
In Process
FALSE

F-EIS-RCS-VAC.1
6.03.02
The vacuum chamber shall provide sufficient horizontal and vertical aperture to accommodate a beam which is 5 σ larger than the largest sigma beam size determined by the injected RMS emittance.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.2
6.03.02
The average dynamic pressure around the ring shall be < 5e-8[Torr] after 1 year of operation.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.3
6.03.02
The impedance of the entire RCS vacuum system shall allow for the bunch intensities, beam currents, and bunch numbers contained in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.09
6.03.02.04
The vacuum chamber shall be capable of absorbing and carrying away the eddy current power.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.4
6.03.02
The vacuum chamber and all its components shall be designed to withstand the total synchrotron radiation loads seen in operation.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-VAC.08
6.03.02.04
The vacuum chamber shall be capable of absorb synchrotron radiation and carrying away the absorbed power.
05/16/2025
Approved
FALSE

F-EIS-RCS.1
6.03.02
The RCS shall consist of two parts 1. The main RCS Ring, and 2. The High energy transfer line terminating with the ESR injection system
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.2
6.03.03
The RCS shall be capable of accepting the bunches and matching the bunch parameters as injected by the BAR into the LTR transfer line.
05/16/2025
In Process
FALSE

F-EIS-RCS.3
6.03.02
After bunch injection into the RCS, the RCS shall merge the injected bunches into two bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.4
6.03.02
After bunch injection the RCS shall be able to accelerate the single bunch to the final desired energy set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS.5
6.03.02
The RCS needs to accelerate to the top possible energy in a time interval consistent with the parameters set forth in [5.9] at approximately 100 msecs for 18 GeV.
05/16/2025
In Process
FALSE

F-EIS-RCS.6
6.03.03
The RCS shall be capable of kicking the accelerated bunches into the RTE transfer line to the ESR.
05/16/2025
In Process
FALSE

F-EIS-RCS.7
6.03.02
RCS will need to increase the vertical emittance to match the ESR vertical emittance.
05/16/2025
In Process
FALSE

F-EIS-RCS.8
6.03.02
The RCS shall have a racetrack design with 160 arc FODO cells, bending radius of 91.67 m and two 86.624 m straight sections made up of 8 FODO cells with a total circumference of 1.421 km
05/16/2025
In Process
FALSE

F-EIS-RCS.15
6.03.02
The RCS lattice shall contain provisions for correctors such as dipole correctors etc., as needed.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-TLINE-GUN-Diagnostic.1
6.03.04
The Pre-injector separate diagnostic beamline section shall have 3 branches one with Faraday cup, one port containing a connection to the cathode Laser and a line to a low energy beam dump.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.1
6.03.04
The instrumentation in the diagnostic beamline to the low energy beam dump shall have the capability to measure beam position, profile, bunch charge
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.4
6.03.04
The Faraday cup shall be able to measure the charge of the electron bunches from the gun.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-LASER-INST.1
6.03.04
There shall be instrumentation capable of measuring the position and profile of the laser beam on the cathode.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-LASER.1
6.03.04
The laser beam shall illuminate the cathode perpendicular to the cathode face
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.1
6.03.04
The beam tube and flange sizes shall be appropriate to transport polarized e-beam between the e-source and the diagnostic beam line polarimeter chamber.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.2
6.03.04
Vacuum system shall be compatible with UHV requirements.
05/16/2025
Not Applicable
FALSE

F-EIS-TLINE-SPIN.INST.1
6.03.03
Profile monitor, BPM are placed at before, in between and after two Wien filters
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.1
6.03.03
Between the dipole chamber and the bunching section, two Wien filters shall be used as spin rotator to rotate the spin direction from longitudinal to vertical.
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.2
6.03.03
triplets focusing are used in between the two Wien filters to maintain the beam envolop
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.3
6.03.03
Quadpole single let and double let are used before and after Wien to compensate the quadropole components from the Wien entrance and exit
05/16/2025
In Process
FALSE

F-EIS-VAC.1
6.03.04
The EIS vacuum system shall meet UHV standards at a minimum (Ref vacuum spec?)
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.07
6.03.02.04
On 15 m on each side (or one vacuum section) of the SRF cavities the vacuum system shall be processed to class ISO 5.
05/16/2025
Approved
FALSE

F-EIS-VAC.3
6.03.04
The size, location and type of vacuum pumps shall be chosen to meet the required vacuum levels during operation
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-VAC.4
6.03.04
Appropriate vacuum gauging shall be supplied in each vacuum sector to monitor the required vacuum levels
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

G-EIS.8
6.03
The EIS shall provide an electron beam to the ESR having RMS Bunch lengths at extraction to meet beam requirements as set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
Approved
FALSE

F-EIS- PREINJ-LINAC-MAG.1
6.03.04
A Quadrupole triplet shall be installed between each accelerating structure in the LINAC to control the beam beta function and dispersion.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.2
6.03.04
The LINAC Quadrupole triplets shall be optimized to control beams with high RCS injection energies ~ 400[MeV].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.3
6.03.04
In addition to the Quadrupole triplets X Y steering coils shall be installed between each 2.856[GHz] accelerator structure to control the beam beta function and dispersion in the LINAC.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.4
6.03.04
A LINAC XY steering coils shall be optimized to control beams which have low RCS injection energies < < 400[MeV]
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.1
6.03.04
The Pre-Injector S-band LINAC shall be able to accelerate all electron bunches up to the energy's required by [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.2
6.03.04
The Pre-Injector LINAC frequency shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.3
6.03.04
The Pre-Injector LINAC rep-rate shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.1
6.03.02
The instrumentation system shall contain a Beam Position Monitor system consisting of dual-plane Beam Position Monitors adjacent to each quadrupole.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.2
6.03.02
Select Beam Position Monitors in the injection region shall have turn-by-turn orbit measurement capability based on a single, remotely selectable bunch out of the fully filled bunch train to enable injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.3
6.03.02
The instrumentation system shall include a beam current monitor to measure average beam current.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.4
6.03.02
The instrumentation system shall include a system to measure individual bunch charges and bunch pattern.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.5
6.03.02
The instrumentation system shall include a system to measure transverse bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.6
6.03.02
The instrumentation system shall include a system to measure longitudinal bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.7
6.03.02
The instrumentation system shall contain a betatron and synchrotron tune monitors.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.8
6.03.02
The longitudinal bunch profile monitor needs turn-by-turn capability based on a single bunch in the fully filled bunch train to allow timing and energy adjustment for injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.9
6.03.02
The RCS shall contain a beam-based alignment system.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.10
6.03.02
The RCS shall contain a beam loss monitor system at select regions.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.3
6.03.02
The sextupoles shall be sorted into appropriate “families” and powered accordingly.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.4
6.03.02
There shall be dipole correctors capable of adjusting the beam orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.6
6.03.02
The quadrupoles shall generally be arranged in a conventional FODO structure.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.7
6.03.02
Each quadrupole strength needs to be capable of being changed independently by small amounts for beam-based alignment purposes.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.8
6.03.02
Sextupoles shall be sorted into “families” with the family structure dependent on the linear lattice configuration (betatron phase advance per FODO cell).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.9
6.03.02
The maximum integrated field strength of the FODO sextupoles needs to be sufficient to correct chromaticity to within 1 unit in both planes.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.10
6.03.02
Window-frame dipole corrector magnets capable of providing both horizontal and vertical dipole fields to correct the beam orbit in both transverse planes shall be placed adjacent to most of the quadrupoles.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.11
6.03.02
The strength of the window-frame dipole correctors needs to be chosen to correct for any source of orbit distortion and should have a margin for beam based diagnostic purpose.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-GUN-INST.4
6.03.04
To characterize and control the fresh bunches sent to the Mott polarimeter, the gun diagnostic beamline shall contain instrumentation to measure and control the profile, position, and charge of the beam.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-INST.5
6.03.04
The Diagnostic beamline section shall have one Beam Profile Monitor and Wien Filter and an electrostatic bender before the Mott polarimeter and Faraday Cup.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-GUN-INST.6
6.03.04
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

F-EIS-GUN-MAG.1
6.03.04
Following the DC gun, the electron bunch shall be deflected through a bending dipole into the Bunching section
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.2
6.03.04
2 solenoids shall be placed between the gun and the bending dipole into the bunching section capable of correcting the beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.3
6.03.04
Provision shall be made for an appropriate number of air cored steering coils between the Gun and bunching section to correct the electron beam position as required.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.4
6.03.04
A bending dipole shall follow the Gun and be able to bend the beam from the gun into the bunching section OR bend separate electron bunches into the separate diagnostic beam line.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.5
6.03.04
The bending dipole after the gun shall also have the capability to deflect the beam enough to allow a laser to illuminate the photocathode head on.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.6
6.03.04
A minimum of three solenoids shall be placed between the gun and the first bunching cavity to maintain the beam size for 5–10 nC bunches
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.7
6.03.04
Short air core trim coils shall be used to correct beam position for energies greater than 100 keV
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.8
6.03.04
The Diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-VAC.3
6.03.04
The Laser section shall be independent from the Gun\diagnostic section vacuum.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN.3x
6.03.03
The low energy transfer line shall have an additional branch between the Gun and the Bunching section which can transfer individual electron bunches into the diagnostic beamline section.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.4x
6.03.03
The low energy transfer line shall have a laser port between the Gun and the Bunching section which will allow an optical path for the laser to illuminate the cathode face of the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.6x
6.03.04
The gun shall have steering coils to direct the liberated electrons (These can be reused from the existing Gun system.)
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-HETL-ESR-INJ.1
6.03.03
The transferred beam shall meet all the requirements of the circulating beam, for all operational modes of the ESR as set forth in [5.9].
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-INST-BPM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed Beam Position Monitors at the quadrupoles and at the entry and exit of a number of the dipoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-IC.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain FCT and an Integrating Current Transformer before the ESR injection septum.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-PM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed YAG\OTR at the entry and exit of a number of the diploes and quadrupoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-POL.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a system to measure the beam polarization.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-BUMP.1
6.03.03
ESR injection shall have three fast bump magnets to direct the bunches from the HETL into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker of the ESR injector system shall operate in unison with a septum magnet which can direct the beam into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-SLINE-FKICK.1
6.03.03
The ESR injection system shall have a fast strip line kicker with a rise time of 2nsecs .
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.1
6.03.03
The High Energy Transfer Line shall match the beam parameters between the extraction point of the RCS and injection point of the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.2
6.03.03
The extraction into the required High Energy transfer line shall match the ESR bunch spacing and spin pattern.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.3
6.03.03
The High Energy Transfer Line shall be spin transparent.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.4
6.03.03
The ESR extraction system shall have another three bump magnets, its own septum magnet and use the strip line injection kicker to extract and replace the circulating bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BLM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be a bunch length monitor(BLM) at the exit of the 3rd harmonic buncher cavity to measure bunch compression during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam position monitor (BPM) at the entry to the 1st harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section a beam position monitor (BPM) at the entry and exit of the 2nd harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.3
6.03.04
To characterize the beam as it exits the buncher section, beam position monitor(BPM) at the exit of the 3rd harmonic buncher cavity to measure beam position during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-EM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be an emittance monitor(EM), at the exit of the 3rd harmonic buncher cavity to measure beam position, the beam emittance during commissioning.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-EM.01
6.03.04.02.06
Emittances shall be measured using a profile monitor and a dedicated upstream quadrupole configured to measure H, V, and skew profiles.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.03
6.03.04.02.06
The EM shall be able to measure the expected normalized emittance of 40 um
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.02
6.03.04.02.06
Before the 400 MeV beam goes into the spin rotator, the emittance shall be measured by a quad scan
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.04
6.03.04.02.06
Beam emittance shall be measured in the low energy diagnostics beamline using a slit scanner and profile monitor
05/16/2025
On Hold
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.1
6.03.04
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), at the entry and exit of the 2nd harmonic buncher cavity to measure charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.2
6.03.04
To characterize the beam as it exits the buncher section, an integrating current transformer(ICT) at the exit of the 3rd harmonic buncher cavity to measure the bunch charge during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-LM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam loss monitor (BLM) at the entry to the 1st harmonic buncher cavity to measure beam loss
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a transverse profile monitor(TPM) at the entry to the 1st harmonic buncher cavity to measure the charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section there shall be a transverse profile monitor(TPM) at the entry and exit of the 2nd harmonic buncher cavity to measure the bunch profille.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.3
6.03.04
To characterize the beam as it exits the buncher section, transverse profile monitor(TPM) at the exit of the 3rd harmonic buncher cavity the bunch profile during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-MAG-SOL.4
6.03.04
The solenoidal field shall extend to also contain the 1st RF tank of the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-CAV.1
6.08
The LINAC TWP cavities shall be constant gradient cavities
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-INST-CM.1
6.03.04
Bunch charge measurements shall be performed at multiple locations through the LINAC.
05/16/2025
In Process
FALSE

F-EIS-LINAC-INST-PM.1
6.03.04
To measure the beam profile in the LINAC section there shall be a plunging YAG/OTR transverse profile monitor between the 1st and 2nd accelerating cells.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-QUAD.3
6.03.04
A drift space with quadrupole triplets shall be placed between each TWP structure to tune the bunch beta function through the LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.3
6.03.04
Between each S-band LINAC section there shall be at least two window frame steering magnets.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.4
6.03.04
Additionally, window frame steering magnets will be placed at the entry and exit of each accelerating structure to position the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.1
6.03.04
Following the Zigzag there shall be a de-chirp cavity to linearize and reduce the energy spread of the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.1
6.03.04
A longitudinal matching section shall follow the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.1
6.03.03
The fast kicker magnet shall be capable of deflecting the electron beam from the RCS to counter the RF kick.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST-BPM.1
6.03.03
To control the beam through the Spin Rotator section there shall be a Beam Position Monitors placed throughout the spin rotator as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST.1
6.03.03
To measure and control the beam in the medium energy 400 MeV transfer line there shall be sufficient beam position monitors for orbit control, transverse profile monitors, and bunch charge monitors as required.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

F-EIS-METL-MAG-DIP.1
6.03.03
At the entry to the spin rotator section before the spin rotator solenoid there shall be a number of bending dipole to rotate the polarization spin from the Longitudinal direction into the transverse X direction.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-DIP.2
6.03.03
After the exit of spin rotator solenoid, there shall be a number of bending dipoles to close the geometry and direct the beam into the medium energy 400[MeV] transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.4
6.03.03
The spin rotator entry quadrupole shall have at least 2 families this is needed to control the electron beam optics as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.6
6.03.03
The spin rotator exit quadrupoles shall have at least 2 families this is required to control the electron beam optics as needed.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.7
6.03.03
The spin rotator solenoid shall rotate the electron beam spin from the X axis to the vertical y-axis before it enters the medium [400MeV] transport line to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.8
6.03.03
The spin rotator solenoid shall have an integrated gradient of 2.2 [T.m] required to rotate the spin from the horizontal axis to the vertical axis.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.1
6.03.03
The bump magnets shall have a rise and time consistent with the requirements of the circulating bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.2
6.03.03
The Pulsed bump magnets shall be able to create a closed orbit path passing close to the Septum and maintain it during each injection cycle (100-150 Hz).
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.6
6.03.03
Each train of four bunches shall be injected into neighboring RF buckets to facilitate bunch merges.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.7
6.03.03
The injection system shall be capable of maintaining the small spacing required by the injected bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.11
6.03.03
The injection system into the RCS shall be capable of injecting successive bunches into the RCS to create a bunch train with four bunches each circulating in the RCS ready to be merged.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.12
6.03.03
The RCS shall be capable of merging each train of 4 bunches into a larger single bunch to create larger single circulating bunche in the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.1
6.03.03
The Medium energy transfer line shall transfer the beam from the pre-injector longitudinal matching section to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.2
6.03.03
The Medium energy transfer line shall contain 3 sections: 1. Spin rotation section, 2. The main transfer line, 3. The Injector system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.3
6.03.03
There will be number of corrector Quadrupoles after the Pre-Injector longitudinal matching and before the spin rotator to provide beam matching into the Spin Rotator.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.4
6.03.03
The medium energy 400 MeV transfer line shall be able to transport the spin reoriented beam from the spin rotator to the RCS injection system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.5
6.03.03
The medium energy 400 MeV transfer line will maintain the spin direction of the beam along the entire transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH-INST.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be beam position monitor (BPM), and a transverse profile monitor at the entry to the buncher cavity to measure beam loss, position, and charge.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.2
6.06.03
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), beam position monitors and transverse profile monitors
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.3
6.06.03
To characterize the beam as it exits the buncher section, there shall be an emittance measurement including slit and beam viewer, an integrating current transformer, beam position monitor, charge and compression during commissioning.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-RF.1
6.08
one 197 MHz buncher cavity shall be used for providing bunch chirp
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.2
6.08
The bunching section shall generate sufficient compression to compress the bunch length to that required by [5.9].
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.3
6.08
The bunchers rf voltage and phase will be synchronized so that the passing electron bunches meet the required beam characteristics at the end of the buncher section.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-LINAC-VAC.1
6.03.04
The LINAC section shall contain enough strategically located Vacuum gate valves, to allow access to the vacuum volume as needed.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-MAG-QUAD.1
6.03.03
The corrector Quadrupoles shall be able to suppress the βx and βy along the transfer line to levels consistent with those required ate the RCS injection kicker.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.1
6.03.03
The LTR transfer line shall terminate with an injection system capable of transferring the beam into the RCS for all the operating energies and conditions specified in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.2
6.03.03
The injection system shall inject the beam at Need update
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ.1
6.03.04
The EIS Pre-Injector shall consist of 3 sub-systems: 1. An electron gun section, followed by 2. A low energy transfer line and bunching section, followed by 3. A LINAC section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-INST.1
6.03.04
EIS shall have all the beam instrumentation necessary to deliver the operational parameters set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-HETL-INST-BPM-ELEC.01
6.03.03.04.01
The BPM single bunch measurement resolution for a (1 - 4 nC) pilot bunch shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.02
6.03.03.04.01
The BPM single bunch measurement resolution for (5.5 - 28 nC) bunches shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.03
6.03.03.04.01
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.04
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used to measure the transport lattice.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.01
6.03.03.04.01
The BPM Pickup alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.02
6.03.03.04.01
The BPM Pickup shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.04
6.03.03.04.01
The BPM Pickups shall be located by the dipole correctors at every second quadrupole.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM-ELEC.01
6.03.03.04.01
For a (1 nC) pilot bunch, the BPM single bunch measurement resolution shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.02
6.03.03.04.01
For (5.5 - 10 nC) bunches, the BPM single bunch measurement resolution shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.03
6.03.03.04.01
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.04
6.03.03.04.01
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.01
6.03.03.04.01
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.02
6.03.03.04.01
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.04
6.03.03.04.01
The location of the BPM Pickups shall be TBD
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.01
6.03.02.05.04
A synchrotron light monitor (SLM) shall be installed in the RCS ring downstream of an RCS dipole magnet
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.02
6.03.02.05.04
The location of the SLM light extraction port shall be- TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.03
6.03.02.05.04
The synchrotron light shall be transported from the RCS light extraction port to an optical table for detection.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.04
6.03.02.05.04
The synchrotron light optical table shall have a streak camera and gated camera shall be installed.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.05
6.03.02.05.04
The SLM shall be able to make Turn-by-turn measurements using gated cameras to provide measurements of; the injection matching parameters and the beam position stability parameters during acceleration. TBD -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.06
6.03.02.05.04
The SLM shall be used to provide horizontal and vertical transverse profile measurements on bunches with charges > 6nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.07
6.03.02.05.04
The SLM horizontal and vertical transverse profile measurements shall be measured with a resolution in both planes of 0.1 mm
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.08
6.03.02.05.04
The SLM shall be used to provide longitudinal profile measurements
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.09
6.03.02.05.04
A dual sweep streak camera shall be used to provide measurements of the bunch length and longitudinal profiles
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.10
6.03.02.05.04
The dual sweep streak camera shall have a resolution of <5 ps
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.11
6.03.02.05.04
The profile measurements shall be used, together with modeled or measured beam optics to infer the beam emittances and energy spread.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.12
6.03.02.05.04
The Vertical emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.6 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.13
6.03.02.05.04
The Horizontal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 10 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.14
6.03.02.05.04
The Longitudinal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.00001 eV-s
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.15
6.03.02.05.04
The Energy spread measurement, for bunch charges > 6nC, shall be measured with a precision of 0.0001 dp/p
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.01
6.04.06.02
A bunch pattern monitor shall be installed in the ESR to measure indiviual bunch charge with an accuracy 1 %
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.02
6.04.06.02
The Bunch pattern monitor shall be capable of measuring Bunch patterns ranging from a single bunch, to a filled ring with 1,160 bunches
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.01
6.04.06.05
BLM shall be needed to needed to protect sensitive equipment.
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.02
6.04.06.05
The number of BLM installed in the ESR shall be TBD ea
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.03
6.04.06.05
BLM shall be installed at the following locations in the ESR TBD
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.04
6.04.06.05
The sensitivity of the BLM detectors shall be TBD units?
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.05
6.04.06.05
Where possible existing RHIC BLM's can be relocated to identify ESR & HSR losses
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.06
6.04.06.05
The response time from loss detection to abort shall be TBD us
05/16/2025
In Process
FALSE

P-ESR-INST-BPM-ELEC.01
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following capabilities defined for the low intensity pilot injection energies and high intensity collision energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following time resolutions for data refresh defined for the beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.03
6.04.06.01
The ESR BPM Electronics shall have the following time resolutions for data logging defined for the beam energies:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.04
6.04.06.01
The ESR BPM Electronics shall have the following measurement resolutions defined for beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.05
6.04.06.01
The ESR BPM Electronics shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.06
6.04.06.01
The ESR BPM Electronics shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-PU.01
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall provide dual plane (horizontal and vertical) beam positional measurements.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) shall be positioned in the following locations approved by physics as defined in the lattice:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.03
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) mechanical and electrical center in the locations identified shall be:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.04
6.04.06.01
The ESR Beam Position Monitor Pick-Ups housing shall have a +/- 10 (mrad) corresponding to +/- 0.6 (degree) roll tolerance with regards to BPM measurements in respect to the vacuum chamber.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.05
6.04.06.01
The ESR Beam Position Monitor Pick-Ups design shall be less than or equal to the allocated impedance and is within the accepted overall ESR impedance budget approved by physics. (replace with loss factor)
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.06
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall fulfill resolution requirements over the horizontal and vertical beam position range with respect to its fiducials of +/- 3 (mm).
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.07
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to ensure the maximum temperatures of the components (due to heating by the beam) are acceptable for reliability and operations of the EIC over the planned operational life of 20 (yrs).
09/15/2025
In Process
FALSE

P-ESR-INST-BPM-PU.09
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to be baked to 250 °C for UHV processing.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.10
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.11
6.04.06.01
The ESR BPM Pickup shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/30/2025
In Process
FALSE

P-ESR-INST-BPM-PU.12
6.04.06.01
The ESR Beam Position Monitor Button configuration will be mirror symmetric with respect to the mid-and center planes. Deviation from symmetry shall be such that corresponding BPM reading errors are less then 20 microns.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.13
6.04.06.01
The ESR Beam Position Monitor Pick-Ups symmetrical configuration (postion between the four buttons and the relative to the fiducials on top of the button) shall be stable under the inference of the expected operational thermal changes to the extent that corresponding changes in the bpm reading deviate less than 20 µm.
07/25/2025
Approved
FALSE

P-ESR-INST-DCCT.01
6.04.06.02
A DCCT shall measure the average beam current in the ESR.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.02
6.04.06.02
The measurement resolution averaged over 1 sec shall be < 5 uA
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.03
6.04.06.02
The DCCT beamline device impedance shall be approved by beam physics.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.04
6.04.06.02
Measurement drift tolerance (thermal effects) shall be ≤ 1 uA/K
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.05
6.04.06.02
The DCCT sensor in the ring shall operate in the temperature range of 15 to 35 degrees C
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.06
6.04.06.02
The range of average beam current to be measured shall be 0.156x10-3 to 2.5 A
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.07
6.04.06.02
The DCCT system shall have a remote controlled self calibration system
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.08
6.04.06.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.09
6.04.06.02
The measured average current shall be provided to users at a rate of 10 Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.10
6.04.06.02
The measured average current shall be archived at a rate of 10 Hz Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.11
6.04.06.02
The DCCT sensor assembly in the ring shall be radiation resistant
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.01
6.04.06.03
The requirements for longitudinal feedback are ??? TBD
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.02
6.04.06.03
The Longitudinal feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.01
6.04.06.04
The ESR shall have two synchrotron light monitors (SLM) and one X-ray pin hole monitor
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.02
6.04.06.04
The longitudinal bunch profile monitor shall have a turn-by-turn capability based on a single bunch in the fully filled bunch train.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.03
6.04.06.04
TThe SLM systems shall measure the crabbing angle, longitudinal bunch parameters, H & V beam size and global coupling.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.04
6.04.06.04
The SLM shall be able to measure a crabbing angle of 12.5 mrad with accuracy of 10 %
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.05
6.04.06.04
The SLM shall be able to measure the Longitudinal bunch parameters with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.06
6.04.06.04
The SLM shall be able to measure the H & V beam size with accuracy of H=?? V=?? units
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.07
6.04.06.04
The SLM shall be able to measure the Global coupling with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.08
6.04.06.04
One SLM port shall be located downstream of a dipole in an appropriate location in the ESR, exact location not critical.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.09
6.04.06.04
The second SLM port shall be located in a complimentary location in the lattice to ensure all the necessary SLM measurements can be made. TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.10
6.04.06.04
The SLM light extraction port mirrors shall be good quality, having a surface finish better than 1/10 Lambda
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.11
6.04.06.04
The SLM light extraction port mirrors shall be water cooled to avoid image distortion.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.12
6.04.06.04
There shall be an enclosed SL transport from the light extraction port to the SLM optical lab rooms. Length to be determined by the distance to optical lab room, should be minimized to reduce vibration problems.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.13
6.04.06.04
The locations of the SLM optical lab rooms shall be TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.14
6.04.06.04
The double-slit interferometer method shall be used to measure transverse beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.15
6.04.06.04
The standard transverse resolution of an SLM using visible light shall be ~60 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.16
6.04.06.04
The resolution using the double-slit method shall equal to 10 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.17
6.04.06.04
A streak camera shall be used to measure the bunch longitudinal profiles
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.18
6.04.06.04
A position sensitive photo-diode will provide photon beam centroid information which shall supplement the orbit stability measurements by the BPMs
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.19
6.04.06.04
A GigE CCD/CMOS camera, externally triggerable with exposure times ranging from 10 nsec to 5 sec, shall be used to image the visible radiation
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.20
6.04.06.04
A commercially available gated camera with gate width of <2 nsec (compared to a minimum bunch spacing of 10 nsec) shall be used to detect injection oscillations and for beam studies.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.21
6.04.06.04
The location of the X-ray pinhole monitoring system shall be TBD
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.22
6.04.06.04
The target resolution of the X-ray pin hole monitoring system shall be ~ 5 um (or as best that can be achieved with the machine parameters and commercial equipment) 5 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.23
6.04.06.04
The X-ray pin hole monitor shall provide independent measurement of the energy spread and horizontal/vertical emittance. H=V=15.4 nm
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.24
6.04.06.04
The X-ray pinhole photon beamline shall be equipped with gated cameras that will be employed to provide high resolution turn-by-turn profile measurements
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.25
6.04.06.04
A pinhole assembly including tungsten slits shall provide sufficient resolution to precisely measure the beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.26
6.04.06.04
Several different size pinholes sizes shall be incorporated to allow easy alignment and measurements at different beam currents and energies.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.01
6.04.06.03
Stripline kickers (H & V) shall be used to excite the beam so tunes can be measured using turn-by-turn BPM data.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.02
6.04.06.03
The magnitude of the kick required for the horizontal kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.03
6.04.06.03
The magnitude of the kick required for the vertical kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.04
6.04.06.03
The kicker waveform (risetime and shape) requirements shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.05
6.04.06.03
The location of the tune meter kicker striplines in the ESR shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.06
6.04.06.03
The impedance of the kicker beamline device shall be approved by beam Physics.
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.01
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.03
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.02
6.04.06.03
The transverse feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSSLFB.01
6.04.06.03
The transverse slow feedback system bandwidth shall bs 10 Hz
05/16/2025
In Process
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.2
6.03.04
At the end of the Zigzag there shall be a diagnostic section (details TBD) to measure the bunch length and dP/P.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-DIP.1
6.03.04
The ZigZag section shall consist of a number of dipoles separated by drift spaces in a R56 configuration to increase the bunch length to 40ps.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-QUAD.1
6.03.04
The ZigZag section shall consist of a number of Quadrapoles to control the beam dispersion through the zigzag.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.2
6.03.04
The longitudinal matching section shall consist of a so-called Zigzag section followed by a de-chirp cavity which will stretch the bunch length to 40 ps, reduce the energy spread, and generate a longitudinal phase space rotation of the bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.3
6.03.04
At the Zigzag exit, the electron beam’s average spin orientation shall be longitudinal in the direction of beam travel.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.2
6.03.03
The fast kicker magnet shall follow the rise and fall of the amplitude of the RF sinusoidal functions
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.5
6.03.03
The spin rotator quadrupoles after the Spin rotator solenoid shall be able to match the beam beta functions βx and βy to that required for entry into the 400MeV transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.6
6.03.03
The spin rotator shall ensure the spin direction of the electron bunches are rotated from the longitudinal Z axis to the vertical Y axis.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH.1
6.03.03
The pre-injector LEBT low energy RF section shall transfer the electron beam from the gun to the linac section. shall provide bunching and initial acceleration to each 1 nC bunch
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.4
6.08
The Pre-Injector layout shall accommodate all RF cavities and allow enough room for other Pre-Injector components.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-GUN.2
6.03.04
The pre-injector electron gun shall produce all the bunch patterns required to deliver the ESR beam requirements set forth in [5.9].
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.21
6.03.04
The diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.1
6.03.03
The pre-injector shall have a low energy transfer line from the gun into the beam compression "Bunching" section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.6
6.03.04
Following the gun, there shall be multiple groups of magnets required to control the electron beam.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.7
6.03.04
To characterize and control the fresh bunches the low energy transfer line from the Gun to the Buncher shall contain a plunging transverse profile monitor, a bunch charge monitor, beam loss monitors, and beam position monitors
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-SEP.1
6.03.03
The septum magnet shall be capable of deflecting the incoming electron beam into the RCS and shielding the circulating beam already in the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.3
6.03.03
The vertically spin polarized electron bunch patterns generated by the pre-injector shall be transferred into the RCS unaltered.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.4
6.03.03
The injection system shall be able to inject one bunch per injection kick using RF and magnetic kickers to build up a total of 8 bunches from 4 kicks to the RF and kickers.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.5
6.03.03
The injection system shall ensure the bunch emittance shall match the requirements of the RCS RF system and such, to avoid collective instabilities and to stay within the off-momentum aperture.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.9
6.03.03
The injection system shall contain 3 bump magnets to locally bump the RCS circulating beam close to the injection septum.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.10
6.03.03
The RCS injection system shall contain an RF kicker and a pulsed magnet followed by a septum magnet to redirect the beam into the RCS closed orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.11
6.03.03
The magnetic field of the injection system pulsed magnet shall follow the rise time of the power amplifiers which drive the RF kickers..
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.1
6.08
There shall be a special RF kicker to kick the injected beam into neighboring RF buckets without disturbing the 8 circulating bunches.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.2
6.08
The special kicker shall consist of an RF harmonic kicker with fundamental frequency of 1/4 of the main RCS RF cavity or compatible equivalent alternative.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.3
6.08
The special kicker shall have a rise and fall time that matches the RF bucket size.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.4
6.08
The special kicker shall have a peak power necessary to generate a kick to inject the bunch into the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.5
6.08
The special kicker shall have a macro pulse with a flattop that is greater than the time between the LINAC bunches and shall have a rise and fall time less than 1 RCS turn.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.6
6.08
The special kicker shall be able to repeat at the LINAC pulse rate.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT.28
6.03.03
The LTR transfer line shall have several FODO quadrupoles to control the beta function along the transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ.3
6.03.04
The EIS Pre-Injector shall create bunches which meet the requirements set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-RCS-MAG-QUAD.5
6.03.02
The quadrupoles shall be individually powered with low supplementary current/voltage power supplies for beam-based alignment purposes.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.7
6.03.02
The RCS straight sections shall have the appropirate number of defocusing and focusing quadrupole families per straight section.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.9
6.03.02
The non-colliding straights will have different scheme.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.14
6.03.02
The main arc quadrupoles shall be powered by a total of 2 power circuits 1 for focusing the other defocusing.
05/16/2025
In Process
FALSE

F-EIS-RCS-MAG.15
6.03.02
The quadrupoles in both straight sections shall need a total of 6 power circuits to power all six families of quadrupoles in both straights. (straights are optically identical)
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.18
6.03.02
The RCS magnets shall be fed by a system of power supplies matched in voltage and maximum current to the specifications and requirements of the respective magnets.
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-BUMP.1
6.03.03
the RCS extraction system shall have three fast bump magnets to direct the bunches to the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-FKICK.1
6.03.03
RCS extraction shall be facilitated with a fast kicker having a rise time of 2 micro-secs
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker shall operate in unison with a septum magnet which can direct the beam into the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.1
6.03.03
The beam injection of the electron bunches from the RCS into the ESR ring shall take place in the 12 o’clock straight section.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.2
6.03.03
There will be two electron bunches circulating in the RCS at extraction, these shall be injected into the High Energy Transfer Line which connects the RCS to the ESR.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.1
6.08
The RF system shall Provide a maximum RF voltage of 60MV to accelerate the beam.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.2
6.08
The total RF power provided by the RF amplifiers shall be able to compensate for all additional losses created by the stored electron beam in addition to the acceleration and synchrotron losses.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.3
6.08
The RF system shall Provide sufficient gradient to allow installation of all necessary RF modules in the limited space in IR 10.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.4
6.08
The RF system shall be able to accommodate 4 circulating bunches in one trains of 4 bunches.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.5
6.08
The RF system shall be able to merge the one train of 4 bunches into two larger separate circulating bunches then merge these two large bunches into a single larger circulating bunch.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.6
6.08
The RF system shall be able to accelerate final large, merged bunch to the operating energies needed by the ESR as set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.7
6.03.02
The RF system controls shall be designed to handle the transient beam loading for all bunch structures.
05/16/2025
In Process
FALSE

F-EIS-RCS-VAC.1
6.03.02
The vacuum chamber shall provide sufficient horizontal and vertical aperture to accommodate a beam which is 5 σ larger than the largest sigma beam size determined by the injected RMS emittance.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.2
6.03.02
The average dynamic pressure around the ring shall be < 5e-8[Torr] after 1 year of operation.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.3
6.03.02
The impedance of the entire RCS vacuum system shall allow for the bunch intensities, beam currents, and bunch numbers contained in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.09
6.03.02.04
The vacuum chamber shall be capable of absorbing and carrying away the eddy current power.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.4
6.03.02
The vacuum chamber and all its components shall be designed to withstand the total synchrotron radiation loads seen in operation.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-VAC.08
6.03.02.04
The vacuum chamber shall be capable of absorb synchrotron radiation and carrying away the absorbed power.
05/16/2025
Approved
FALSE

F-EIS-RCS.1
6.03.02
The RCS shall consist of two parts 1. The main RCS Ring, and 2. The High energy transfer line terminating with the ESR injection system
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.2
6.03.03
The RCS shall be capable of accepting the bunches and matching the bunch parameters as injected by the BAR into the LTR transfer line.
05/16/2025
In Process
FALSE

F-EIS-RCS.3
6.03.02
After bunch injection into the RCS, the RCS shall merge the injected bunches into two bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.4
6.03.02
After bunch injection the RCS shall be able to accelerate the single bunch to the final desired energy set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS.5
6.03.02
The RCS needs to accelerate to the top possible energy in a time interval consistent with the parameters set forth in [5.9] at approximately 100 msecs for 18 GeV.
05/16/2025
In Process
FALSE

F-EIS-RCS.6
6.03.03
The RCS shall be capable of kicking the accelerated bunches into the RTE transfer line to the ESR.
05/16/2025
In Process
FALSE

F-EIS-RCS.7
6.03.02
RCS will need to increase the vertical emittance to match the ESR vertical emittance.
05/16/2025
In Process
FALSE

F-EIS-RCS.8
6.03.02
The RCS shall have a racetrack design with 160 arc FODO cells, bending radius of 91.67 m and two 86.624 m straight sections made up of 8 FODO cells with a total circumference of 1.421 km
05/16/2025
In Process
FALSE

F-EIS-RCS.15
6.03.02
The RCS lattice shall contain provisions for correctors such as dipole correctors etc., as needed.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-TLINE-GUN-Diagnostic.1
6.03.04
The Pre-injector separate diagnostic beamline section shall have 3 branches one with Faraday cup, one port containing a connection to the cathode Laser and a line to a low energy beam dump.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.1
6.03.04
The instrumentation in the diagnostic beamline to the low energy beam dump shall have the capability to measure beam position, profile, bunch charge
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.4
6.03.04
The Faraday cup shall be able to measure the charge of the electron bunches from the gun.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-LASER-INST.1
6.03.04
There shall be instrumentation capable of measuring the position and profile of the laser beam on the cathode.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-LASER.1
6.03.04
The laser beam shall illuminate the cathode perpendicular to the cathode face
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.1
6.03.04
The beam tube and flange sizes shall be appropriate to transport polarized e-beam between the e-source and the diagnostic beam line polarimeter chamber.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.2
6.03.04
Vacuum system shall be compatible with UHV requirements.
05/16/2025
Not Applicable
FALSE

F-EIS-TLINE-SPIN.INST.1
6.03.03
Profile monitor, BPM are placed at before, in between and after two Wien filters
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.1
6.03.03
Between the dipole chamber and the bunching section, two Wien filters shall be used as spin rotator to rotate the spin direction from longitudinal to vertical.
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.2
6.03.03
triplets focusing are used in between the two Wien filters to maintain the beam envolop
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.3
6.03.03
Quadpole single let and double let are used before and after Wien to compensate the quadropole components from the Wien entrance and exit
05/16/2025
In Process
FALSE

F-EIS-VAC.1
6.03.04
The EIS vacuum system shall meet UHV standards at a minimum (Ref vacuum spec?)
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.07
6.03.02.04
On 15 m on each side (or one vacuum section) of the SRF cavities the vacuum system shall be processed to class ISO 5.
05/16/2025
Approved
FALSE

F-EIS-VAC.3
6.03.04
The size, location and type of vacuum pumps shall be chosen to meet the required vacuum levels during operation
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-VAC.4
6.03.04
Appropriate vacuum gauging shall be supplied in each vacuum sector to monitor the required vacuum levels
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

G-EIS.9
6.03
The EIS shall provide an electron beam to the ESR having the bunch charge at extraction to meet the beam requirements as set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
Approved
FALSE

F-EIS- PREINJ-LINAC-MAG.1
6.03.04
A Quadrupole triplet shall be installed between each accelerating structure in the LINAC to control the beam beta function and dispersion.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.2
6.03.04
The LINAC Quadrupole triplets shall be optimized to control beams with high RCS injection energies ~ 400[MeV].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.3
6.03.04
In addition to the Quadrupole triplets X Y steering coils shall be installed between each 2.856[GHz] accelerator structure to control the beam beta function and dispersion in the LINAC.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.4
6.03.04
A LINAC XY steering coils shall be optimized to control beams which have low RCS injection energies < < 400[MeV]
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.1
6.03.04
The Pre-Injector S-band LINAC shall be able to accelerate all electron bunches up to the energy's required by [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.2
6.03.04
The Pre-Injector LINAC frequency shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.3
6.03.04
The Pre-Injector LINAC rep-rate shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.1
6.03.02
The instrumentation system shall contain a Beam Position Monitor system consisting of dual-plane Beam Position Monitors adjacent to each quadrupole.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.2
6.03.02
Select Beam Position Monitors in the injection region shall have turn-by-turn orbit measurement capability based on a single, remotely selectable bunch out of the fully filled bunch train to enable injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.3
6.03.02
The instrumentation system shall include a beam current monitor to measure average beam current.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.4
6.03.02
The instrumentation system shall include a system to measure individual bunch charges and bunch pattern.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.5
6.03.02
The instrumentation system shall include a system to measure transverse bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.6
6.03.02
The instrumentation system shall include a system to measure longitudinal bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.7
6.03.02
The instrumentation system shall contain a betatron and synchrotron tune monitors.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.8
6.03.02
The longitudinal bunch profile monitor needs turn-by-turn capability based on a single bunch in the fully filled bunch train to allow timing and energy adjustment for injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.9
6.03.02
The RCS shall contain a beam-based alignment system.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.10
6.03.02
The RCS shall contain a beam loss monitor system at select regions.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.3
6.03.02
The sextupoles shall be sorted into appropriate “families” and powered accordingly.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.4
6.03.02
There shall be dipole correctors capable of adjusting the beam orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.6
6.03.02
The quadrupoles shall generally be arranged in a conventional FODO structure.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.7
6.03.02
Each quadrupole strength needs to be capable of being changed independently by small amounts for beam-based alignment purposes.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.8
6.03.02
Sextupoles shall be sorted into “families” with the family structure dependent on the linear lattice configuration (betatron phase advance per FODO cell).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.9
6.03.02
The maximum integrated field strength of the FODO sextupoles needs to be sufficient to correct chromaticity to within 1 unit in both planes.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.10
6.03.02
Window-frame dipole corrector magnets capable of providing both horizontal and vertical dipole fields to correct the beam orbit in both transverse planes shall be placed adjacent to most of the quadrupoles.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.11
6.03.02
The strength of the window-frame dipole correctors needs to be chosen to correct for any source of orbit distortion and should have a margin for beam based diagnostic purpose.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-GUN-INST.4
6.03.04
To characterize and control the fresh bunches sent to the Mott polarimeter, the gun diagnostic beamline shall contain instrumentation to measure and control the profile, position, and charge of the beam.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-INST.5
6.03.04
The Diagnostic beamline section shall have one Beam Profile Monitor and Wien Filter and an electrostatic bender before the Mott polarimeter and Faraday Cup.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-GUN-INST.6
6.03.04
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

F-EIS-GUN-MAG.1
6.03.04
Following the DC gun, the electron bunch shall be deflected through a bending dipole into the Bunching section
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.2
6.03.04
2 solenoids shall be placed between the gun and the bending dipole into the bunching section capable of correcting the beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.3
6.03.04
Provision shall be made for an appropriate number of air cored steering coils between the Gun and bunching section to correct the electron beam position as required.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.4
6.03.04
A bending dipole shall follow the Gun and be able to bend the beam from the gun into the bunching section OR bend separate electron bunches into the separate diagnostic beam line.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.5
6.03.04
The bending dipole after the gun shall also have the capability to deflect the beam enough to allow a laser to illuminate the photocathode head on.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.6
6.03.04
A minimum of three solenoids shall be placed between the gun and the first bunching cavity to maintain the beam size for 5–10 nC bunches
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.7
6.03.04
Short air core trim coils shall be used to correct beam position for energies greater than 100 keV
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.8
6.03.04
The Diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-VAC.3
6.03.04
The Laser section shall be independent from the Gun\diagnostic section vacuum.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN.3x
6.03.03
The low energy transfer line shall have an additional branch between the Gun and the Bunching section which can transfer individual electron bunches into the diagnostic beamline section.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.4x
6.03.03
The low energy transfer line shall have a laser port between the Gun and the Bunching section which will allow an optical path for the laser to illuminate the cathode face of the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.6x
6.03.04
The gun shall have steering coils to direct the liberated electrons (These can be reused from the existing Gun system.)
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-HETL-ESR-INJ.1
6.03.03
The transferred beam shall meet all the requirements of the circulating beam, for all operational modes of the ESR as set forth in [5.9].
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-INST-BPM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed Beam Position Monitors at the quadrupoles and at the entry and exit of a number of the dipoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-IC.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain FCT and an Integrating Current Transformer before the ESR injection septum.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-PM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed YAG\OTR at the entry and exit of a number of the diploes and quadrupoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-POL.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a system to measure the beam polarization.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-BUMP.1
6.03.03
ESR injection shall have three fast bump magnets to direct the bunches from the HETL into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker of the ESR injector system shall operate in unison with a septum magnet which can direct the beam into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-SLINE-FKICK.1
6.03.03
The ESR injection system shall have a fast strip line kicker with a rise time of 2nsecs .
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.1
6.03.03
The High Energy Transfer Line shall match the beam parameters between the extraction point of the RCS and injection point of the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.2
6.03.03
The extraction into the required High Energy transfer line shall match the ESR bunch spacing and spin pattern.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.3
6.03.03
The High Energy Transfer Line shall be spin transparent.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.4
6.03.03
The ESR extraction system shall have another three bump magnets, its own septum magnet and use the strip line injection kicker to extract and replace the circulating bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BLM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be a bunch length monitor(BLM) at the exit of the 3rd harmonic buncher cavity to measure bunch compression during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam position monitor (BPM) at the entry to the 1st harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section a beam position monitor (BPM) at the entry and exit of the 2nd harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.3
6.03.04
To characterize the beam as it exits the buncher section, beam position monitor(BPM) at the exit of the 3rd harmonic buncher cavity to measure beam position during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-EM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be an emittance monitor(EM), at the exit of the 3rd harmonic buncher cavity to measure beam position, the beam emittance during commissioning.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-EM.01
6.03.04.02.06
Emittances shall be measured using a profile monitor and a dedicated upstream quadrupole configured to measure H, V, and skew profiles.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.03
6.03.04.02.06
The EM shall be able to measure the expected normalized emittance of 40 um
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.02
6.03.04.02.06
Before the 400 MeV beam goes into the spin rotator, the emittance shall be measured by a quad scan
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.04
6.03.04.02.06
Beam emittance shall be measured in the low energy diagnostics beamline using a slit scanner and profile monitor
05/16/2025
On Hold
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.1
6.03.04
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), at the entry and exit of the 2nd harmonic buncher cavity to measure charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.2
6.03.04
To characterize the beam as it exits the buncher section, an integrating current transformer(ICT) at the exit of the 3rd harmonic buncher cavity to measure the bunch charge during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-LM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam loss monitor (BLM) at the entry to the 1st harmonic buncher cavity to measure beam loss
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a transverse profile monitor(TPM) at the entry to the 1st harmonic buncher cavity to measure the charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section there shall be a transverse profile monitor(TPM) at the entry and exit of the 2nd harmonic buncher cavity to measure the bunch profille.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.3
6.03.04
To characterize the beam as it exits the buncher section, transverse profile monitor(TPM) at the exit of the 3rd harmonic buncher cavity the bunch profile during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-MAG-SOL.4
6.03.04
The solenoidal field shall extend to also contain the 1st RF tank of the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-CAV.1
6.08
The LINAC TWP cavities shall be constant gradient cavities
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-INST-CM.1
6.03.04
Bunch charge measurements shall be performed at multiple locations through the LINAC.
05/16/2025
In Process
FALSE

F-EIS-LINAC-INST-PM.1
6.03.04
To measure the beam profile in the LINAC section there shall be a plunging YAG/OTR transverse profile monitor between the 1st and 2nd accelerating cells.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.3
6.03.04
Between each S-band LINAC section there shall be at least two window frame steering magnets.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.4
6.03.04
Additionally, window frame steering magnets will be placed at the entry and exit of each accelerating structure to position the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.2
6.03.04
At the end of the Zigzag there shall be a diagnostic section (details TBD) to measure the bunch length and dP/P.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.2
6.03.04
The longitudinal matching section shall consist of a so-called Zigzag section followed by a de-chirp cavity which will stretch the bunch length to 40 ps, reduce the energy spread, and generate a longitudinal phase space rotation of the bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.2
6.03.03
The fast kicker magnet shall follow the rise and fall of the amplitude of the RF sinusoidal functions
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST-BPM.1
6.03.03
To control the beam through the Spin Rotator section there shall be a Beam Position Monitors placed throughout the spin rotator as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST.1
6.03.03
To measure and control the beam in the medium energy 400 MeV transfer line there shall be sufficient beam position monitors for orbit control, transverse profile monitors, and bunch charge monitors as required.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

F-EIS-METL-MAG-DIP.1
6.03.03
At the entry to the spin rotator section before the spin rotator solenoid there shall be a number of bending dipole to rotate the polarization spin from the Longitudinal direction into the transverse X direction.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-DIP.2
6.03.03
After the exit of spin rotator solenoid, there shall be a number of bending dipoles to close the geometry and direct the beam into the medium energy 400[MeV] transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.5
6.03.03
The spin rotator quadrupoles after the Spin rotator solenoid shall be able to match the beam beta functions βx and βy to that required for entry into the 400MeV transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.6
6.03.03
The spin rotator exit quadrupoles shall have at least 2 families this is required to control the electron beam optics as needed.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.7
6.03.03
The spin rotator solenoid shall rotate the electron beam spin from the X axis to the vertical y-axis before it enters the medium [400MeV] transport line to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.8
6.03.03
The spin rotator solenoid shall have an integrated gradient of 2.2 [T.m] required to rotate the spin from the horizontal axis to the vertical axis.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.1
6.03.03
The bump magnets shall have a rise and time consistent with the requirements of the circulating bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.2
6.03.03
The Pulsed bump magnets shall be able to create a closed orbit path passing close to the Septum and maintain it during each injection cycle (100-150 Hz).
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.6
6.03.03
Each train of four bunches shall be injected into neighboring RF buckets to facilitate bunch merges.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.7
6.03.03
The injection system shall be capable of maintaining the small spacing required by the injected bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.11
6.03.03
The injection system into the RCS shall be capable of injecting successive bunches into the RCS to create a bunch train with four bunches each circulating in the RCS ready to be merged.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.12
6.03.03
The RCS shall be capable of merging each train of 4 bunches into a larger single bunch to create larger single circulating bunche in the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.2
6.03.03
The Medium energy transfer line shall contain 3 sections: 1. Spin rotation section, 2. The main transfer line, 3. The Injector system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.3
6.03.03
There will be number of corrector Quadrupoles after the Pre-Injector longitudinal matching and before the spin rotator to provide beam matching into the Spin Rotator.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.4
6.03.03
The medium energy 400 MeV transfer line shall be able to transport the spin reoriented beam from the spin rotator to the RCS injection system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.5
6.03.03
The medium energy 400 MeV transfer line will maintain the spin direction of the beam along the entire transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.6
6.03.03
The spin rotator shall ensure the spin direction of the electron bunches are rotated from the longitudinal Z axis to the vertical Y axis.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH-INST.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be beam position monitor (BPM), and a transverse profile monitor at the entry to the buncher cavity to measure beam loss, position, and charge.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.2
6.06.03
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), beam position monitors and transverse profile monitors
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.3
6.06.03
To characterize the beam as it exits the buncher section, there shall be an emittance measurement including slit and beam viewer, an integrating current transformer, beam position monitor, charge and compression during commissioning.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-RF.1
6.08
one 197 MHz buncher cavity shall be used for providing bunch chirp
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.2
6.08
The bunching section shall generate sufficient compression to compress the bunch length to that required by [5.9].
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.3
6.08
The bunchers rf voltage and phase will be synchronized so that the passing electron bunches meet the required beam characteristics at the end of the buncher section.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.4
6.08
The Pre-Injector layout shall accommodate all RF cavities and allow enough room for other Pre-Injector components.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-LINAC-VAC.1
6.03.04
The LINAC section shall contain enough strategically located Vacuum gate valves, to allow access to the vacuum volume as needed.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.1
6.03.03
The LTR transfer line shall terminate with an injection system capable of transferring the beam into the RCS for all the operating energies and conditions specified in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.3
6.03.03
The vertically spin polarized electron bunch patterns generated by the pre-injector shall be transferred into the RCS unaltered.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.1
6.08
There shall be a special RF kicker to kick the injected beam into neighboring RF buckets without disturbing the 8 circulating bunches.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ.1
6.03.04
The EIS Pre-Injector shall consist of 3 sub-systems: 1. An electron gun section, followed by 2. A low energy transfer line and bunching section, followed by 3. A LINAC section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-INST.1
6.03.04
EIS shall have all the beam instrumentation necessary to deliver the operational parameters set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-HETL-INST-BPM-ELEC.01
6.03.03.04.01
The BPM single bunch measurement resolution for a (1 - 4 nC) pilot bunch shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.02
6.03.03.04.01
The BPM single bunch measurement resolution for (5.5 - 28 nC) bunches shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.03
6.03.03.04.01
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.04
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used to measure the transport lattice.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.01
6.03.03.04.01
The BPM Pickup alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.02
6.03.03.04.01
The BPM Pickup shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.04
6.03.03.04.01
The BPM Pickups shall be located by the dipole correctors at every second quadrupole.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM-ELEC.01
6.03.03.04.01
For a (1 nC) pilot bunch, the BPM single bunch measurement resolution shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.02
6.03.03.04.01
For (5.5 - 10 nC) bunches, the BPM single bunch measurement resolution shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.03
6.03.03.04.01
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.04
6.03.03.04.01
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.01
6.03.03.04.01
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.02
6.03.03.04.01
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.04
6.03.03.04.01
The location of the BPM Pickups shall be TBD
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.01
6.03.02.05.04
A synchrotron light monitor (SLM) shall be installed in the RCS ring downstream of an RCS dipole magnet
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.02
6.03.02.05.04
The location of the SLM light extraction port shall be- TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.03
6.03.02.05.04
The synchrotron light shall be transported from the RCS light extraction port to an optical table for detection.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.04
6.03.02.05.04
The synchrotron light optical table shall have a streak camera and gated camera shall be installed.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.05
6.03.02.05.04
The SLM shall be able to make Turn-by-turn measurements using gated cameras to provide measurements of; the injection matching parameters and the beam position stability parameters during acceleration. TBD -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.06
6.03.02.05.04
The SLM shall be used to provide horizontal and vertical transverse profile measurements on bunches with charges > 6nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.07
6.03.02.05.04
The SLM horizontal and vertical transverse profile measurements shall be measured with a resolution in both planes of 0.1 mm
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.08
6.03.02.05.04
The SLM shall be used to provide longitudinal profile measurements
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.09
6.03.02.05.04
A dual sweep streak camera shall be used to provide measurements of the bunch length and longitudinal profiles
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.10
6.03.02.05.04
The dual sweep streak camera shall have a resolution of <5 ps
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.11
6.03.02.05.04
The profile measurements shall be used, together with modeled or measured beam optics to infer the beam emittances and energy spread.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.12
6.03.02.05.04
The Vertical emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.6 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.13
6.03.02.05.04
The Horizontal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 10 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.14
6.03.02.05.04
The Longitudinal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.00001 eV-s
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.15
6.03.02.05.04
The Energy spread measurement, for bunch charges > 6nC, shall be measured with a precision of 0.0001 dp/p
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.01
6.04.06.02
A bunch pattern monitor shall be installed in the ESR to measure indiviual bunch charge with an accuracy 1 %
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.02
6.04.06.02
The Bunch pattern monitor shall be capable of measuring Bunch patterns ranging from a single bunch, to a filled ring with 1,160 bunches
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.01
6.04.06.05
BLM shall be needed to needed to protect sensitive equipment.
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.02
6.04.06.05
The number of BLM installed in the ESR shall be TBD ea
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.03
6.04.06.05
BLM shall be installed at the following locations in the ESR TBD
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.04
6.04.06.05
The sensitivity of the BLM detectors shall be TBD units?
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.05
6.04.06.05
Where possible existing RHIC BLM's can be relocated to identify ESR & HSR losses
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.06
6.04.06.05
The response time from loss detection to abort shall be TBD us
05/16/2025
In Process
FALSE

P-ESR-INST-BPM-ELEC.01
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following capabilities defined for the low intensity pilot injection energies and high intensity collision energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following time resolutions for data refresh defined for the beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.03
6.04.06.01
The ESR BPM Electronics shall have the following time resolutions for data logging defined for the beam energies:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.04
6.04.06.01
The ESR BPM Electronics shall have the following measurement resolutions defined for beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.05
6.04.06.01
The ESR BPM Electronics shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.06
6.04.06.01
The ESR BPM Electronics shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-PU.01
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall provide dual plane (horizontal and vertical) beam positional measurements.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) shall be positioned in the following locations approved by physics as defined in the lattice:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.03
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) mechanical and electrical center in the locations identified shall be:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.04
6.04.06.01
The ESR Beam Position Monitor Pick-Ups housing shall have a +/- 10 (mrad) corresponding to +/- 0.6 (degree) roll tolerance with regards to BPM measurements in respect to the vacuum chamber.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.05
6.04.06.01
The ESR Beam Position Monitor Pick-Ups design shall be less than or equal to the allocated impedance and is within the accepted overall ESR impedance budget approved by physics. (replace with loss factor)
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.06
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall fulfill resolution requirements over the horizontal and vertical beam position range with respect to its fiducials of +/- 3 (mm).
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.07
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to ensure the maximum temperatures of the components (due to heating by the beam) are acceptable for reliability and operations of the EIC over the planned operational life of 20 (yrs).
09/15/2025
In Process
FALSE

P-ESR-INST-BPM-PU.09
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to be baked to 250 °C for UHV processing.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.10
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.11
6.04.06.01
The ESR BPM Pickup shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/30/2025
In Process
FALSE

P-ESR-INST-BPM-PU.12
6.04.06.01
The ESR Beam Position Monitor Button configuration will be mirror symmetric with respect to the mid-and center planes. Deviation from symmetry shall be such that corresponding BPM reading errors are less then 20 microns.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.13
6.04.06.01
The ESR Beam Position Monitor Pick-Ups symmetrical configuration (postion between the four buttons and the relative to the fiducials on top of the button) shall be stable under the inference of the expected operational thermal changes to the extent that corresponding changes in the bpm reading deviate less than 20 µm.
07/25/2025
Approved
FALSE

P-ESR-INST-DCCT.01
6.04.06.02
A DCCT shall measure the average beam current in the ESR.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.02
6.04.06.02
The measurement resolution averaged over 1 sec shall be < 5 uA
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.03
6.04.06.02
The DCCT beamline device impedance shall be approved by beam physics.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.04
6.04.06.02
Measurement drift tolerance (thermal effects) shall be ≤ 1 uA/K
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.05
6.04.06.02
The DCCT sensor in the ring shall operate in the temperature range of 15 to 35 degrees C
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.06
6.04.06.02
The range of average beam current to be measured shall be 0.156x10-3 to 2.5 A
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.07
6.04.06.02
The DCCT system shall have a remote controlled self calibration system
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.08
6.04.06.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.09
6.04.06.02
The measured average current shall be provided to users at a rate of 10 Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.10
6.04.06.02
The measured average current shall be archived at a rate of 10 Hz Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.11
6.04.06.02
The DCCT sensor assembly in the ring shall be radiation resistant
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.01
6.04.06.03
The requirements for longitudinal feedback are ??? TBD
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.02
6.04.06.03
The Longitudinal feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.01
6.04.06.04
The ESR shall have two synchrotron light monitors (SLM) and one X-ray pin hole monitor
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.02
6.04.06.04
The longitudinal bunch profile monitor shall have a turn-by-turn capability based on a single bunch in the fully filled bunch train.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.03
6.04.06.04
TThe SLM systems shall measure the crabbing angle, longitudinal bunch parameters, H & V beam size and global coupling.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.04
6.04.06.04
The SLM shall be able to measure a crabbing angle of 12.5 mrad with accuracy of 10 %
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.05
6.04.06.04
The SLM shall be able to measure the Longitudinal bunch parameters with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.06
6.04.06.04
The SLM shall be able to measure the H & V beam size with accuracy of H=?? V=?? units
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.07
6.04.06.04
The SLM shall be able to measure the Global coupling with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.08
6.04.06.04
One SLM port shall be located downstream of a dipole in an appropriate location in the ESR, exact location not critical.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.09
6.04.06.04
The second SLM port shall be located in a complimentary location in the lattice to ensure all the necessary SLM measurements can be made. TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.10
6.04.06.04
The SLM light extraction port mirrors shall be good quality, having a surface finish better than 1/10 Lambda
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.11
6.04.06.04
The SLM light extraction port mirrors shall be water cooled to avoid image distortion.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.12
6.04.06.04
There shall be an enclosed SL transport from the light extraction port to the SLM optical lab rooms. Length to be determined by the distance to optical lab room, should be minimized to reduce vibration problems.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.13
6.04.06.04
The locations of the SLM optical lab rooms shall be TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.14
6.04.06.04
The double-slit interferometer method shall be used to measure transverse beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.15
6.04.06.04
The standard transverse resolution of an SLM using visible light shall be ~60 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.16
6.04.06.04
The resolution using the double-slit method shall equal to 10 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.17
6.04.06.04
A streak camera shall be used to measure the bunch longitudinal profiles
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.18
6.04.06.04
A position sensitive photo-diode will provide photon beam centroid information which shall supplement the orbit stability measurements by the BPMs
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.19
6.04.06.04
A GigE CCD/CMOS camera, externally triggerable with exposure times ranging from 10 nsec to 5 sec, shall be used to image the visible radiation
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.20
6.04.06.04
A commercially available gated camera with gate width of <2 nsec (compared to a minimum bunch spacing of 10 nsec) shall be used to detect injection oscillations and for beam studies.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.21
6.04.06.04
The location of the X-ray pinhole monitoring system shall be TBD
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.22
6.04.06.04
The target resolution of the X-ray pin hole monitoring system shall be ~ 5 um (or as best that can be achieved with the machine parameters and commercial equipment) 5 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.23
6.04.06.04
The X-ray pin hole monitor shall provide independent measurement of the energy spread and horizontal/vertical emittance. H=V=15.4 nm
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.24
6.04.06.04
The X-ray pinhole photon beamline shall be equipped with gated cameras that will be employed to provide high resolution turn-by-turn profile measurements
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.25
6.04.06.04
A pinhole assembly including tungsten slits shall provide sufficient resolution to precisely measure the beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.26
6.04.06.04
Several different size pinholes sizes shall be incorporated to allow easy alignment and measurements at different beam currents and energies.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.01
6.04.06.03
Stripline kickers (H & V) shall be used to excite the beam so tunes can be measured using turn-by-turn BPM data.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.02
6.04.06.03
The magnitude of the kick required for the horizontal kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.03
6.04.06.03
The magnitude of the kick required for the vertical kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.04
6.04.06.03
The kicker waveform (risetime and shape) requirements shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.05
6.04.06.03
The location of the tune meter kicker striplines in the ESR shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.06
6.04.06.03
The impedance of the kicker beamline device shall be approved by beam Physics.
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.01
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.03
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.02
6.04.06.03
The transverse feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSSLFB.01
6.04.06.03
The transverse slow feedback system bandwidth shall bs 10 Hz
05/16/2025
In Process
FALSE

F-EIS-LINAC-MAG-QUAD.3
6.03.04
A drift space with quadrupole triplets shall be placed between each TWP structure to tune the bunch beta function through the LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.1
6.03.04
Following the Zigzag there shall be a de-chirp cavity to linearize and reduce the energy spread of the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-DIP.1
6.03.04
The ZigZag section shall consist of a number of dipoles separated by drift spaces in a R56 configuration to increase the bunch length to 40ps.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-QUAD.1
6.03.04
The ZigZag section shall consist of a number of Quadrapoles to control the beam dispersion through the zigzag.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.1
6.03.04
A longitudinal matching section shall follow the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.3
6.03.04
At the Zigzag exit, the electron beam’s average spin orientation shall be longitudinal in the direction of beam travel.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.1
6.03.03
The fast kicker magnet shall be capable of deflecting the electron beam from the RCS to counter the RF kick.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.4
6.03.03
The spin rotator entry quadrupole shall have at least 2 families this is needed to control the electron beam optics as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.1
6.03.03
The Medium energy transfer line shall transfer the beam from the pre-injector longitudinal matching section to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH.1
6.03.03
The pre-injector LEBT low energy RF section shall transfer the electron beam from the gun to the linac section. shall provide bunching and initial acceleration to each 1 nC bunch
05/16/2025
In Process
FALSE

F-EIS-PREINJ-GUN.2
6.03.04
The pre-injector electron gun shall produce all the bunch patterns required to deliver the ESR beam requirements set forth in [5.9].
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.21
6.03.04
The diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.1
6.03.03
The pre-injector shall have a low energy transfer line from the gun into the beam compression "Bunching" section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.6
6.03.04
Following the gun, there shall be multiple groups of magnets required to control the electron beam.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.7
6.03.04
To characterize and control the fresh bunches the low energy transfer line from the Gun to the Buncher shall contain a plunging transverse profile monitor, a bunch charge monitor, beam loss monitors, and beam position monitors
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-TLINE-MEBT-MAG-QUAD.1
6.03.03
The corrector Quadrupoles shall be able to suppress the βx and βy along the transfer line to levels consistent with those required ate the RCS injection kicker.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-SEP.1
6.03.03
The septum magnet shall be capable of deflecting the incoming electron beam into the RCS and shielding the circulating beam already in the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.2
6.03.03
The injection system shall inject the beam at Need update
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.4
6.03.03
The injection system shall be able to inject one bunch per injection kick using RF and magnetic kickers to build up a total of 8 bunches from 4 kicks to the RF and kickers.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.5
6.03.03
The injection system shall ensure the bunch emittance shall match the requirements of the RCS RF system and such, to avoid collective instabilities and to stay within the off-momentum aperture.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.9
6.03.03
The injection system shall contain 3 bump magnets to locally bump the RCS circulating beam close to the injection septum.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.10
6.03.03
The RCS injection system shall contain an RF kicker and a pulsed magnet followed by a septum magnet to redirect the beam into the RCS closed orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.11
6.03.03
The magnetic field of the injection system pulsed magnet shall follow the rise time of the power amplifiers which drive the RF kickers..
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.2
6.08
The special kicker shall consist of an RF harmonic kicker with fundamental frequency of 1/4 of the main RCS RF cavity or compatible equivalent alternative.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.3
6.08
The special kicker shall have a rise and fall time that matches the RF bucket size.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.4
6.08
The special kicker shall have a peak power necessary to generate a kick to inject the bunch into the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.5
6.08
The special kicker shall have a macro pulse with a flattop that is greater than the time between the LINAC bunches and shall have a rise and fall time less than 1 RCS turn.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.6
6.08
The special kicker shall be able to repeat at the LINAC pulse rate.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT.28
6.03.03
The LTR transfer line shall have several FODO quadrupoles to control the beta function along the transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ.3
6.03.04
The EIS Pre-Injector shall create bunches which meet the requirements set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PROT-COLL.1
6.06.03
The RCS shall have a collimation system to protect all other apertures in the RCS.
05/16/2025
In Process
FALSE

F-EIS-RCS-MAG-QUAD.5
6.03.02
The quadrupoles shall be individually powered with low supplementary current/voltage power supplies for beam-based alignment purposes.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.7
6.03.02
The RCS straight sections shall have the appropirate number of defocusing and focusing quadrupole families per straight section.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.9
6.03.02
The non-colliding straights will have different scheme.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.14
6.03.02
The main arc quadrupoles shall be powered by a total of 2 power circuits 1 for focusing the other defocusing.
05/16/2025
In Process
FALSE

F-EIS-RCS-MAG.15
6.03.02
The quadrupoles in both straight sections shall need a total of 6 power circuits to power all six families of quadrupoles in both straights. (straights are optically identical)
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.18
6.03.02
The RCS magnets shall be fed by a system of power supplies matched in voltage and maximum current to the specifications and requirements of the respective magnets.
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-BUMP.1
6.03.03
the RCS extraction system shall have three fast bump magnets to direct the bunches to the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-FKICK.1
6.03.03
RCS extraction shall be facilitated with a fast kicker having a rise time of 2 micro-secs
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker shall operate in unison with a septum magnet which can direct the beam into the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.1
6.03.03
The beam injection of the electron bunches from the RCS into the ESR ring shall take place in the 12 o’clock straight section.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.2
6.03.03
There will be two electron bunches circulating in the RCS at extraction, these shall be injected into the High Energy Transfer Line which connects the RCS to the ESR.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.1
6.08
The RF system shall Provide a maximum RF voltage of 60MV to accelerate the beam.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.2
6.08
The total RF power provided by the RF amplifiers shall be able to compensate for all additional losses created by the stored electron beam in addition to the acceleration and synchrotron losses.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.3
6.08
The RF system shall Provide sufficient gradient to allow installation of all necessary RF modules in the limited space in IR 10.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.4
6.08
The RF system shall be able to accommodate 4 circulating bunches in one trains of 4 bunches.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.5
6.08
The RF system shall be able to merge the one train of 4 bunches into two larger separate circulating bunches then merge these two large bunches into a single larger circulating bunch.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.6
6.08
The RF system shall be able to accelerate final large, merged bunch to the operating energies needed by the ESR as set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.7
6.03.02
The RF system controls shall be designed to handle the transient beam loading for all bunch structures.
05/16/2025
In Process
FALSE

F-EIS-RCS-VAC.1
6.03.02
The vacuum chamber shall provide sufficient horizontal and vertical aperture to accommodate a beam which is 5 σ larger than the largest sigma beam size determined by the injected RMS emittance.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.2
6.03.02
The average dynamic pressure around the ring shall be < 5e-8[Torr] after 1 year of operation.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.3
6.03.02
The impedance of the entire RCS vacuum system shall allow for the bunch intensities, beam currents, and bunch numbers contained in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.09
6.03.02.04
The vacuum chamber shall be capable of absorbing and carrying away the eddy current power.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.4
6.03.02
The vacuum chamber and all its components shall be designed to withstand the total synchrotron radiation loads seen in operation.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-VAC.08
6.03.02.04
The vacuum chamber shall be capable of absorb synchrotron radiation and carrying away the absorbed power.
05/16/2025
Approved
FALSE

F-EIS-RCS.1
6.03.02
The RCS shall consist of two parts 1. The main RCS Ring, and 2. The High energy transfer line terminating with the ESR injection system
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.2
6.03.03
The RCS shall be capable of accepting the bunches and matching the bunch parameters as injected by the BAR into the LTR transfer line.
05/16/2025
In Process
FALSE

F-EIS-RCS.3
6.03.02
After bunch injection into the RCS, the RCS shall merge the injected bunches into two bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.4
6.03.02
After bunch injection the RCS shall be able to accelerate the single bunch to the final desired energy set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS.5
6.03.02
The RCS needs to accelerate to the top possible energy in a time interval consistent with the parameters set forth in [5.9] at approximately 100 msecs for 18 GeV.
05/16/2025
In Process
FALSE

F-EIS-RCS.6
6.03.03
The RCS shall be capable of kicking the accelerated bunches into the RTE transfer line to the ESR.
05/16/2025
In Process
FALSE

F-EIS-RCS.7
6.03.02
RCS will need to increase the vertical emittance to match the ESR vertical emittance.
05/16/2025
In Process
FALSE

F-EIS-RCS.8
6.03.02
The RCS shall have a racetrack design with 160 arc FODO cells, bending radius of 91.67 m and two 86.624 m straight sections made up of 8 FODO cells with a total circumference of 1.421 km
05/16/2025
In Process
FALSE

F-EIS-RCS.15
6.03.02
The RCS lattice shall contain provisions for correctors such as dipole correctors etc., as needed.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-TLINE-GUN-Diagnostic.1
6.03.04
The Pre-injector separate diagnostic beamline section shall have 3 branches one with Faraday cup, one port containing a connection to the cathode Laser and a line to a low energy beam dump.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.1
6.03.04
The instrumentation in the diagnostic beamline to the low energy beam dump shall have the capability to measure beam position, profile, bunch charge
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.4
6.03.04
The Faraday cup shall be able to measure the charge of the electron bunches from the gun.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-LASER-INST.1
6.03.04
There shall be instrumentation capable of measuring the position and profile of the laser beam on the cathode.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-LASER.1
6.03.04
The laser beam shall illuminate the cathode perpendicular to the cathode face
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.1
6.03.04
The beam tube and flange sizes shall be appropriate to transport polarized e-beam between the e-source and the diagnostic beam line polarimeter chamber.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.2
6.03.04
Vacuum system shall be compatible with UHV requirements.
05/16/2025
Not Applicable
FALSE

F-EIS-TLINE-SPIN.INST.1
6.03.03
Profile monitor, BPM are placed at before, in between and after two Wien filters
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.1
6.03.03
Between the dipole chamber and the bunching section, two Wien filters shall be used as spin rotator to rotate the spin direction from longitudinal to vertical.
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.2
6.03.03
triplets focusing are used in between the two Wien filters to maintain the beam envolop
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.3
6.03.03
Quadpole single let and double let are used before and after Wien to compensate the quadropole components from the Wien entrance and exit
05/16/2025
In Process
FALSE

F-EIS-VAC.1
6.03.04
The EIS vacuum system shall meet UHV standards at a minimum (Ref vacuum spec?)
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.07
6.03.02.04
On 15 m on each side (or one vacuum section) of the SRF cavities the vacuum system shall be processed to class ISO 5.
05/16/2025
Approved
FALSE

F-EIS-VAC.3
6.03.04
The size, location and type of vacuum pumps shall be chosen to meet the required vacuum levels during operation
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-VAC.4
6.03.04
Appropriate vacuum gauging shall be supplied in each vacuum sector to monitor the required vacuum levels
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

G-EIS.10
6.03
The EIS bunch replacement process shall deliver polarized replacement bunches capable of creating all the ESR polarization patterns needed to meet the physics goals.
05/16/2025
Approved
FALSE

F-EIS- PREINJ-LINAC-MAG.1
6.03.04
A Quadrupole triplet shall be installed between each accelerating structure in the LINAC to control the beam beta function and dispersion.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.2
6.03.04
The LINAC Quadrupole triplets shall be optimized to control beams with high RCS injection energies ~ 400[MeV].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.3
6.03.04
In addition to the Quadrupole triplets X Y steering coils shall be installed between each 2.856[GHz] accelerator structure to control the beam beta function and dispersion in the LINAC.
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC-MAG.4
6.03.04
A LINAC XY steering coils shall be optimized to control beams which have low RCS injection energies < < 400[MeV]
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.1
6.03.04
The Pre-Injector S-band LINAC shall be able to accelerate all electron bunches up to the energy's required by [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.2
6.03.04
The Pre-Injector LINAC frequency shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- PREINJ-LINAC.3
6.03.04
The Pre-Injector LINAC rep-rate shall be consistent with the needs defined in [5.9].
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.1
6.03.02
The instrumentation system shall contain a Beam Position Monitor system consisting of dual-plane Beam Position Monitors adjacent to each quadrupole.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.2
6.03.02
Select Beam Position Monitors in the injection region shall have turn-by-turn orbit measurement capability based on a single, remotely selectable bunch out of the fully filled bunch train to enable injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.3
6.03.02
The instrumentation system shall include a beam current monitor to measure average beam current.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.4
6.03.02
The instrumentation system shall include a system to measure individual bunch charges and bunch pattern.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.5
6.03.02
The instrumentation system shall include a system to measure transverse bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.6
6.03.02
The instrumentation system shall include a system to measure longitudinal bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.7
6.03.02
The instrumentation system shall contain a betatron and synchrotron tune monitors.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.8
6.03.02
The longitudinal bunch profile monitor needs turn-by-turn capability based on a single bunch in the fully filled bunch train to allow timing and energy adjustment for injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.9
6.03.02
The RCS shall contain a beam-based alignment system.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.10
6.03.02
The RCS shall contain a beam loss monitor system at select regions.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.3
6.03.02
The sextupoles shall be sorted into appropriate “families” and powered accordingly.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.4
6.03.02
There shall be dipole correctors capable of adjusting the beam orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.6
6.03.02
The quadrupoles shall generally be arranged in a conventional FODO structure.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.7
6.03.02
Each quadrupole strength needs to be capable of being changed independently by small amounts for beam-based alignment purposes.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.8
6.03.02
Sextupoles shall be sorted into “families” with the family structure dependent on the linear lattice configuration (betatron phase advance per FODO cell).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.9
6.03.02
The maximum integrated field strength of the FODO sextupoles needs to be sufficient to correct chromaticity to within 1 unit in both planes.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.10
6.03.02
Window-frame dipole corrector magnets capable of providing both horizontal and vertical dipole fields to correct the beam orbit in both transverse planes shall be placed adjacent to most of the quadrupoles.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.11
6.03.02
The strength of the window-frame dipole correctors needs to be chosen to correct for any source of orbit distortion and should have a margin for beam based diagnostic purpose.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-GUN-INST.4
6.03.04
To characterize and control the fresh bunches sent to the Mott polarimeter, the gun diagnostic beamline shall contain instrumentation to measure and control the profile, position, and charge of the beam.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-INST.5
6.03.04
The Diagnostic beamline section shall have one Beam Profile Monitor and Wien Filter and an electrostatic bender before the Mott polarimeter and Faraday Cup.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-GUN-INST.6
6.03.04
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

F-EIS-GUN-MAG.2
6.03.04
2 solenoids shall be placed between the gun and the bending dipole into the bunching section capable of correcting the beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.3
6.03.04
Provision shall be made for an appropriate number of air cored steering coils between the Gun and bunching section to correct the electron beam position as required.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.4
6.03.04
A bending dipole shall follow the Gun and be able to bend the beam from the gun into the bunching section OR bend separate electron bunches into the separate diagnostic beam line.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.5
6.03.04
The bending dipole after the gun shall also have the capability to deflect the beam enough to allow a laser to illuminate the photocathode head on.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.6
6.03.04
A minimum of three solenoids shall be placed between the gun and the first bunching cavity to maintain the beam size for 5–10 nC bunches
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.7
6.03.04
Short air core trim coils shall be used to correct beam position for energies greater than 100 keV
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.8
6.03.04
The Diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-VAC.3
6.03.04
The Laser section shall be independent from the Gun\diagnostic section vacuum.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN.3x
6.03.03
The low energy transfer line shall have an additional branch between the Gun and the Bunching section which can transfer individual electron bunches into the diagnostic beamline section.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.4x
6.03.03
The low energy transfer line shall have a laser port between the Gun and the Bunching section which will allow an optical path for the laser to illuminate the cathode face of the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.6x
6.03.04
The gun shall have steering coils to direct the liberated electrons (These can be reused from the existing Gun system.)
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-HETL-ESR-INJ.1
6.03.03
The transferred beam shall meet all the requirements of the circulating beam, for all operational modes of the ESR as set forth in [5.9].
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-INST-BPM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed Beam Position Monitors at the quadrupoles and at the entry and exit of a number of the dipoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-IC.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain FCT and an Integrating Current Transformer before the ESR injection septum.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-PM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed YAG\OTR at the entry and exit of a number of the diploes and quadrupoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

F-EIS-HETL-INST-POL.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a system to measure the beam polarization.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-BUMP.1
6.03.03
ESR injection shall have three fast bump magnets to direct the bunches from the HETL into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-MAG-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker of the ESR injector system shall operate in unison with a septum magnet which can direct the beam into the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-SLINE-FKICK.1
6.03.03
The ESR injection system shall have a fast strip line kicker with a rise time of 2nsecs .
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.1
6.03.03
The High Energy Transfer Line shall match the beam parameters between the extraction point of the RCS and injection point of the ESR.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.2
6.03.03
The extraction into the required High Energy transfer line shall match the ESR bunch spacing and spin pattern.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.3
6.03.03
The High Energy Transfer Line shall be spin transparent.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL.4
6.03.03
The ESR extraction system shall have another three bump magnets, its own septum magnet and use the strip line injection kicker to extract and replace the circulating bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BLM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be a bunch length monitor(BLM) at the exit of the 3rd harmonic buncher cavity to measure bunch compression during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam position monitor (BPM) at the entry to the 1st harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section a beam position monitor (BPM) at the entry and exit of the 2nd harmonic buncher cavity to measure beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-BPM.3
6.03.04
To characterize the beam as it exits the buncher section, beam position monitor(BPM) at the exit of the 3rd harmonic buncher cavity to measure beam position during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-EM.1
6.03.04
To characterize the beam as it exits the buncher section, there shall be an emittance monitor(EM), at the exit of the 3rd harmonic buncher cavity to measure beam position, the beam emittance during commissioning.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-EM.01
6.03.04.02.06
Emittances shall be measured using a profile monitor and a dedicated upstream quadrupole configured to measure H, V, and skew profiles.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.03
6.03.04.02.06
The EM shall be able to measure the expected normalized emittance of 40 um
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.02
6.03.04.02.06
Before the 400 MeV beam goes into the spin rotator, the emittance shall be measured by a quad scan
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-EM.04
6.03.04.02.06
Beam emittance shall be measured in the low energy diagnostics beamline using a slit scanner and profile monitor
05/16/2025
On Hold
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.1
6.03.04
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), at the entry and exit of the 2nd harmonic buncher cavity to measure charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-ICT.2
6.03.04
To characterize the beam as it exits the buncher section, an integrating current transformer(ICT) at the exit of the 3rd harmonic buncher cavity to measure the bunch charge during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-LM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a beam loss monitor (BLM) at the entry to the 1st harmonic buncher cavity to measure beam loss
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be a transverse profile monitor(TPM) at the entry to the 1st harmonic buncher cavity to measure the charge.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.2
6.03.04
To control the beam and to measure bunch compression through the buncher section there shall be a transverse profile monitor(TPM) at the entry and exit of the 2nd harmonic buncher cavity to measure the bunch profille.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-INST-TPM.3
6.03.04
To characterize the beam as it exits the buncher section, transverse profile monitor(TPM) at the exit of the 3rd harmonic buncher cavity the bunch profile during commissioning.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-BNCHR-MAG-SOL.4
6.03.04
The solenoidal field shall extend to also contain the 1st RF tank of the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-CAV.1
6.08
The LINAC TWP cavities shall be constant gradient cavities
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-INST-CM.1
6.03.04
Bunch charge measurements shall be performed at multiple locations through the LINAC.
05/16/2025
In Process
FALSE

F-EIS-LINAC-INST-PM.1
6.03.04
To measure the beam profile in the LINAC section there shall be a plunging YAG/OTR transverse profile monitor between the 1st and 2nd accelerating cells.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.3
6.03.04
Between each S-band LINAC section there shall be at least two window frame steering magnets.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-MAG-WF.4
6.03.04
Additionally, window frame steering magnets will be placed at the entry and exit of each accelerating structure to position the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.2
6.03.04
At the end of the Zigzag there shall be a diagnostic section (details TBD) to measure the bunch length and dP/P.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.2
6.03.04
The longitudinal matching section shall consist of a so-called Zigzag section followed by a de-chirp cavity which will stretch the bunch length to 40 ps, reduce the energy spread, and generate a longitudinal phase space rotation of the bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.2
6.03.03
The fast kicker magnet shall follow the rise and fall of the amplitude of the RF sinusoidal functions
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST-BPM.1
6.03.03
To control the beam through the Spin Rotator section there shall be a Beam Position Monitors placed throughout the spin rotator as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INST.1
6.03.03
To measure and control the beam in the medium energy 400 MeV transfer line there shall be sufficient beam position monitors for orbit control, transverse profile monitors, and bunch charge monitors as required.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

F-EIS-METL-MAG-DIP.1
6.03.03
At the entry to the spin rotator section before the spin rotator solenoid there shall be a number of bending dipole to rotate the polarization spin from the Longitudinal direction into the transverse X direction.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-DIP.2
6.03.03
After the exit of spin rotator solenoid, there shall be a number of bending dipoles to close the geometry and direct the beam into the medium energy 400[MeV] transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.5
6.03.03
The spin rotator quadrupoles after the Spin rotator solenoid shall be able to match the beam beta functions βx and βy to that required for entry into the 400MeV transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.6
6.03.03
The spin rotator exit quadrupoles shall have at least 2 families this is required to control the electron beam optics as needed.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.7
6.03.03
The spin rotator solenoid shall rotate the electron beam spin from the X axis to the vertical y-axis before it enters the medium [400MeV] transport line to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.8
6.03.03
The spin rotator solenoid shall have an integrated gradient of 2.2 [T.m] required to rotate the spin from the horizontal axis to the vertical axis.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.1
6.03.03
The bump magnets shall have a rise and time consistent with the requirements of the circulating bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ-MAG-BUMP.2
6.03.03
The Pulsed bump magnets shall be able to create a closed orbit path passing close to the Septum and maintain it during each injection cycle (100-150 Hz).
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.6
6.03.03
Each train of four bunches shall be injected into neighboring RF buckets to facilitate bunch merges.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.7
6.03.03
The injection system shall be capable of maintaining the small spacing required by the injected bunches.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.11
6.03.03
The injection system into the RCS shall be capable of injecting successive bunches into the RCS to create a bunch train with four bunches each circulating in the RCS ready to be merged.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-METL-RCS-INJ.12
6.03.03
The RCS shall be capable of merging each train of 4 bunches into a larger single bunch to create larger single circulating bunche in the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.2
6.03.03
The Medium energy transfer line shall contain 3 sections: 1. Spin rotation section, 2. The main transfer line, 3. The Injector system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.3
6.03.03
There will be number of corrector Quadrupoles after the Pre-Injector longitudinal matching and before the spin rotator to provide beam matching into the Spin Rotator.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.4
6.03.03
The medium energy 400 MeV transfer line shall be able to transport the spin reoriented beam from the spin rotator to the RCS injection system.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.5
6.03.03
The medium energy 400 MeV transfer line will maintain the spin direction of the beam along the entire transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.6
6.03.03
The spin rotator shall ensure the spin direction of the electron bunches are rotated from the longitudinal Z axis to the vertical Y axis.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH-INST.1
6.03.04
To characterize the beam as it enters the buncher section, there shall be beam position monitor (BPM), and a transverse profile monitor at the entry to the buncher cavity to measure beam loss, position, and charge.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.2
6.06.03
To control the beam and to measure bunch compression through the buncher section, there shall be an integrating current transformer (ICT), beam position monitors and transverse profile monitors
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-INST.3
6.06.03
To characterize the beam as it exits the buncher section, there shall be an emittance measurement including slit and beam viewer, an integrating current transformer, beam position monitor, charge and compression during commissioning.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH-RF.1
6.08
one 197 MHz buncher cavity shall be used for providing bunch chirp
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.2
6.08
The bunching section shall generate sufficient compression to compress the bunch length to that required by [5.9].
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.3
6.08
The bunchers rf voltage and phase will be synchronized so that the passing electron bunches meet the required beam characteristics at the end of the buncher section.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-BUNCH.4
6.08
The Pre-Injector layout shall accommodate all RF cavities and allow enough room for other Pre-Injector components.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-LINAC-VAC.1
6.03.04
The LINAC section shall contain enough strategically located Vacuum gate valves, to allow access to the vacuum volume as needed.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.1
6.03.03
The LTR transfer line shall terminate with an injection system capable of transferring the beam into the RCS for all the operating energies and conditions specified in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.3
6.03.03
The vertically spin polarized electron bunch patterns generated by the pre-injector shall be transferred into the RCS unaltered.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.1
6.08
There shall be a special RF kicker to kick the injected beam into neighboring RF buckets without disturbing the 8 circulating bunches.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ.1
6.03.04
The EIS Pre-Injector shall consist of 3 sub-systems: 1. An electron gun section, followed by 2. A low energy transfer line and bunching section, followed by 3. A LINAC section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-INST.1
6.03.04
EIS shall have all the beam instrumentation necessary to deliver the operational parameters set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-HETL-INST-BPM-ELEC.01
6.03.03.04.01
The BPM single bunch measurement resolution for a (1 - 4 nC) pilot bunch shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.02
6.03.03.04.01
The BPM single bunch measurement resolution for (5.5 - 28 nC) bunches shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.03
6.03.03.04.01
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.04
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used to measure the transport lattice.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.01
6.03.03.04.01
The BPM Pickup alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.02
6.03.03.04.01
The BPM Pickup shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.04
6.03.03.04.01
The BPM Pickups shall be located by the dipole correctors at every second quadrupole.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM-ELEC.01
6.03.03.04.01
For a (1 nC) pilot bunch, the BPM single bunch measurement resolution shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.02
6.03.03.04.01
For (5.5 - 10 nC) bunches, the BPM single bunch measurement resolution shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.03
6.03.03.04.01
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.04
6.03.03.04.01
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.01
6.03.03.04.01
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.02
6.03.03.04.01
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.04
6.03.03.04.01
The location of the BPM Pickups shall be TBD
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.01
6.03.02.05.04
A synchrotron light monitor (SLM) shall be installed in the RCS ring downstream of an RCS dipole magnet
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.02
6.03.02.05.04
The location of the SLM light extraction port shall be- TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.03
6.03.02.05.04
The synchrotron light shall be transported from the RCS light extraction port to an optical table for detection.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.04
6.03.02.05.04
The synchrotron light optical table shall have a streak camera and gated camera shall be installed.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.05
6.03.02.05.04
The SLM shall be able to make Turn-by-turn measurements using gated cameras to provide measurements of; the injection matching parameters and the beam position stability parameters during acceleration. TBD -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.06
6.03.02.05.04
The SLM shall be used to provide horizontal and vertical transverse profile measurements on bunches with charges > 6nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.07
6.03.02.05.04
The SLM horizontal and vertical transverse profile measurements shall be measured with a resolution in both planes of 0.1 mm
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.08
6.03.02.05.04
The SLM shall be used to provide longitudinal profile measurements
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.09
6.03.02.05.04
A dual sweep streak camera shall be used to provide measurements of the bunch length and longitudinal profiles
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.10
6.03.02.05.04
The dual sweep streak camera shall have a resolution of <5 ps
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.11
6.03.02.05.04
The profile measurements shall be used, together with modeled or measured beam optics to infer the beam emittances and energy spread.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.12
6.03.02.05.04
The Vertical emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.6 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.13
6.03.02.05.04
The Horizontal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 10 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.14
6.03.02.05.04
The Longitudinal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.00001 eV-s
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.15
6.03.02.05.04
The Energy spread measurement, for bunch charges > 6nC, shall be measured with a precision of 0.0001 dp/p
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.01
6.04.06.02
A bunch pattern monitor shall be installed in the ESR to measure indiviual bunch charge with an accuracy 1 %
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.02
6.04.06.02
The Bunch pattern monitor shall be capable of measuring Bunch patterns ranging from a single bunch, to a filled ring with 1,160 bunches
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.01
6.04.06.05
BLM shall be needed to needed to protect sensitive equipment.
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.02
6.04.06.05
The number of BLM installed in the ESR shall be TBD ea
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.03
6.04.06.05
BLM shall be installed at the following locations in the ESR TBD
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.04
6.04.06.05
The sensitivity of the BLM detectors shall be TBD units?
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.05
6.04.06.05
Where possible existing RHIC BLM's can be relocated to identify ESR & HSR losses
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.06
6.04.06.05
The response time from loss detection to abort shall be TBD us
05/16/2025
In Process
FALSE

P-ESR-INST-BPM-ELEC.01
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following capabilities defined for the low intensity pilot injection energies and high intensity collision energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following time resolutions for data refresh defined for the beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.03
6.04.06.01
The ESR BPM Electronics shall have the following time resolutions for data logging defined for the beam energies:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.04
6.04.06.01
The ESR BPM Electronics shall have the following measurement resolutions defined for beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.05
6.04.06.01
The ESR BPM Electronics shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.06
6.04.06.01
The ESR BPM Electronics shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-PU.01
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall provide dual plane (horizontal and vertical) beam positional measurements.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) shall be positioned in the following locations approved by physics as defined in the lattice:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.03
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) mechanical and electrical center in the locations identified shall be:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.04
6.04.06.01
The ESR Beam Position Monitor Pick-Ups housing shall have a +/- 10 (mrad) corresponding to +/- 0.6 (degree) roll tolerance with regards to BPM measurements in respect to the vacuum chamber.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.05
6.04.06.01
The ESR Beam Position Monitor Pick-Ups design shall be less than or equal to the allocated impedance and is within the accepted overall ESR impedance budget approved by physics. (replace with loss factor)
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.06
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall fulfill resolution requirements over the horizontal and vertical beam position range with respect to its fiducials of +/- 3 (mm).
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.07
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to ensure the maximum temperatures of the components (due to heating by the beam) are acceptable for reliability and operations of the EIC over the planned operational life of 20 (yrs).
09/15/2025
In Process
FALSE

P-ESR-INST-BPM-PU.09
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to be baked to 250 °C for UHV processing.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.10
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.11
6.04.06.01
The ESR BPM Pickup shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/30/2025
In Process
FALSE

P-ESR-INST-BPM-PU.12
6.04.06.01
The ESR Beam Position Monitor Button configuration will be mirror symmetric with respect to the mid-and center planes. Deviation from symmetry shall be such that corresponding BPM reading errors are less then 20 microns.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.13
6.04.06.01
The ESR Beam Position Monitor Pick-Ups symmetrical configuration (postion between the four buttons and the relative to the fiducials on top of the button) shall be stable under the inference of the expected operational thermal changes to the extent that corresponding changes in the bpm reading deviate less than 20 µm.
07/25/2025
Approved
FALSE

P-ESR-INST-DCCT.01
6.04.06.02
A DCCT shall measure the average beam current in the ESR.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.02
6.04.06.02
The measurement resolution averaged over 1 sec shall be < 5 uA
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.03
6.04.06.02
The DCCT beamline device impedance shall be approved by beam physics.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.04
6.04.06.02
Measurement drift tolerance (thermal effects) shall be ≤ 1 uA/K
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.05
6.04.06.02
The DCCT sensor in the ring shall operate in the temperature range of 15 to 35 degrees C
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.06
6.04.06.02
The range of average beam current to be measured shall be 0.156x10-3 to 2.5 A
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.07
6.04.06.02
The DCCT system shall have a remote controlled self calibration system
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.08
6.04.06.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.09
6.04.06.02
The measured average current shall be provided to users at a rate of 10 Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.10
6.04.06.02
The measured average current shall be archived at a rate of 10 Hz Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.11
6.04.06.02
The DCCT sensor assembly in the ring shall be radiation resistant
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.01
6.04.06.03
The requirements for longitudinal feedback are ??? TBD
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.02
6.04.06.03
The Longitudinal feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.01
6.04.06.04
The ESR shall have two synchrotron light monitors (SLM) and one X-ray pin hole monitor
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.02
6.04.06.04
The longitudinal bunch profile monitor shall have a turn-by-turn capability based on a single bunch in the fully filled bunch train.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.03
6.04.06.04
TThe SLM systems shall measure the crabbing angle, longitudinal bunch parameters, H & V beam size and global coupling.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.04
6.04.06.04
The SLM shall be able to measure a crabbing angle of 12.5 mrad with accuracy of 10 %
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.05
6.04.06.04
The SLM shall be able to measure the Longitudinal bunch parameters with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.06
6.04.06.04
The SLM shall be able to measure the H & V beam size with accuracy of H=?? V=?? units
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.07
6.04.06.04
The SLM shall be able to measure the Global coupling with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.08
6.04.06.04
One SLM port shall be located downstream of a dipole in an appropriate location in the ESR, exact location not critical.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.09
6.04.06.04
The second SLM port shall be located in a complimentary location in the lattice to ensure all the necessary SLM measurements can be made. TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.10
6.04.06.04
The SLM light extraction port mirrors shall be good quality, having a surface finish better than 1/10 Lambda
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.11
6.04.06.04
The SLM light extraction port mirrors shall be water cooled to avoid image distortion.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.12
6.04.06.04
There shall be an enclosed SL transport from the light extraction port to the SLM optical lab rooms. Length to be determined by the distance to optical lab room, should be minimized to reduce vibration problems.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.13
6.04.06.04
The locations of the SLM optical lab rooms shall be TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.14
6.04.06.04
The double-slit interferometer method shall be used to measure transverse beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.15
6.04.06.04
The standard transverse resolution of an SLM using visible light shall be ~60 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.16
6.04.06.04
The resolution using the double-slit method shall equal to 10 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.17
6.04.06.04
A streak camera shall be used to measure the bunch longitudinal profiles
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.18
6.04.06.04
A position sensitive photo-diode will provide photon beam centroid information which shall supplement the orbit stability measurements by the BPMs
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.19
6.04.06.04
A GigE CCD/CMOS camera, externally triggerable with exposure times ranging from 10 nsec to 5 sec, shall be used to image the visible radiation
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.20
6.04.06.04
A commercially available gated camera with gate width of <2 nsec (compared to a minimum bunch spacing of 10 nsec) shall be used to detect injection oscillations and for beam studies.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.21
6.04.06.04
The location of the X-ray pinhole monitoring system shall be TBD
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.22
6.04.06.04
The target resolution of the X-ray pin hole monitoring system shall be ~ 5 um (or as best that can be achieved with the machine parameters and commercial equipment) 5 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.23
6.04.06.04
The X-ray pin hole monitor shall provide independent measurement of the energy spread and horizontal/vertical emittance. H=V=15.4 nm
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.24
6.04.06.04
The X-ray pinhole photon beamline shall be equipped with gated cameras that will be employed to provide high resolution turn-by-turn profile measurements
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.25
6.04.06.04
A pinhole assembly including tungsten slits shall provide sufficient resolution to precisely measure the beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.26
6.04.06.04
Several different size pinholes sizes shall be incorporated to allow easy alignment and measurements at different beam currents and energies.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.01
6.04.06.03
Stripline kickers (H & V) shall be used to excite the beam so tunes can be measured using turn-by-turn BPM data.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.02
6.04.06.03
The magnitude of the kick required for the horizontal kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.03
6.04.06.03
The magnitude of the kick required for the vertical kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.04
6.04.06.03
The kicker waveform (risetime and shape) requirements shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.05
6.04.06.03
The location of the tune meter kicker striplines in the ESR shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.06
6.04.06.03
The impedance of the kicker beamline device shall be approved by beam Physics.
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.01
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.03
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.02
6.04.06.03
The transverse feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSSLFB.01
6.04.06.03
The transverse slow feedback system bandwidth shall bs 10 Hz
05/16/2025
In Process
FALSE

F-EIS-LINAC-MAG-QUAD.3
6.03.04
A drift space with quadrupole triplets shall be placed between each TWP structure to tune the bunch beta function through the LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-CHIRP.1
6.03.04
Following the Zigzag there shall be a de-chirp cavity to linearize and reduce the energy spread of the bunch.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-DIP.1
6.03.04
The ZigZag section shall consist of a number of dipoles separated by drift spaces in a R56 configuration to increase the bunch length to 40ps.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG-MAG-QUAD.1
6.03.04
The ZigZag section shall consist of a number of Quadrapoles to control the beam dispersion through the zigzag.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.1
6.03.04
A longitudinal matching section shall follow the S-band LINAC.
05/16/2025
Not Applicable
FALSE

F-EIS-LINAC-ZIGZAG.3
6.03.04
At the Zigzag exit, the electron beam’s average spin orientation shall be longitudinal in the direction of beam travel.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-INJ-MAG-FKICK.1
6.03.03
The fast kicker magnet shall be capable of deflecting the electron beam from the RCS to counter the RF kick.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.4
6.03.03
The spin rotator entry quadrupole shall have at least 2 families this is needed to control the electron beam optics as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL.1
6.03.03
The Medium energy transfer line shall transfer the beam from the pre-injector longitudinal matching section to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ-BUNCH.1
6.03.03
The pre-injector LEBT low energy RF section shall transfer the electron beam from the gun to the linac section. shall provide bunching and initial acceleration to each 1 nC bunch
05/16/2025
In Process
FALSE

F-EIS-PREINJ-GUN.2
6.03.04
The pre-injector electron gun shall produce all the bunch patterns required to deliver the ESR beam requirements set forth in [5.9].
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.21
6.03.04
The diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.1
6.03.03
The pre-injector shall have a low energy transfer line from the gun into the beam compression "Bunching" section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.6
6.03.04
Following the gun, there shall be multiple groups of magnets required to control the electron beam.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.7
6.03.04
To characterize and control the fresh bunches the low energy transfer line from the Gun to the Buncher shall contain a plunging transverse profile monitor, a bunch charge monitor, beam loss monitors, and beam position monitors
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-TLINE-MEBT-MAG-QUAD.1
6.03.03
The corrector Quadrupoles shall be able to suppress the βx and βy along the transfer line to levels consistent with those required ate the RCS injection kicker.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-SEP.1
6.03.03
The septum magnet shall be capable of deflecting the incoming electron beam into the RCS and shielding the circulating beam already in the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.2
6.03.03
The injection system shall inject the beam at Need update
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.4
6.03.03
The injection system shall be able to inject one bunch per injection kick using RF and magnetic kickers to build up a total of 8 bunches from 4 kicks to the RF and kickers.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.5
6.03.03
The injection system shall ensure the bunch emittance shall match the requirements of the RCS RF system and such, to avoid collective instabilities and to stay within the off-momentum aperture.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.9
6.03.03
The injection system shall contain 3 bump magnets to locally bump the RCS circulating beam close to the injection septum.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.10
6.03.03
The RCS injection system shall contain an RF kicker and a pulsed magnet followed by a septum magnet to redirect the beam into the RCS closed orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR.11
6.03.03
The magnetic field of the injection system pulsed magnet shall follow the rise time of the power amplifiers which drive the RF kickers..
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.01
6.03.03.05.01
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.02
6.03.03.05.01
The dimension in W shall be 3 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.03
6.03.03.05.01
The dimension in L shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.04
6.03.03.05.01
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.05
6.03.03.05.01
The num magnets shall be 3
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.06
6.03.03.05.01
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.07
6.03.03.05.01
The rise time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.08
6.03.03.05.01
The fall time shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.09
6.03.03.05.01
The flat top time shall be 0.05 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.10
6.03.03.05.01
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.11
6.03.03.05.01
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.12
6.03.03.05.01
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.13
6.03.03.05.01
The deflecting Angle shall be tbd (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.14
6.03.03.05.01
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.15
6.03.03.05.01
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.16
6.03.03.05.01
The output current spec shall be 425 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.17
6.03.03.05.01
The inductance with cable shall be 6 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_KICK.18
6.03.03.05.01
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.01
6.03.03.05.02
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.02
6.03.03.05.02
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.03
6.03.03.05.02
The dimension in L shall be 8 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.04
6.03.03.05.02
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.05
6.03.03.05.02
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.06
6.03.03.05.02
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.07
6.03.03.05.02
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.08
6.03.03.05.02
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.09
6.03.03.05.02
The flat top time shall be 0.005 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.10
6.03.03.05.02
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.11
6.03.03.05.02
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.12
6.03.03.05.02
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.13
6.03.03.05.02
The deflecting Angle shall be 30 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.14
6.03.03.05.02
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.15
6.03.03.05.02
The output voltage Spec shall be 30 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.16
6.03.03.05.02
The output current spec shall be 530 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.17
6.03.03.05.02
The inductance with cable shall be 12.5 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_PULSE_SEPT.18
6.03.03.05.02
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.2
6.08
The special kicker shall consist of an RF harmonic kicker with fundamental frequency of 1/4 of the main RCS RF cavity or compatible equivalent alternative.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.3
6.08
The special kicker shall have a rise and fall time that matches the RF bucket size.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.4
6.08
The special kicker shall have a peak power necessary to generate a kick to inject the bunch into the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.5
6.08
The special kicker shall have a macro pulse with a flattop that is greater than the time between the LINAC bunches and shall have a rise and fall time less than 1 RCS turn.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.6
6.08
The special kicker shall be able to repeat at the LINAC pulse rate.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT.28
6.03.03
The LTR transfer line shall have several FODO quadrupoles to control the beta function along the transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-PREINJ.3
6.03.04
The EIS Pre-Injector shall create bunches which meet the requirements set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-RCS-MAG-QUAD.5
6.03.02
The quadrupoles shall be individually powered with low supplementary current/voltage power supplies for beam-based alignment purposes.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.7
6.03.02
The RCS straight sections shall have the appropirate number of defocusing and focusing quadrupole families per straight section.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.9
6.03.02
The non-colliding straights will have different scheme.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.14
6.03.02
The main arc quadrupoles shall be powered by a total of 2 power circuits 1 for focusing the other defocusing.
05/16/2025
In Process
FALSE

F-EIS-RCS-MAG.15
6.03.02
The quadrupoles in both straight sections shall need a total of 6 power circuits to power all six families of quadrupoles in both straights. (straights are optically identical)
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.18
6.03.02
The RCS magnets shall be fed by a system of power supplies matched in voltage and maximum current to the specifications and requirements of the respective magnets.
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-BUMP.1
6.03.03
the RCS extraction system shall have three fast bump magnets to direct the bunches to the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-FKICK.1
6.03.03
RCS extraction shall be facilitated with a fast kicker having a rise time of 2 micro-secs
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker shall operate in unison with a septum magnet which can direct the beam into the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.1
6.03.03
The beam injection of the electron bunches from the RCS into the ESR ring shall take place in the 12 o’clock straight section.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-PPD.2
6.03.03
There will be two electron bunches circulating in the RCS at extraction, these shall be injected into the High Energy Transfer Line which connects the RCS to the ESR.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.01
6.03.03.05.03
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.02
6.03.03.05.03
The dimension in W shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.03
6.03.03.05.03
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.04
6.03.03.05.03
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.05
6.03.03.05.03
The num magnets shall be 3 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.06
6.03.03.05.03
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.07
6.03.03.05.03
The rise time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.08
6.03.03.05.03
The fall time shall be 0.001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.09
6.03.03.05.03
The flat top time shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.10
6.03.03.05.03
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.11
6.03.03.05.03
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.12
6.03.03.05.03
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.13
6.03.03.05.03
The deflecting Angle shall be 1.2 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.14
6.03.03.05.03
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.15
6.03.03.05.03
The output voltage Spec shall be 50 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.16
6.03.03.05.03
The output current spec shall be 600 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.17
6.03.03.05.03
The inductance with cable shall be 26 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_KICK.18
6.03.03.05.03
The cooling type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.1
6.08
The RF system shall Provide a maximum RF voltage of 60MV to accelerate the beam.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.2
6.08
The total RF power provided by the RF amplifiers shall be able to compensate for all additional losses created by the stored electron beam in addition to the acceleration and synchrotron losses.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.3
6.08
The RF system shall Provide sufficient gradient to allow installation of all necessary RF modules in the limited space in IR 10.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.4
6.08
The RF system shall be able to accommodate 4 circulating bunches in one trains of 4 bunches.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.5
6.08
The RF system shall be able to merge the one train of 4 bunches into two larger separate circulating bunches then merge these two large bunches into a single larger circulating bunch.
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.6
6.08
The RF system shall be able to accelerate final large, merged bunch to the operating energies needed by the ESR as set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS-RF.7
6.03.02
The RF system controls shall be designed to handle the transient beam loading for all bunch structures.
05/16/2025
In Process
FALSE

F-EIS-RCS-VAC.1
6.03.02
The vacuum chamber shall provide sufficient horizontal and vertical aperture to accommodate a beam which is 5 σ larger than the largest sigma beam size determined by the injected RMS emittance.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.2
6.03.02
The average dynamic pressure around the ring shall be < 5e-8[Torr] after 1 year of operation.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.3
6.03.02
The impedance of the entire RCS vacuum system shall allow for the bunch intensities, beam currents, and bunch numbers contained in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.09
6.03.02.04
The vacuum chamber shall be capable of absorbing and carrying away the eddy current power.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.4
6.03.02
The vacuum chamber and all its components shall be designed to withstand the total synchrotron radiation loads seen in operation.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-VAC.08
6.03.02.04
The vacuum chamber shall be capable of absorb synchrotron radiation and carrying away the absorbed power.
05/16/2025
Approved
FALSE

F-EIS-RCS.1
6.03.02
The RCS shall consist of two parts 1. The main RCS Ring, and 2. The High energy transfer line terminating with the ESR injection system
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.2
6.03.03
The RCS shall be capable of accepting the bunches and matching the bunch parameters as injected by the BAR into the LTR transfer line.
05/16/2025
In Process
FALSE

F-EIS-RCS.3
6.03.02
After bunch injection into the RCS, the RCS shall merge the injected bunches into two bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.4
6.03.02
After bunch injection the RCS shall be able to accelerate the single bunch to the final desired energy set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS.5
6.03.02
The RCS needs to accelerate to the top possible energy in a time interval consistent with the parameters set forth in [5.9] at approximately 100 msecs for 18 GeV.
05/16/2025
In Process
FALSE

F-EIS-RCS.6
6.03.03
The RCS shall be capable of kicking the accelerated bunches into the RTE transfer line to the ESR.
05/16/2025
In Process
FALSE

F-EIS-RCS.7
6.03.02
RCS will need to increase the vertical emittance to match the ESR vertical emittance.
05/16/2025
In Process
FALSE

F-EIS-RCS.8
6.03.02
The RCS shall have a racetrack design with 160 arc FODO cells, bending radius of 91.67 m and two 86.624 m straight sections made up of 8 FODO cells with a total circumference of 1.421 km
05/16/2025
In Process
FALSE

F-EIS-RCS.12
6.03.02
The alignment of the dipole field with respect to the vertical axis shall be less +/- 1 mrad rms with 2 sigma cut-off.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS-RCS.15
6.03.02
The RCS lattice shall contain provisions for correctors such as dipole correctors etc., as needed.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS-TLINE-GUN-Diagnostic.1
6.03.04
The Pre-injector separate diagnostic beamline section shall have 3 branches one with Faraday cup, one port containing a connection to the cathode Laser and a line to a low energy beam dump.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.1
6.03.04
The instrumentation in the diagnostic beamline to the low energy beam dump shall have the capability to measure beam position, profile, bunch charge
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.4
6.03.04
The Faraday cup shall be able to measure the charge of the electron bunches from the gun.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-LASER-INST.1
6.03.04
There shall be instrumentation capable of measuring the position and profile of the laser beam on the cathode.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-LASER.1
6.03.04
The laser beam shall illuminate the cathode perpendicular to the cathode face
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.1
6.03.04
The beam tube and flange sizes shall be appropriate to transport polarized e-beam between the e-source and the diagnostic beam line polarimeter chamber.
05/16/2025
In Process
FALSE

F-EIS-TLINE-GUN-VAC-Diagnostic.2
6.03.04
Vacuum system shall be compatible with UHV requirements.
05/16/2025
Not Applicable
FALSE

F-EIS-TLINE-SPIN.INST.1
6.03.03
Profile monitor, BPM are placed at before, in between and after two Wien filters
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.1
6.03.03
Between the dipole chamber and the bunching section, two Wien filters shall be used as spin rotator to rotate the spin direction from longitudinal to vertical.
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.2
6.03.03
triplets focusing are used in between the two Wien filters to maintain the beam envolop
05/16/2025
In Process
FALSE

F-EIS-TLINE-SPIN.3
6.03.03
Quadpole single let and double let are used before and after Wien to compensate the quadropole components from the Wien entrance and exit
05/16/2025
In Process
FALSE

F-EIS-VAC.1
6.03.04
The EIS vacuum system shall meet UHV standards at a minimum (Ref vacuum spec?)
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.07
6.03.02.04
On 15 m on each side (or one vacuum section) of the SRF cavities the vacuum system shall be processed to class ISO 5.
05/16/2025
Approved
FALSE

F-EIS-VAC.3
6.03.04
The size, location and type of vacuum pumps shall be chosen to meet the required vacuum levels during operation
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-VAC.4
6.03.04
Appropriate vacuum gauging shall be supplied in each vacuum sector to monitor the required vacuum levels
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

G-EIS.12
6.03
The ESR bunch replacement pattern shall accommodate the RF cogging limitations incurred by any beam transfer between RCS and ESR.
05/16/2025
Approved
FALSE

F-EIS.1
6.03.04
The EIS polarized electron source shall create a spin polarized beam of electrons and inject them into the ESR.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS.2
6.03.04
The injected spin polarized electron beam shall meet all the parameters set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS.3
6.03.04
The EIS shall consist of five sections: 1. Pre-Injector 2. LTR Transfer Line 3. BAR 4. RCS 5. RTE Transfer Line
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

EIS EXTERNALS
Requirements who's parents are in other sub-systems.

G-EIS.3x
6.03
All EIS components and systems shall be designed and installed in line with all relevant relagutaory codes and in full compliance with BNL SBMS.
05/16/2025
Not Applicable
FALSE

F-EIS-HETL-ESR-INJ.2
6.03.03
Each electron bunch from the transfer line shall be injected into ESR in its own injection cycle. In a manner that minimizes the background on the detector system.
05/16/2025
Not Applicable
FALSE

F-EIS-PROT-ABORT.2
6.06.03
The RCS beam abort system shall have a beam inhibit interlock to prevent the Pre-Injector injecting fresh bunches into the RCS under fault conditions.
05/16/2025
In Process
FALSE

F-EIS-PROT-ABORT.1
6.06.03
The RCS shall have a beam abort system which will use a soft dump process that does not require a dedicated beam dump.
05/16/2025
In Process
FALSE

F-EIS-PROT-COLL.1
6.06.03
The RCS shall have a collimation system to protect all other apertures in the RCS.
05/16/2025
In Process
FALSE

F-EIS-PROT-DUMP.1
6.06.03
The Pre-Injector shall have strategically placed beam dumps for machine protection, commissioning and diagnostics as required.
05/16/2025
In Process
FALSE

F-EIS.2x
6.06.03
The EIS shall contain an Abort system to dump the beam and protect the system when required
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-VAC.08
6.03.03.03
Fast valve protection shall be provided at TBD
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.08
6.03.03.03
Fast valve protection shall be provided at TBD
05/16/2025
On Hold
FALSE

EIS-RCS : Rapid Cycling Synchrotron (WBS 6.03.02)

F-EIS-RCS.9
6.03.02
The RCS lattice shall provide a maximum dynamic aperture of 3 sigma w.r.t Gaussian electron beam distribution in transverse dimensions.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS-RCS.10
6.03.02
The RCS off-momentum aperture shall reach 1.0% dp/p.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS-RCS.11
6.03.02
Quadrupoles and sextupoles shall be aligned to with 0.2 mm RMS or better with a 2.5 sigma cutoff.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS-RCS.16
6.03.02
The RCS ring shall be situated below the ESR ring to avoid any physical interference with any other systems.
05/16/2025
Not Applicable
FALSE

EIS-RCS EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-RCS.1
6.03.02
The RCS shall consist of two parts 1. The main RCS Ring, and 2. The High energy transfer line terminating with the ESR injection system
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.2
6.03.03
The RCS shall be capable of accepting the bunches and matching the bunch parameters as injected by the BAR into the LTR transfer line.
05/16/2025
In Process
FALSE

F-EIS-RCS.3
6.03.02
After bunch injection into the RCS, the RCS shall merge the injected bunches into two bunches.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS.4
6.03.02
After bunch injection the RCS shall be able to accelerate the single bunch to the final desired energy set forth in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS.5
6.03.02
The RCS needs to accelerate to the top possible energy in a time interval consistent with the parameters set forth in [5.9] at approximately 100 msecs for 18 GeV.
05/16/2025
In Process
FALSE

F-EIS-RCS.6
6.03.03
The RCS shall be capable of kicking the accelerated bunches into the RTE transfer line to the ESR.
05/16/2025
In Process
FALSE

F-EIS-RCS.7
6.03.02
RCS will need to increase the vertical emittance to match the ESR vertical emittance.
05/16/2025
In Process
FALSE

F-EIS-RCS.8
6.03.02
The RCS shall have a racetrack design with 160 arc FODO cells, bending radius of 91.67 m and two 86.624 m straight sections made up of 8 FODO cells with a total circumference of 1.421 km
05/16/2025
In Process
FALSE

F-EIS-RCS.12
6.03.02
The alignment of the dipole field with respect to the vertical axis shall be less +/- 1 mrad rms with 2 sigma cut-off.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS-RCS.13
6.03.02
The RCS shall reach an availability consistent with the overall availability of the entire EIC as specified in [5.9].
05/16/2025
In Process
FALSE

F-EIS-RCS.14
6.03.02
The RCS shall transmit polarization with a 97% efficiency
05/16/2025
In Process
FALSE

F-EIS-RCS.15
6.03.02
The RCS lattice shall contain provisions for correctors such as dipole correctors etc., as needed.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

EIS-RCS-MAG : EIS RCS Magnet (WBS 6.03.02.02)

F-EIS-RCS-MAG.x1
6.03
The RCS dipole shall be an RBEND C-shaped dipole with 1.8 m long core with a bending radius of 91.67 m for an angular beam deflection of 0.01963 rad. To control the magnet temperature during ramping it shall be water cooled. There shall be a total of 320 dipole magnets in the RCS lattice.
08/20/2025
In Process
FALSE

F-EIS-RCS-MAG.1
6.03.02
The magnets shall meet the requirements defined by the physics lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS-RCS-MAG.5
6.03.02
The EIC RCS lattice arc FODO cells shall consist of a horizontally focusing\defocusing quadrupole magnet followed by a correction dipole, then a followed by a sextupole correction magnet and a dipole bending magnet. With a drift space between these elements of > 0.3m long.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS-RCS-MAG.6
6.03.02
There shall be sections at the ends of the ARCS and the straight sections to match the optics.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS-RCS-MAG.10
6.03.02
The straight sections IR2,4,10 and 12 shall use FODO cells for optic control.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS-RCS-MAG.13
6.03.02
There shall be only one family of dipoles in the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS-RCS-MAG.17
6.03
Sextupoles shall be powered based on their “families” with the family structure dependent on the linear lattice configuration for arcs and straight sections.
08/20/2025
In Process
FALSE

EIS-RCS-MAG EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-RCS-MAG.7
6.03.02
The RCS straight sections shall have the appropirate number of defocusing and focusing quadrupole families per straight section.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.9
6.03.02
The non-colliding straights will have different scheme.
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.14
6.03.02
The main arc quadrupoles shall be powered by a total of 2 power circuits 1 for focusing the other defocusing.
05/16/2025
In Process
FALSE

F-EIS-RCS-MAG.15
6.03.02
The quadrupoles in both straight sections shall need a total of 6 power circuits to power all six families of quadrupoles in both straights. (straights are optically identical)
05/16/2025
Not Applicable
FALSE

F-EIS-RCS-MAG.18
6.03.02
The RCS magnets shall be fed by a system of power supplies matched in voltage and maximum current to the specifications and requirements of the respective magnets.
05/16/2025
In Process
FALSE

EIS-RCS-MAG-C0 : EIS RCS Magnet C0 (WBS 6.03.02.01)

EIS-RCS-MAG-C0 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

EIS-RCS-MAG-Q0 : EIS RCS Magnet Q0 (WBS 6.03.02.01)

EIS-RCS-MAG-Q0 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

EIS-RCS-MAG-Q0_6 : EIS RCS Magnet Q0_6 (WBS 6.03.02.01)

EIS-RCS-MAG-Q0_6 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

EIS-RCS-MAG-S0 : EIS RCS Magnet S0 (WBS 6.03.02.01)

EIS-RCS-MAG-S0 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

EIS-RCS-MAG-D0 : EIS RCS Magnet D0 (WBS 6.03.02.02)

P-EIS-RCS-MAG-D0.21.3
6.03.02.02
-5 < b3 < 3 , 0.9 < a3 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.10
6.03.02.02
-1 < b10 < 1 , 0.9 < a10 < 1.1
05/16/2025
Approved
FALSE

EIS-RCS-MAG-D0 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

EIS-RCS-MAG-CORR : RCS Corrector Magnet

EIS-RCS-MAG-DIP : RCS Dipole Magnet

EIS-RCS-MAG-PS : RCS Magnet Power Supply

EIS-RCS-MAG-QUAD : RCS Quadrupole Magnet

EIS-RCS-MAG-SEXT : RCS Sextupole Magnet

EIS-RCS-PS : EIS RCS Magnet Power Supply (WBS 6.03.02.03)

EIS-RCS-PS-C0 : EIS RCS Magnet Power Supply C0 (WBS 6.03.02.03)

EIS-RCS-PS-C0 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-RCS-PS-CO : EIS RCS Magnet Power Supply CO (WBS 6.03.02.03)

EIS-RCS-PS-D0 : EIS RCS Magnet Power Supply D0 (WBS 6.03.02.03)

EIS-RCS-PS-D0 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-RCS-PS-Q0 : EIS RCS Magnet Power Supply Q0 (WBS 6.03.02.03)

EIS-RCS-PS-Q0_6 : EIS RCS Magnet Power Supply Q0_6 (WBS 6.03.02.03)

EIS-RCS-PS-Q0_6 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-RCS-PS-S0 : EIS RCS Magnet Power Supply S0 (WBS 6.03.02.03)

EIS-RCS-PS-SXT : EIS RCS Magnet Power Supply SXT (WBS 6.03.02.03)

EIS-RCS-PS-SXT EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-RCS-VAC : EIS RCS Vacuum (WBS 6.03.02.04)

P-EIS-RCS-VAC.04
6.03.02.04
The acceptable magnetic field from vacuum equipment within a radius 16mm (wrt Beam center) shall be TBD Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.05
6.03.02.04
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
Approved
FALSE

EIS-RCS-VAC EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-RCS-VAC.1
6.03.02
The vacuum chamber shall provide sufficient horizontal and vertical aperture to accommodate a beam which is 5 σ larger than the largest sigma beam size determined by the injected RMS emittance.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.2
6.03.02
The average dynamic pressure around the ring shall be < 5e-8[Torr] after 1 year of operation.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.3
6.03.02
The impedance of the entire RCS vacuum system shall allow for the bunch intensities, beam currents, and bunch numbers contained in [5.9].
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.09
6.03.02.04
The vacuum chamber shall be capable of absorbing and carrying away the eddy current power.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-RCS-VAC.4
6.03.02
The vacuum chamber and all its components shall be designed to withstand the total synchrotron radiation loads seen in operation.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-VAC.08
6.03.02.04
The vacuum chamber shall be capable of absorb synchrotron radiation and carrying away the absorbed power.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.07
6.03.02.04
On 15 m on each side (or one vacuum section) of the SRF cavities the vacuum system shall be processed to class ISO 5.
05/16/2025
Approved
FALSE

EIS-RCS-INST : EIS RCS Instrumentation (WBS 6.03.02.05)

EIS-RCS-INST-BPM : EIS RCS Instrumentation Beam Position Monitor (WBS 6.03.02.05)

EIS-RCS-INST-BPM-ELEC : EIS HETL Instrumentation Beam Profile Monitor Electronic (WBS 6.03.02.05.01)

EIS-RCS-INST-BPM-ELEC EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

EIS-RCS-INST-BPM-PU : EIS RCS Instrumentation Beam Profile Monitor Pick-Up (WBS 6.03.02.05.01)

EIS-RCS-INST-CM : EIS RCS Instrumentation Current and Charge Monitor (WBS 6.03.02.05)

EIS-RCS-INST-CM EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

EIS-RCS-INST-SLM : EIS RCS Instrumentation Synchrotron Light Monitor (WBS 6.03.02.05)

EIS-RCS-INST-SLM EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-INST-SLM.01
6.03.02.05.04
A synchrotron light monitor (SLM) shall be installed in the RCS ring downstream of an RCS dipole magnet
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.02
6.03.02.05.04
The location of the SLM light extraction port shall be- TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.03
6.03.02.05.04
The synchrotron light shall be transported from the RCS light extraction port to an optical table for detection.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.04
6.03.02.05.04
The synchrotron light optical table shall have a streak camera and gated camera shall be installed.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.05
6.03.02.05.04
The SLM shall be able to make Turn-by-turn measurements using gated cameras to provide measurements of; the injection matching parameters and the beam position stability parameters during acceleration. TBD -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.06
6.03.02.05.04
The SLM shall be used to provide horizontal and vertical transverse profile measurements on bunches with charges > 6nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.07
6.03.02.05.04
The SLM horizontal and vertical transverse profile measurements shall be measured with a resolution in both planes of 0.1 mm
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.08
6.03.02.05.04
The SLM shall be used to provide longitudinal profile measurements
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.09
6.03.02.05.04
A dual sweep streak camera shall be used to provide measurements of the bunch length and longitudinal profiles
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.10
6.03.02.05.04
The dual sweep streak camera shall have a resolution of <5 ps
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.11
6.03.02.05.04
The profile measurements shall be used, together with modeled or measured beam optics to infer the beam emittances and energy spread.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.12
6.03.02.05.04
The Vertical emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.6 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.13
6.03.02.05.04
The Horizontal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 10 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.14
6.03.02.05.04
The Longitudinal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.00001 eV-s
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.15
6.03.02.05.04
The Energy spread measurement, for bunch charges > 6nC, shall be measured with a precision of 0.0001 dp/p
05/16/2025
In Process
FALSE

EIS-RCS-INST-TM : EIS RCS Instrumentation Tune Monitor (WBS 6.03.02.05)

EIS-RCS-INST-TPM : EIS RCS Instrumentation Transverse Profile Monitor (WBS 6.03.02.05)

EIS-RCS-INST-BBA : RCS Beam Based Alignment Monitor

EIS-RCS-INST-BC : RCS Bunch Charge Monitor

EIS-RCS-INST-BCM : RCS Beam Current Monitor

EIS-RCS-INST-BLM : RCS Beam Loss Monitor

EIS-RCS-INST-BP : RCS Bunch Profile Monitor

EIS-RCS-INST-TLINE

EIS-RCS-INST-TLINE-HEBT

EIS-RCS-INST-TLINE-HEBT-INST

EIS-RCS-INST-TUNE : RCS Tune Monitor

EIS-RCS-PPD : EIS Pulsed Power Device System (WBS 6.03.03.05)

EIS-RCS-PPD-INJ_PULSE_KICK : EIS RCS Injection Pulse Power Kicker System (WBS 6.03.03.05.01)

EIS-RCS-PPD-INJ_PULSE_SEPT : EIS RCS Injection Pulsed Power Septum System (WBS 6.03.03.05.02)

EIS-RCS-PPD-EXT_PULSE_KICK : EIS RCS Extraction Pulse Power Kicker System (WBS 6.03.03.05.03)

EIS-RCS-PPD-EXT_RF_KICK : EIS RCS Extraction Pulse Power System (WBS 6.03.03.05.04)

EIS-RCS-PPD-EXT_RF_KICK EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

EIS-RCS-PPD-INJ_RF_KICK : EIS RCS Injection Pulse Power System (WBS 6.03.03.05.04)

EIS-RCS-PPD-INJ_RF_KICK EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

EIS-RCS-PPD-EXT_PULSE_SEPT : EIS RCS Extraction Pulsed Power Septum System (WBS 6.03.03.05.05)

EIS-RCS-PPD-BUMP : RCS Extraction System Bump Magnet

EIS-RCS-PPD-FKICK : RCS Extraction System Fast Kicker Magnet

EIS-RCS-PPD-FKICK EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-RCS-PPD-FKICK.1
6.03.03
RCS extraction shall be facilitated with a fast kicker having a rise time of 2 micro-secs
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 15 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.000002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.00000001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.10
6.03.03.05.04
The waveshape shall be 2 pulses/cycle
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1.2 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_RF_KICK.18
6.03.03.05.04
The cooling type type shall be water
05/16/2025
In Process
FALSE

EIS-RCS-PPD-SEPT : RCS Extraction System Septum Magnet

EIS-RCS-PPD-SEPT EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-RCS-PPD-SEPT.1
6.03.03
The fast bump magnets and Fast Kicker shall operate in unison with a septum magnet which can direct the beam into the HETL.
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.01
6.03.03.05.05
The location (Section) type shall be 12 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.02
6.03.03.05.05
The dimension in W type shall be 4 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.03
6.03.03.05.05
The dimension in L type shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.04
6.03.03.05.05
The dimension in H type shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.05
6.03.03.05.05
The num magnets type shall be 2 -
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.06
6.03.03.05.05
The mag gap type shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.07
6.03.03.05.05
The rise time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.08
6.03.03.05.05
The fall time type shall be 0.002 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.09
6.03.03.05.05
The flat top time type shall be 0.0015 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.10
6.03.03.05.05
The waveshape type shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.11
6.03.03.05.05
The flat top repeatability type shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.12
6.03.03.05.05
The uniformity of the flattop type shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.13
6.03.03.05.05
The deflecting Angle type shall be 30 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.14
6.03.03.05.05
The rep rate spec type shall be TBD (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.15
6.03.03.05.05
The output voltage Spec type shall be 80 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.17
6.03.03.05.05
The inductance with cable type shall be 40 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.16
6.03.03.05.05
The output current spec type shall be 1200 0
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-EXT_PULSE_SEPT.18
6.03.03.05.05
The cooling type type shall be water
05/16/2025
In Process
FALSE

EIS-RCS-CONT : EIS RCS Controls (WBS 6.07.02)

EIS-RCS-CONT EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

EIS-RCS-CONT-INJ : EIS RCS Controls System Injection Tuning (WBS 6.07.02)

EIS-RCS-RF : EIS RCS RF System (WBS 6.08)

EIS-RCS-RF-ACAV:591M

P-EIS-RCS-RF-ACAV:591M.01
6.08.04.02
The SRF CM shall be outfitted with flow control, thermometry, pressure, and RF instrumentation as to monitor and control all sub-systems during the cooldown, warm-up, operation and testing.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.02
6.08.04.02
The cavity helium bath maximum operational temperature shall be 2 K.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.03
6.08.04.02
The cavity helium bath maximum operational pressure shall be 30 mbar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.04
6.08.04.02
The cavity helium bath operation pressure stability shall be ± 0.1 mbar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.05
6.08.04.02
The maximum helium supply operational temperature shall be 5.5 K.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.06
6.08.04.02
The range of the helium supply operational pressure shall be 3 to 3.5 bar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.07
6.08.04.02
The range of the combined helium return temperature shall be 64 to 66 K.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.08
6.08.04.02
The range of the combined helium return pressure shall be 2.4 to 2.6 bar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.09
6.08.04.02
The maximum sub-atmospheric helium return temperature shall be 4.5 K.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.10
6.08.04.02
The maximum sub-atmospheric helium return pressure shall be 30 mbar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.11
6.08.04.02
The minimum cooldown rate of the SRF cavity between 300K to 150K shall be 10 K/hour.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.12
6.08.04.02
The minimum cooldown rate of the SRF cavity between 150K to 50K shall be 30 K/hour.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.13
6.08.04.02
The minimum cooldown rate of the SRF cavity between 50K to 4.5K shall be 10 K/hour.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.14
6.08.04.02
The minimum cooldown rate of the SRF cavity between 4.5K to 2K shall be 0.5 K/hour.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.15
6.08.04.02
The minimum cooldown rate of the SRF cavity between 4.5K to 2K shall be 30 K/hour.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.16
6.08.04.02
The maximum thermal radiative heat transfer to all 2K and 5K surfaces shall be 2 W/cm^2.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.17
6.08.04.02
The maximum thermal radiative heat transfer to all 50K surfaces shall be 2 W/m^2.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.18
6.08.04.02
The SRF CM shall achieve steady state temperature with the cavity bath at 4K in a maximum of 2 days.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.19
6.08.04.02
The chilled water and low-conductivity water operational temperature range shall be 295 to 315 K.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.20
6.08.04.02
The chilled water and low-conductivity water operational pressure range shall be 7.5 to 8.5 bar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.21
6.08.04.02
The minimum magnetic shield attenuation factor at SRF cavity equator shall be 70.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.22
6.08.04.02
The SRF cryomodule maximum design ambient magnetic field amplitude shall be 700 mG.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.23
6.08.04.02
The SRF CM shall operate through a minimum of 200 thermal cycles.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.24
6.08.04.02
The minimum SRF CM Slow Tuner 1% range tuning cycles shall be 100000 cycles.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.25
6.08.04.02
The minimum SRF CM Slow Tuner full range tuning cycles shall be 1000 cycles.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.26
6.08.04.02
The manufactured SRF CM Cavity shall produce no field emission at 20 MV.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.27
6.08.04.02
The SRF CM components that cannot be maintained in-situ shall be designed with a minimum lifetime radiation tolerance of 1000 kGy.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.28
6.08.04.02
The SRF CM components that can be maintained in-situ shall have an annual minimum radiation tolerance of 1 kGy.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.29
6.08.04.02
The active SRF cavity tuning mechanism components (bearings/motor/piezo) shall be replaceable and maintainable in-situ.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.30
6.08.04.02
The SRF Cavity Fast Tuner shall have a minimum lifetime of 1 year between maintenance cycles.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.31
6.08.04.02
All critical monitoring and control instruments that cannot be maintained in-situ shall utilize a back-up instrument.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.32
6.08.04.02
The total SRF maximum RF longitudinal impedance (accelerator definition) shall be TBD MΩ Ghz.
05/16/2025
In Process
FALSE

P-EIS-RCS-RF-ACAV:591M.33
6.08.04.02
The total SRF maximum RF horizontal impedance (accelerator definition) shall be TBD MΩ/m.
05/16/2025
In Process
FALSE

P-EIS-RCS-RF-ACAV:591M.34
6.08.04.02
The total SRF maximum RF vertical impedance (accelerator definition) shall be TBD MΩ/m.
05/16/2025
In Process
FALSE

P-EIS-RCS-RF-ACAV:591M.35
6.08.04.02
The minimum cavity aperture radius shall be (TBD 90) mm.
05/16/2025
In Process
FALSE

P-EIS-RCS-RF-ACAV:591M.36
6.08.04.02
The maximum broadband RF power emitted from the CM via the beampipes shall be 5 kW.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.37
6.08.04.02
The Maximum Dipole multipole content shall be TBD mT-m.
05/16/2025
In Process
FALSE

P-EIS-RCS-RF-ACAV:591M.38
6.08.04.02
The Maximum Quadrupole multipole content shall be TBD mT.
05/16/2025
In Process
FALSE

P-EIS-RCS-RF-ACAV:591M.39
6.08.04.02
The Maximum Sextuple multipole content shall be TBD T/m.
05/16/2025
In Process
FALSE

P-EIS-RCS-RF-ACAV:591M.40
6.08.04.02
The Maximum Octupole multipole content shall be TBD mT/m^2.
05/16/2025
In Process
FALSE

P-EIS-RCS-RF-ACAV:591M.41
6.08.04.02
The SRF cavity minimum manufactured quality factor (Q0) at the operating voltage shall be 2e10.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.42
6.08.04.02
The SRF cavity minimum manufactured operating voltage shall be 17 MV.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.43
6.08.04.02
The SRF cavity loaded Quality Factor (Q_loaded) shall be TBD (1.0±0.5e6).
05/16/2025
In Process
FALSE

P-EIS-RCS-RF-ACAV:591M.44
6.08.04.02
The SRF cavity field probe Qext range shall be 1.00E11 to 2.00E11.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.45
6.08.04.02
The SRF cavity nominal cold frequency shall be 591.039 MHz.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.46
6.08.04.02
The SRF pressure sensitivity maximum shall be 5 Hz/mbar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.47
6.08.04.02
The SRF maximum lorentz force detuning shall be 1 Hz/(MV/m)^2.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.48
6.08.04.02
The SRF cavity maximum Niobium temperature at all flanges and full power operation shall be 5 K.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.49
6.08.04.02
The warm beamline maximum vacuum shall be 5.0e-7 mbar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.50
6.08.04.02
The cold beamline maximum vacuum shall be 1.0e-9 mbar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.51
6.08.04.02
The beamline vacuum maximum leak rate shall be 5e-10 mbar L/s.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.52
6.08.04.02
The warm insulating maximum vacuum shall be 1.0e-5 mbar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.53
6.08.04.02
The cold insulating maximum vacuum shall be 5.0e-7 mbar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.54
6.08.04.02
The insulating vacuum maximum leak rate shall be 1.0e-8 mbar L/s.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.55
6.08.04.02
The minimum SRF Cavity Fast Tuner tuning range shall be 400 Hz.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.56
6.08.04.02
The minimum SRF Cavity Fast Tuner tuning rate shall be 10000 Hz/s.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.57
6.08.04.02
The minimum SRF Cavity Fast Tuner resolution shall be ±1 Hz.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.58
6.08.04.02
The maximum SRF Cavity Fast Tuner hysteresis shall be ±1 Hz.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.59
6.08.04.02
The minimum SRF Cavity Slow Tuner tuning range shall be 600 kHz.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.60
6.08.04.02
The minimum SRF Cavity slow tuner tuning rate shall be 800 Hz/s.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.61
6.08.04.02
The maximum SRF Cavity Slow Tuner resolution shall be ±1 Hz.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.62
6.08.04.02
The maximum SRF Cavity Slow Tuner hysteresis shall be ±10 Hz.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.63
6.08.04.02
The external warm maximum allowable working pressure of the SRF cavity shall be 2.2 bar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.64
6.08.04.02
The external cold maximum allowable working pressure of the SRF cavity shall be 5.2 bar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.65
6.08.04.02
The internal maximum allowable working pressure of the SRF cavity shall be 1.8 bar.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.66
6.08.04.02
All cryomodule surfaces accessible to workers shall be within the temperature range of 283 to 333 K.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.67
6.08.04.02
The SRF CM shall be designed and manufactured to meet all applicable standards,as directed by the EIC Code of Record and/or all applicable excluded items governed by the EIC Memorandum of Agreements (MOA), and defined by ASME B31.3.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.68
6.08.04.02
The SRF CM shall be designed and manufactured to meet all applicable standards,as directed by the EIC Code of Record and/or all applicable excluded items governed by the EIC Memorandum of Agreements (MOA), and defined by ASME BPVC.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.69
6.08.04.02
The SRF CM shall be designed and manufactured to meet all applicable standards,as directed by the EIC Code of Record and/or all applicable excluded items governed by the EIC Memorandum of Agreements (MOA), and defined by ASTM C1055.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.70
6.08.04.02
The SRF CM shall be designed and manufactured to meet all applicable standards,as directed by the EIC Code of Record and/or all applicable excluded items governed by the EIC Memorandum of Agreements (MOA), and defined by NFPA 70.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.71
6.08.04.02
The SRF CM shall be designed and manufactured to meet all applicable standards,as directed by the EIC Code of Record and/or all applicable excluded items governed by the EIC Memorandum of Agreements (MOA), and defined by NFPA 70E.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.72
6.08.04.02
The SRF CM shall be designed and manufactured as directed by the JLAB ES&H Manual to meet all applicable safety standards as defined by API 520 & API 521.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.73
6.08.04.02
The SRF CM shall be designed and manufactured as directed by the JLAB ES&H Manual to meet all applicable safety standards as defined by CGA S1.3.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.74
6.08.04.02
The SRF CM shall be designed and manufactured as directed by the JLAB ES&H Manual to meet all applicable safety standards as defined by AWS.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.75
6.08.04.02
The SRF CM maximum length shall be 5.2 m.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.76
6.08.04.02
The SRF CM maximum width shall be 2.15 m.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.77
6.08.04.02
The SRF CM maximum height shall be 1.7 m.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.78
6.08.04.02
The distance from the beamline to the tunnel floor shall be TBD ± 20 mm.
05/16/2025
In Process
FALSE

P-EIS-RCS-RF-ACAV:591M.79
6.08.04.02
TheSRF Cryomodule Cavity Electromagnetic Center Alignment Tolerance in X shall be ±250 μm.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.80
6.08.04.02
TheSRF Cryomodule Cavity Electromagnetic Center Alignment Tolerance in Y shall be ±250 μm.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.81
6.08.04.02
TheSRF Cryomodule Cavity Electromagnetic Center Alignment Tolerance in Z shall be ±5 mm.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.82
6.08.04.02
TheSRF Cryomodule Cavity Electromagnetic Center Alignment Tolerance for the roll shall be ±0.04 radians.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.83
6.08.04.02
TheSRF Cryomodule Cavity Electromagnetic Center Alignment Tolerance for the pitch shall be ±0.01 radians.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.84
6.08.04.02
TheSRF Cryomodule Cavity Electromagnetic Center Alignment Tolerance for the yaw shall be ±0.01 radians.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.85
6.08.04.02
Conditioning for individual cavities shall have a maximum average 2.0 K cryogenic power dissipation of 250 W.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.86
6.08.04.02
Conditioning for individual cavities shall be achieved with a maximum helium bath temperature of 2.1 K.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.87
6.08.04.02
The SRF CM shall be capable of withstanding a maximum allowable vertical acceleration of ±4 G.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.88
6.08.04.02
The SRF CM shall be capable of withstanding a maximum allowable lateral acceleration of ±1.5 G.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.89
6.08.04.02
The SRF CM shall be capable of withstanding a maximum allowable beamline axis acceleration of ±5 G.
05/16/2025
Approved
FALSE

P-EIS-RCS-RF-ACAV:591M.90
6.08.04.02
The SRF CM shall be designed to withstand a tilt around the beamline axis (roll) up to ±0.7 radians.
05/16/2025
Approved
FALSE

EIS-HETL : EIS High Energy Transfer Line (HETL) System (WBS 6.03.03)

EIS-HETL-MAG : EIS HETL Magnet (WBS 6.03.03.01)

EIS-HETL-MAG-B1 : EIS HETL Magnet B1 (WBS 6.03.03.01)

EIS-HETL-MAG-B2 : EIS HETL Magnet B2 (WBS 6.03.03.01)

EIS-HETL-MAG-D1 : EIS HETL Magnet D1 (WBS 6.03.03.01)

EIS-HETL-MAG-D1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

EIS-HETL-MAG-D2 : EIS HETL Magnet D2 (WBS 6.03.03.01)

EIS-HETL-MAG-D2 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-HETL-MAG-D3 : EIS HETL Magnet D3 (WBS 6.03.03.01)

EIS-HETL-MAG-D3 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-HETL-MAG-INDSEPT1 : EIS HETL Magnet INDSEPT1 (WBS 6.03.03.01)

EIS-HETL-MAG-INDSEPT1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-HETL-MAG-KH1 : EIS HETL Magnet KH1 (WBS 6.03.03.01)

EIS-HETL-MAG-KH1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-HETL-MAG-KV1 : EIS HETL Magnet KV1 (WBS 6.03.03.01)

EIS-HETL-MAG-KV1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-HETL-MAG-Q1 : EIS HETL Magnet Q1 (WBS 6.03.03.01)

EIS-HETL-MAG-Q1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-HETL-MAG-Q2 : EIS HETL Magnet Q2 (WBS 6.03.03.01)

EIS-HETL-MAG-SEPT1 : EIS HETL Magnet SEPT1 (WBS 6.03.03.01)

EIS-HETL-MAG-SEPT1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

EIS-HETL-MAG-SEPT2 : EIS HETL Magnet SEPT2 (WBS 6.03.03.01)

EIS-HETL-MAG-SEPT2 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

EIS-HETL-MAG-ESR_INJ_BMP : EIS HETL Injection Bump ESR Magnet (WBS 6.03.03.05.08)

EIS-HETL-MAG-BUMP : High Energy Transfer Line Bump Magnet

EIS-HETL-MAG-SEPT : High Energy Transfer Line Septum Magnets

EIS-HETL-PS : EIS HETL Magnet Power Supply (WBS 6.03.03.02)

EIS-HETL-PS-B1 : EIS HETL Magnet Power Supply B1 (WBS 6.03.03.02)

EIS-HETL-PS-B2 : EIS HETL Magnet Power Supply B2 (WBS 6.03.03.02)

EIS-HETL-PS-D1 : EIS HETL Magnet Power Supply D1 (WBS 6.03.03.02)

EIS-HETL-PS-D1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-HETL-PS-D2 : EIS HETL Magnet Power Supply D2 (WBS 6.03.03.02)

EIS-HETL-PS-D2 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-HETL-PS-D3 : EIS HETL Magnet Power Supply D3 (WBS 6.03.03.02)

EIS-HETL-PS-D3 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-HETL-PS-INDSEPT1 : EIS HETL Magnet Power Supply INDSEPT1 (WBS 6.03.03.02)

EIS-HETL-PS-INDSEPT1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-HETL-PS-KH1 : EIS HETL Magnet Power Supply KH1 (WBS 6.03.03.02)

EIS-HETL-PS-KH1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-HETL-PS-KV1 : EIS HETL Magnet Power Supply KV1 (WBS 6.03.03.02)

EIS-HETL-PS-KV1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-HETL-PS-Q1 : EIS HETL Magnet Power Supply Q1 (WBS 6.03.03.02)

EIS-HETL-PS-Q1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-HETL-PS-Q2 : EIS HETL Magnet Power Supply Q2 (WBS 6.03.03.02)

EIS-HETL-PS-SEPT1 : EIS HETL Magnet Power Supply SEPT1 (WBS 6.03.03.02)

EIS-HETL-PS-SEPT1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-HETL-PS-SEPT2 : EIS HETL Magnet Power Supply SEPT2 (WBS 6.03.03.02)

EIS-HETL-PS-SEPT2 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-HETL-PS-ESR_INJ_BMP : EIS HETL Injection Bump ESR Power Supply (WBS 6.03.03.05)

EIS-HETL-PS-ESR_INJ_BMP EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-HETL-VAC : EIS HETL Vacuum (WBS 6.03.03.03)

EIS-HETL-INST : EIS HETL Instrumentation System (WBS 6.03.03.04)

EIS-HETL-INST-BPM : EIS HETL Instrumentation Beam Profile Monitor (WBS 6.03.03.04)

EIS-HETL-INST-BPM EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-HETL-INST-BPM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed Beam Position Monitors at the quadrupoles and at the entry and exit of a number of the dipoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

EIS-HETL-INST-BPM-ELEC : EIS HETL Instrumentation Beam Profile Monitor Electronic (WBS 6.03.03.04.01)

EIS-HETL-INST-BPM-PU : EIS HETL Instrumentation Beam Profile Monitor Pick-Up (WBS 6.03.03.04.01)

EIS-HETL-INST-CM : EIS HETL Instrumentation Charge Monitor (WBS 6.03.03.04)

EIS-HETL-INST-PM : EIS HETL Instrumentation Profile Monitor (WBS 6.03.03.04)

EIS-HETL-INST-PM EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-HETL-INST-PM.1
6.03.03
For instrumentation purposes the high energy TL from the RCS to the ESR shall contain a number of strategically placed YAG\OTR at the entry and exit of a number of the diploes and quadrupoles as required.
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

EIS-HETL-INST-IC : High Energy Transfer Line Integrating Current Monitor

EIS-HETL-INST-POL : High Energy Transfer Line Polarization Measurement System

EIS-HETL-ESR : High Energy Transfer Line ESR

EIS-HETL-ESR-INJ : High Energy Transfer Line ESR Injection Section

EIS-HETL-SLINE : High Energy Transfer Stripline

EIS-HETL-SLINE-FKICK : High Energy Transfer Fast Stripline Kicker

EIS-METL : EIS Medium Energy Transfer Line (METL) (WBS 6.03.03)

EIS-METL-MAG : EIS METL Magnet (WBS 6.03.03.01)

EIS-METL-MAG-BMP1 : EIS METL Magnet BMP1 (WBS 6.03.03.01)

EIS-METL-MAG-DH1 : EIS METL Magnet DH1 (WBS 6.03.03.01)

EIS-METL-MAG-DH1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-METL-MAG-DH2 : EIS METL Magnet DH2 (WBS 6.03.03.01)

EIS-METL-MAG-DH2 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-METL-MAG-DH3 : EIS METL Magnet DH3 (WBS 6.03.03.01)

EIS-METL-MAG-DH3 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-METL-MAG-DV1 : EIS METL Magnet DV1 (WBS 6.03.03.01)

EIS-METL-MAG-DV1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-METL-MAG-KH1 : EIS METL Magnet KH1 (WBS 6.03.03.01)

EIS-METL-MAG-KH1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-METL-MAG-KV1 : EIS METL Magnet KV1 (WBS 6.03.03.01)

EIS-METL-MAG-KV1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-METL-MAG-Q1 : EIS METL Magnet Q1 (WBS 6.03.03.01)

EIS-METL-MAG-Q1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-METL-MAG-Q_BATES : EIS METL Magnet BATES (WBS 6.03.03.01)

EIS-METL-MAG-Q_BATES EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-METL-MAG-SEPTUM : EIS METL Magnet SEP1 (WBS 6.03.03.01)

EIS-METL-MAG-SEPTUM EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-METL-MAG-SPINSOL : EIS METL Magnet SOL1 (WBS 6.03.03.01)

EIS-METL-MAG-SPINSOL EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-METL-MAG-SPINSOL.4
6.03.03
The spin rotator entry quadrupole shall have at least 2 families this is needed to control the electron beam optics as required.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.5
6.03.03
The spin rotator quadrupoles after the Spin rotator solenoid shall be able to match the beam beta functions βx and βy to that required for entry into the 400MeV transfer line.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.6
6.03.03
The spin rotator exit quadrupoles shall have at least 2 families this is required to control the electron beam optics as needed.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.7
6.03.03
The spin rotator solenoid shall rotate the electron beam spin from the X axis to the vertical y-axis before it enters the medium [400MeV] transport line to the RCS.
05/16/2025
Not Applicable
FALSE

F-EIS-METL-MAG-SPINSOL.8
6.03.03
The spin rotator solenoid shall have an integrated gradient of 2.2 [T.m] required to rotate the spin from the horizontal axis to the vertical axis.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

EIS-METL-MAG-DIP : Medium Energy Transfer Line Dipole Magnet

EIS-METL-MAG-QUAD : Medium Energy Transfer Line Quadrupole Magnet

EIS-METL-PS : EIS METL Magnet Power Supply (WBS 6.03.03.02)

EIS-METL-PS-BMP1 : EIS METL Magnet Power Supply BMP1 (WBS 6.03.03.02)

EIS-METL-PS-DH1 : EIS METL Magnet Power Supply DH1 (WBS 6.03.03.02)

EIS-METL-PS-DH1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-METL-PS-DH2 : EIS METL Magnet Power Supply DH2 (WBS 6.03.03.02)

EIS-METL-PS-DH2 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-METL-PS-DH3 : EIS METL Magnet Power Supply DH3 (WBS 6.03.03.02)

EIS-METL-PS-DH3 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-METL-PS-DV1 : EIS METL Magnet Power Supply DV1 (WBS 6.03.03.02)

EIS-METL-PS-DV1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-METL-PS-KH1 : EIS METL Magnet Power Supply KH1 (WBS 6.03.03.02)

EIS-METL-PS-KH1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-METL-PS-KV1 : EIS METL Magnet Power Supply KV1 (WBS 6.03.03.02)

EIS-METL-PS-KV1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-METL-PS-Q1 : EIS METL Magnet Power Supply Q1 (WBS 6.03.03.02)

EIS-METL-PS-Q1 EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-METL-PS-Q2 : EIS METL Magnet Power Supply Q2 (WBS 6.03.03.02)

EIS-METL-PS-Q3 : EIS METL Magnet Power Supply Q3 (WBS 6.03.03.02)

EIS-METL-PS-Q4 : EIS METL Magnet Power Supply Q4 (WBS 6.03.03.02)

EIS-METL-PS-Q_BATES : EIS METL Magnet Power Supply BATES (WBS 6.03.03.02)

EIS-METL-PS-Q_BATES EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-METL-PS-SEPTUM : EIS METL Magnet Power Supply SEP1 (WBS 6.03.03.02)

EIS-METL-PS-SEPTUM EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-METL-PS-SPINSOL : EIS METL Magnet Power Supply SOL1 (WBS 6.03.03.02)

EIS-METL-PS-SPINSOL EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

EIS-METL-VAC : EIS METL Vacuum (WBS 6.03.03.03)

EIS-METL-INST : EIS METL Instrumentation (WBS 6.03.03.04)

EIS-METL-INST EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-METL-INST.1
6.03.03
To measure and control the beam in the medium energy 400 MeV transfer line there shall be sufficient beam position monitors for orbit control, transverse profile monitors, and bunch charge monitors as required.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

EIS-METL-INST-BPM : EIS METL Instrumentation Beam Profile Monitor (WBS 6.03.03.04)

EIS-METL-INST-BPM EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-METL-INST-BPM.1
6.03.03
To control the beam through the Spin Rotator section there shall be a Beam Position Monitors placed throughout the spin rotator as required.
05/16/2025
Not Applicable
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

EIS-METL-INST-BPM-ELEC : EIS METL Instrumentation Beam Profile Monitor Electronic (WBS 6.03.03.04.01)

EIS-METL-INST-BPM-PU : EIS METL Instrumentation Beam Profile Monitor Pick-Up (WBS 6.03.03.04.01)

EIS-METL-INST-CM : EIS METL Instrumentation Charge Monitor (WBS 6.03.03.04)

EIS-METL-INST-PM : EIS METL Instrumentation Profile Monitor (WBS 6.03.03.04)

EIS-METL-INJ : Medium Energy Transfer Line Electron Injector Injection Section

EIS-METL-INJ-MAG : Medium Energy Transfer Line Electron Injector Injection Section Magnet

EIS-METL-INJ-MAG-FKICK : Medium Energy Transfer Line Electron Injector Injection Section Fast Kicker Magnet

EIS-METL-INJ-MAG-SEP : Medium Energy Transfer Line Electron Injector Injection Section Septum Magnet

EIS-METL-RCS : Medium Energy Transfer Line RCS

EIS-METL-RCS-INJ : Medium Energy Transfer Line RCS Injection Section

EIS-METL-RCS-INJ-MAG : Medium Energy Transfer Line RCS Injection Section Magnet

EIS-METL-RCS-INJ-MAG-BUMP : Medium Energy Transfer Line RCS Injection Section Bump Magnet

EIS-METL-RF : Medium Energy Transfer Line RF

EIS-METL-RF-FKICK : Medium Energy Transfer Line Fast RF Kicker

EIS-GUN : EIS Electron Source Gun (WBS 6.03.04.01)

F-EIS-GUN.8x
6.03.04
Need Gun Vaccum parent requirement? The gun vacuumn shall reach UHV standards?
05/16/2025
Not Applicable
FALSE

P-EIS-GUN.01
6.03.04.01
The Bunch Energy shall be 280 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN.02
6.03.04.01
The Bunch to Bunch Energy Variation shall be 1.5e-3 dE/E, rms
05/16/2025
On Hold
FALSE

P-EIS-GUN.03
6.03.04.01
The Bunch to Bunch Phase Variation shall be 5 ps, rms
05/16/2025
On Hold
FALSE

P-EIS-GUN.04
6.03.04.01
The Slow Energy Drift (T > 60s) shall be 1E-3 dE/E, rms
05/16/2025
On Hold
FALSE

P-EIS-GUN.05
6.03.04.01
The Slow Phase Drift (T > 60s) shall be 10 ps, rms
05/16/2025
On Hold
FALSE

P-EIS-GUN.06
6.03.04.01
The Bunch Charge (Min) shall be 0.1 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN.07
6.03.04.01
The Bunch Charge (Max) shall be 8 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN.08
6.03.04.01
The Polarization shall be Up to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN.09
6.03.04.01
The Polarization Orientation shall be Longitudinal
05/16/2025
On Hold
FALSE

P-EIS-GUN.10
6.03.04.01
The Bunch Length shall be 1.2-1.6 ns, rms
05/16/2025
On Hold
FALSE

P-EIS-GUN.11
6.03.04.01
The Bunch Energy Spread shall be 8e-3 dE/E, rms
05/16/2025
On Hold
FALSE

P-EIS-GUN.12
6.03.04.01
The Bunch Normalized Horizontal Emittance shall be 8 mm-mrad, rms
05/16/2025
On Hold
FALSE

P-EIS-GUN.13
6.03.04.01
The Bunch Normalized Horizontal Emittance Tolerance shall be +/-1 %
05/16/2025
On Hold
FALSE

P-EIS-GUN.14
6.03.04.01
The Bunch Normalized Vertical Emittance shall be 7 mm-mrad, rms
05/16/2025
On Hold
FALSE

P-EIS-GUN.15
6.03.04.01
The Bunch Normalized Vertical Emittance Tolerance shall be +/-1 %
05/16/2025
On Hold
FALSE

P-EIS-GUN.16
6.03.04.01
The Bunch Longitudinal Profile Distribution shall be Beer Can
05/16/2025
On Hold
FALSE

EIS-GUN EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-GUN.1x
6.03.04
A compact Mott Polarimeter shall be used to inspect the polarization level and Quantum efficiency of the super lattice GaAs cathode, this system is not part of the gun chamber.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.3x
6.03.03
The low energy transfer line shall have an additional branch between the Gun and the Bunching section which can transfer individual electron bunches into the diagnostic beamline section.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.4x
6.03.03
The low energy transfer line shall have a laser port between the Gun and the Bunching section which will allow an optical path for the laser to illuminate the cathode face of the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-GUN.6x
6.03.04
The gun shall have steering coils to direct the liberated electrons (These can be reused from the existing Gun system.)
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

EIS-GUN-TIMING : EIS Electron Source Gun Timing (WBS 6.03.04.01)

EIS-GUN-VAC : EIS Electron Source Gun Vacuum (WBS 6.03.04.01.02)

EIS-GUN-ESOURCE : EIS Electron Source Gun Electron Beam (WBS 6.03.04.02)

EIS-GUN-ESOURCE EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

EIS-GUN-LASER : EIS Electron Source Gun Laser (WBS 6.03.04.02)

EIS-GUN-LASER EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

EIS-GUN-INST : EIS Electron Source Gun Instrumentation (WBS 6.03.04.02.06)

EIS-GUN-INST EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-GUN-INST.4
6.03.04
To characterize and control the fresh bunches sent to the Mott polarimeter, the gun diagnostic beamline shall contain instrumentation to measure and control the profile, position, and charge of the beam.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-INST.5
6.03.04
The Diagnostic beamline section shall have one Beam Profile Monitor and Wien Filter and an electrostatic bender before the Mott polarimeter and Faraday Cup.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-GUN-INST.6
6.03.04
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
Not Applicable
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

EIS-GUN-INST-EM : EIS Electron Source Gun Instrumentation Emittance Monitor (WBS 6.03.04.02.06)

EIS-GUN-INST-F_Cup : EIS Electron Source Gun Instrumentation Faraday Cup (WBS 6.03.04.02.06)

EIS-GUN-INST-MOT : EIS Electron Source Gun Instrumentation Mott Polarimeter (WBS 6.03.04.02.06)

EIS-GUN-INST-MOT EXTERNALS
Requirements who's parents are in other sub-systems.

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

EIS-GUN-INST-SR : EIS Electron Source Gun Instrumentation Spin Rotator (WBS 6.03.04.02.06)

EIS-GUN-CONT : EIS Electron Source Gun Controls System (WBS 6.07.02)

EIS-GUN-MAG : Gun Diagnostic Line Magnet

EIS-GUN-MAG EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-GUN-MAG.1
6.03.04
Following the DC gun, the electron bunch shall be deflected through a bending dipole into the Bunching section
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.2
6.03.04
2 solenoids shall be placed between the gun and the bending dipole into the bunching section capable of correcting the beam position.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.3
6.03.04
Provision shall be made for an appropriate number of air cored steering coils between the Gun and bunching section to correct the electron beam position as required.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.4
6.03.04
A bending dipole shall follow the Gun and be able to bend the beam from the gun into the bunching section OR bend separate electron bunches into the separate diagnostic beam line.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.5
6.03.04
The bending dipole after the gun shall also have the capability to deflect the beam enough to allow a laser to illuminate the photocathode head on.
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.6
6.03.04
A minimum of three solenoids shall be placed between the gun and the first bunching cavity to maintain the beam size for 5–10 nC bunches
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.7
6.03.04
Short air core trim coils shall be used to correct beam position for energies greater than 100 keV
05/16/2025
Not Applicable
FALSE

F-EIS-GUN-MAG.8
6.03.04
The Diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter
05/16/2025
Not Applicable
FALSE

EIS-LINAC : EIS Electron Source LINAC (WBS 6.03.04.01)

P-EIS-LINAC.01
6.03.04.01
The Bunch Energy shall be 400 MeV
05/16/2025
On Hold
FALSE

P-EIS-LINAC.02
6.03.04.01
The Bunch to Bunch Energy Variation shall be 1.5e-3 dE/E, rms
05/16/2025
On Hold
FALSE

P-EIS-LINAC.03
6.03.04.01
The Bunch to Bunch Phase Variation shall be 8 ps, rms
05/16/2025
On Hold
FALSE

P-EIS-LINAC.04
6.03.04.01
The Slow Energy Drift (T > 60s) shall be 1E-3 dE/E, rms
05/16/2025
On Hold
FALSE

P-EIS-LINAC.05
6.03.04.01
The Slow Phase Drift (T > 60s) shall be 8 ps, rms
05/16/2025
On Hold
FALSE

P-EIS-LINAC.06
6.03.04.01
The Bunch Charge (Min) shall be 0.1 nC
05/16/2025
On Hold
FALSE

P-EIS-LINAC.07
6.03.04.01
The Bunch Charge (Max) shall be 8 nC
05/16/2025
On Hold
FALSE

P-EIS-LINAC.08
6.03.04.01
The Polarization shall be Up to 90 %
05/16/2025
On Hold
FALSE

P-EIS-LINAC.09
6.03.04.01
The Polarization Orientation shall be Longitudinal
05/16/2025
On Hold
FALSE

P-EIS-LINAC.10
6.03.04.01
The Bunch Length shall be 40 ps, rms
05/16/2025
On Hold
FALSE

P-EIS-LINAC.11
6.03.04.01
The Bunch Energy Spread shall be 2.5e-3 dE/E, rms
05/16/2025
On Hold
FALSE

P-EIS-LINAC.12
6.03.04.01
The Bunch Normalized Horizontal Emittance shall be 40 mm-mrad, rms
05/16/2025
On Hold
FALSE

P-EIS-LINAC.13
6.03.04.01
The Bunch Normalized Horizontal Emittance Tolerance shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-LINAC.14
6.03.04.01
The Bunch Normalized Vertical Emittance shall be 40 mm-mrad, rms
05/16/2025
On Hold
FALSE

P-EIS-LINAC.15
6.03.04.01
The Bunch Normalized Vertical Emittance Tolerance shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-LINAC.16
6.03.04.01
The Beam Loss from U.I.P to D.I.P (Maximum) shall be 5 %
05/16/2025
On Hold
FALSE

EIS-LINAC EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-LINAC.4
6.03.04
The 1st part of the S-band LINAC shall be contained inside a continuous solenoidal field to maintain the bunch envelope into the LINAC (see bunching section solenoid).
05/16/2025
Not Applicable
FALSE

EIS-LINAC-ACCEL : EIS Electron Source LINAC Accelerating System (WBS 6.03.04.01)

EIS-LINAC-BEAM : EIS Electron Source LINAC Beamline Electron Bunch (WBS 6.03.04.01)

EIS-LINAC-BUNCH_118MHZ : EIS Electron Source LINAC Buncher 118MHz (WBS 6.03.04.01)

EIS-LINAC-BUNCH_2856MHZ : EIS Electron Source LINAC Buncher 2856MHz (WBS 6.03.04.01)

EIS-LINAC-BUNCH_560MHZ : EIS Electron Source LINAC Buncher 560MHz (WBS 6.03.04.01)

EIS-LINAC-CONT : EIS Electron Source LINAC Controls (WBS 6.03.04.01)

EIS-LINAC-DECHIRP : EIS Electron Source LINAC De Chirp System (WBS 6.03.04.01)

EIS-LINAC-INST : EIS Electron Source LINAC Instrumentation (WBS 6.03.04.01)

EIS-LINAC-INST-BLM : EIS Electron Source LINAC Bunch Length Monitor (WBS 6.03.04.01)

EIS-LINAC-INST-BPM : EIS Electron Source LINAC Beam Position Monitor (WBS 6.03.04.01)

P-EIS-LINAC-INST-BPM.01
6.03.04.01.04.01
The BPM system shall provide bunch position measurements that meet the resolution requirements, over a bunch charge dynamic range of 0.1 to 10 nC
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-BPM.02
6.03.04.01.04.01
The BPM system single bunch position measurement resolution shall be less than or equal to 100 microns
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-BPM.03
6.03.04.01.04.01
Over a 24-hour period, the BPM pick-up housing mechanical position stability shall not vary by more than 100 microns
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-BPM.04
6.03.04.01.04.01
The BPM horizontal and vertical measurement range for round aperture BPM pick-ups, where the resolution requirements must be met, from the center of the beampipe shall be at least +/- 5 mm
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-BPM.05
6.03.04.01.04.01
The BPM horizontal and measurement range for the rectangular zigzag aperture BPM pick-ups, where the resolution requirements must be met, from the center of the beampipe shall be at least +/- 5 mm
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-BPM.06
6.03.04.01.04.01
The BPM vertical measurement range for the rectangular zigzag aperture BPM pick-ups, where the resolution requirements must be met, from the center of the beampipe shall be at least +/- 45 mm
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-BPM.07
6.03.04.01.04.01
The installation alignment difference between the BPM pick-up's mechanical center, and the mechanical center of a nearby quad magnet, or beam pipe center, shall be less than 100 microns
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-BPM.08
6.03.04.01.04.01
The maximum BPM position DAQ measurement rate shall be at least the maximum electron bunch or bunch pair rate of 300 Hz
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-BPM.09
6.03.04.01.04.01
The BPM system shall measure the position of every bunch, and graphically display the measurement data superimposed on a LINAC transport x,z and y,z diagram plots, through the Controls application with a refresh rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-BPM.10
6.03.04.01.04.01
Where the beampipe is rectangular in the zigzag, the arrangement of the BPM button locations shall be configured to meet the position measurement accuracy of better than 100 microns
05/16/2025
On Hold
FALSE

EIS-LINAC-INST-CM : EIS Electron Source LINAC Bunch Charge Monitors (ICT, WCM, FC) (WBS 6.03.04.01)

F-EIS-LINAC-INST-CM.2
6.03.04
To control the beam as it travels through the LINAC section there shall be a wire-scanner at the exit of all the accelerating cells as required.
05/16/2025
Not Applicable
FALSE

P-EIS-LINAC-INST-CM.01
6.03.04.01.04.02
The bunch charge dynamic range that the charge monitors shall measure is 0.1 to 10 nC
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-CM.02
6.03.04.01.04.02
The WCM charge measurement accuracy for a bunch charge range of 1-10 nC shall be at least 5 %
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-CM.03
6.03.04.01.04.02
The charge measurement accuracy for a bunch charge range of 100 pC to 1 nC shall be at least 10 %
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-CM.04
6.03.04.01.04.02
The maximum bunch charge measurement rate shall be the maximum rate of bunches, or bunch pairs through the LINAC 300 Hz
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-CM.05
6.03.04.01.04.02
Individual e-bunch charges, and short (<4 us long) bunch trains shall be measured using an ICT & BCM-IHR-E, with an accuracy of 1 %
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-CM.06
6.03.04.01.04.02
The remote-controlled pneumatically actuated Faraday Cup shall be able to measure a single bunch, or bunch train charges. When bunch charges are in the range of 6-10 nC, the measurement accuracy shall be better than 10 %
05/16/2025
On Hold
FALSE

EIS-LINAC-INST-CM EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-LINAC-INST-CM.1
6.03.04
Bunch charge measurements shall be performed at multiple locations through the LINAC.
05/16/2025
In Process
FALSE

EIS-LINAC-INST-PM : EIS Electron Source LINAC Transverse Profile Monitor (PM) (WBS 6.03.04.01)

P-EIS-LINAC-INST-PM.01
6.03.04.01.04.03
The transverse profile shall be measured using a screen material that is plunged into the path of the beam, screen type YAG:Ce
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-PM.02
6.03.04.01.04.03
The bunch charge range for measuring transverse profiles shall be 0.1 to 10 nC
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-PM.03
6.03.04.01.04.03
The H & V transverse image measurement range where the beam pipe has a 40 mm diameter, shall be at least +/- 10 mm
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-PM.04
6.03.04.01.04.03
The horizontal transverse image measurement range at the profile monitors in the zigzag rectangular aperture, shall be at least +/- 10 mm
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-PM.05
6.03.04.01.04.03
The vertical transverse image measurement range at the profile monitors in the zigzag rectangular apertures, shall be at least +/- 45 mm
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-PM.06
6.03.04.01.04.03
The expected horizontal and vertical transverse beam sizes at the profile monitors between the LINAC cavities is no larger than 2 mm rms
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-PM.07
6.03.04.01.04.03
The profile monitor station shall be equipped with a remote-control neutral density filter wheel that has 1 blank. The number of other positions with a variety of interchangeable different filters shall be 5
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-PM.08
6.03.04.01.04.03
The optical resolution for beam profile measurements using plunging YAG:Ce screens shall be less than 50 microns
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-PM.09
6.03.04.01.04.03
The installation alignment difference between the mechanical center of the YAG:Ce screen, and the mechanical center of a nearby quad magnet, or beam pipe center, shall be less than 100 microns
05/16/2025
On Hold
FALSE

P-EIS-LINAC-INST-PM.10
6.03.04.01.04.03
The H & V beam size measurement accuracy using plunging screens shall be better than 10 %
05/16/2025
On Hold
FALSE

EIS-LINAC-INST-PM EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-LINAC-INST-PM.1
6.03.04
To measure the beam profile in the LINAC section there shall be a plunging YAG/OTR transverse profile monitor between the 1st and 2nd accelerating cells.
05/16/2025
Not Applicable
FALSE

EIS-LINAC-VAC : EIS Electron Source LINAC Vacuum (WBS 6.03.04.01)

P-EIS-LINAC-VAC.01
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-LINAC-VAC.02
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius shall be greater than 0.4 within 16mm of beam center Gauss
05/16/2025
On Hold
FALSE

P-EIS-LINAC-VAC.03
6.03.04.01.02
The average vacuum level after conditioning shall be 1 x 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-LINAC-VAC.04
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr. TBD
05/16/2025
On Hold
FALSE

P-EIS-LINAC-VAC.05
6.03.04.01.02
The LINAC vacuum system shall be designed such that the average pressure through-out the majority of the accelerating structures, the Zigzag and De-chirp sections of the LINAC shall be less than 5 x 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-LINAC-VAC.06
6.03.04.01.02
The LINAC vacuum system beam tube aperture between and at either end of each accelerating structure shall have a nominal 40 mm (1 ½") diameter and all metal sealed Conflat flanges. 40 mm
05/16/2025
On Hold
FALSE

P-EIS-LINAC-VAC.07
6.03.04.01.02
The LINAC vacuum system average pressure in the bunching section and the first accelerating structure shall be maintained at less than 5 x 10^-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-LINAC-VAC.08
6.03.04.01.02
The LINAC vacuum system shall be designed to eliminate pressure bursts that may increase pressure in the BSA supplied polarized e-gun which are greater than 1 x 10^-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-LINAC-VAC.09
6.03.04.01.02
The LINAC vacuum system shall be designed so the pressure at the exit valve is less than 6.0 x 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-LINAC-VAC.10
6.03.04.01.02
The LINAC vacuum system waveguide RF vacuum pumps shall be sized to reliably achieve less than 2 x10^-9 Torr 2 x 10^-9 Torr
05/16/2025
On Hold
FALSE

P-EIS-LINAC-VAC.11
6.03.04.01.02
The LINAC vacuum system UHV outgassing rate of vacuum system components after UHV cleaning, vacuum heat treating (in the case of stainless steels-vacuum firing), and under vacuum for 100 hours shall not exceed 5 x 10^-12 Torr l/sec/cm2.
05/16/2025
On Hold
FALSE

EIS-LINAC-ZIGZAG : EIS Electron Source LINAC Zigzag (WBS 6.03.04.01)

EIS-LINAC-ZIGZAG-MAG : Zigzag Section Magnet

EIS-LINAC-ZIGZAG-MAG-CHIRP : Zigzag Section De-Chirp Cavity

EIS-LINAC-ZIGZAG-MAG-DIP : Zigzag Section Dipole Magnet

EIS-LINAC-ZIGZAG-MAG-QUAD : Zigzag Section Quadrupole Magnet

EIS-LINAC-BNCHR : Buncher Section

EIS-LINAC-BNCHR-INST : Buncher Section Instrumentation

EIS-LINAC-BNCHR-INST-BLM : Buncher Section Bunch Length Monitor

EIS-LINAC-BNCHR-INST-BPM : Buncher Section Beam Position Monitor

EIS-LINAC-BNCHR-INST-EM : Buncher Section Emittance Monitor

EIS-LINAC-BNCHR-INST-ICT : Buncher Section Integrating Current Transformer Monitor

EIS-LINAC-BNCHR-INST-LM : Buncher Section Beam Loss Monitor

EIS-LINAC-BNCHR-INST-TPM : Buncher Section Transverse Profile Monitor

EIS-LINAC-BNCHR-MAG : Buncher Section Magnet

EIS-LINAC-BNCHR-MAG-CORR : Buncher Section Corrector Magnet

EIS-LINAC-BNCHR-MAG-HELM : Buncher Section Helmholtz Magnet

EIS-LINAC-BNCHR-MAG-SOL : Buncher Section Solenoid Magnet

EIS-LINAC-BNCHR-RF : Buncher Section RF System

EIS-LINAC-BNCHR-VAC : Buncher Section Vacuum

EIS-LINAC-CAV : LINAC RF Cavity

EIS-LINAC-DUMP : LINAC Beam Dump

EIS-LINAC-DUMP-INST : LINAC Dump Line

EIS-LINAC-MAG : LINAC Magnet

EIS-LINAC-MAG-QUAD : LINAC Quadrupole Magnet

EIS-LINAC-MAG-WF : LINAC Window Frame Steering Magnet

EIS- PREINJ

EIS- PREINJ-BUNCH

EIS- PREINJ-BUNCH-MAG

EIS- PREINJ-BUNCH-MAG-HELM

EIS- PREINJ-LINAC

EIS- PREINJ-LINAC-CAV

EIS- PREINJ-LINAC-MAG

EIS- RCS

EIS- RCS-INST

EIS- RCS-INST EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS- RCS-INST.1
6.03.02
The instrumentation system shall contain a Beam Position Monitor system consisting of dual-plane Beam Position Monitors adjacent to each quadrupole.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.2
6.03.02
Select Beam Position Monitors in the injection region shall have turn-by-turn orbit measurement capability based on a single, remotely selectable bunch out of the fully filled bunch train to enable injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.3
6.03.02
The instrumentation system shall include a beam current monitor to measure average beam current.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.4
6.03.02
The instrumentation system shall include a system to measure individual bunch charges and bunch pattern.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.5
6.03.02
The instrumentation system shall include a system to measure transverse bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.6
6.03.02
The instrumentation system shall include a system to measure longitudinal bunch profiles.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.7
6.03.02
The instrumentation system shall contain a betatron and synchrotron tune monitors.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.8
6.03.02
The longitudinal bunch profile monitor needs turn-by-turn capability based on a single bunch in the fully filled bunch train to allow timing and energy adjustment for injection optimization.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

F-EIS- RCS-INST.9
6.03.02
The RCS shall contain a beam-based alignment system.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

F-EIS- RCS-INST.10
6.03.02
The RCS shall contain a beam loss monitor system at select regions.
05/16/2025
In Process
FALSE

EIS- RCS-LATTICE

EIS- RCS-LATTICE-ARC

F-EIS- RCS-LATTICE-ARC.1
6.03.02
The EIC RCS lattice arc magnet structure shall contain an array of 160 regular FODO cells to bend the beam and to control the beam optics broken into two arcs. The arc FODO cells shall consist of a horizontally focusing\defocusing quadrupole magnet followed by a correction dipole; then, followed a dipole bending magnet, and then followed by a sextupole correction magnet. With a drift space between these elements of > 0.1m long
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

EIS- RCS-LATTICE-STRAIGHT

F-EIS- RCS-LATTICE-STRAIGHT.1
6.03.02
The RCS will have two straight sections connecting the two arcs. Each straight shall be comprised of 2 FODO cells on each end for matching into the arcs and with one of the drifts long enough to accommodate extraction or injection and the necessary septa magnets. The straights shall also have 4 FODO cells in the center with enough space to accommodate 8 SRF cryo-modules to generate 130 MV of accelerating voltage.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

EIS- RCS-MAG

F-EIS- RCS-MAG.x2
6.03
The RCS quadrupole shall have 0.6 m long core with a peak k1 gradient of 0.785 m^-2. To control the magnet temperature during ramping it shall be water cooled. There shall be 352 quadrupoles needed for the RCS lattice.
08/20/2025
In Process
FALSE

F-EIS- RCS-MAG.x3
6.03
The RCS sextupole shall have a 0.2 m long core with a peak k2 gradient of 27.5 m^3. To control the magnet temperature during ramping it shall be water cooled. There shall be 320 sextupoles needed for the RCS lattice.
08/20/2025
In Process
FALSE

F-EIS- RCS-MAG.2
6.03
The magnets shall have the required field quality to meet the operational needs.
08/20/2025
In Process
FALSE

F-EIS- RCS-MAG.5
6.03.02
The good field region of the dipoles shall extend over a horizontal range of at least 15 mm in the radial direction, for all operational beam energies from 0.75 to 18Gev.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.12
6.03.02
The aperture of all magnets shall be large enough to accommodate the vacuum chamber.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.09
6.03.03.05.05
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.10
6.03.03.05.05
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.11
6.03.03.05.05
The magnets dipole field B shall be 1.512 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D1.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D1.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.09
6.03.03.01
The magnet length shall be <2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.10
6.03.03.01
The magnet slot length shall be 2.99 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.11
6.03.03.01
The magnets dipole field B shall be 0.193 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.09
6.03.03.01
The magnet length shall be <2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.10
6.03.03.01
The magnet slot length shall be 2 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.11
6.03.03.01
The magnets dipole field B shall be 0.525 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-D3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-D3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.01
6.03.03.05.08
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.02
6.03.03.05.08
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.03
6.03.03.05.08
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.4
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.5
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.06
6.03.03.05.08
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.07
6.03.03.05.08
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.08
6.03.03.05.08
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.09
6.03.03.05.08
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.10
6.03.03.05.08
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.11
6.03.03.05.08
The magnets dipole field B shall be 0.06 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.12
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.13
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.14
6.03.03.05.08
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.15
6.03.03.05.08
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.16
6.03.03.05.08
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.17
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.18
6.03.03.05.08
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.19
6.03.03.05.08
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.20
6.03.03.05.08
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.21
6.03.03.05.08
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.22
6.03.03.05.08
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.23
6.03.03.05.08
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.24
6.03.03.05.08
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.25
6.03.03.05.08
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.26
6.03.03.05.08
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.27
6.03.03.05.08
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.28
6.03.03.05.08
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.29
6.03.03.05.08
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.30
6.03.03.05.08
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.31
6.03.03.05.08
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.32
6.03.03.05.08
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.33
6.03.03.05.08
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.34
6.03.03.05.08
The magnet shall be designed to limit Xtalk Requirements N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.35
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.36
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.37
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.38
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.39
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.40
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.41
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.42
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.43
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.44
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.45
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.46
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.47
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.48
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.49
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.50
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.51
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.52
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.53
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.54
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.55
6.03.03.05.08
The magnet design shall constrain the ext. fringe field N (Yes or No)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-ESR_INJ_BMP.56
6.03.03.05.08
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.11
6.03.03.01
The magnets dipole field B shall be 1.051 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-INDSEPT1.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-INDSEPT1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.03
6.03.03.01
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.03
6.03.03.01
The field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.076 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 23.75 T/m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.15
6.03.03.01
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.16
6.03.03.01
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.17
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.01
6.03.03.05.03
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.02
6.03.03.05.03
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.03
6.03.03.05.03
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.4
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.5
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.06
6.03.03.05.03
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.07
6.03.03.05.03
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.08
6.03.03.05.03
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.09
6.03.03.05.03
The magnet length shall be <1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.10
6.03.03.05.03
The magnet slot length shall be 1.3 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.11
6.03.03.05.03
The magnets dipole field B shall be 0.924 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.12
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.13
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.14
6.03.03.05.03
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.15
6.03.03.05.03
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.16
6.03.03.05.03
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.17
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.18
6.03.03.05.03
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.19
6.03.03.05.03
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.20
6.03.03.05.03
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.21
6.03.03.05.03
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.22
6.03.03.05.03
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.23
6.03.03.05.03
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.24
6.03.03.05.03
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.25
6.03.03.05.03
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.26
6.03.03.05.03
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.27
6.03.03.05.03
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.28
6.03.03.05.03
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.29
6.03.03.05.03
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.30
6.03.03.05.03
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.31
6.03.03.05.03
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.32
6.03.03.05.03
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.33
6.03.03.05.03
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.34
6.03.03.05.03
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.35
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.36
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.37
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.38
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.39
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.40
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.41
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.42
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.43
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.44
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.45
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.46
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.47
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.48
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.49
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.50
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.51
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.52
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.53
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.54
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT1.55
6.03.03.05.03
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT1.56
6.03.03.05.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.01
6.03.03.05.05
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.02
6.03.03.05.05
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.03
6.03.03.05.05
The field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.4
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.5
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.06
6.03.03.05.05
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.07
6.03.03.05.05
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.08
6.03.03.05.05
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.09
6.03.03.05.05
The magnet length shall be <2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.10
6.03.03.05.05
The magnet slot length shall be 2.49 m
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.11
6.03.03.05.05
The magnets dipole field B shall be 0.82 T
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.12
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.13
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.14
6.03.03.05.05
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.15
6.03.03.05.05
The magnet harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.16
6.03.03.05.05
The magnet Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.17
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.18
6.03.03.05.05
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.19
6.03.03.05.05
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.20
6.03.03.05.05
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.21
6.03.03.05.05
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.22
6.03.03.05.05
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.23
6.03.03.05.05
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.24
6.03.03.05.05
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.25
6.03.03.05.05
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.26
6.03.03.05.05
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.27
6.03.03.05.05
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.28
6.03.03.05.05
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.29
6.03.03.05.05
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.30
6.03.03.05.05
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.31
6.03.03.05.05
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.32
6.03.03.05.05
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.33
6.03.03.05.05
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.34
6.03.03.05.05
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.35
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.36
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.37
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.38
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.39
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.40
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.41
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.42
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.43
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.44
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.45
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.46
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.47
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.48
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.49
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.50
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.51
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.52
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.53
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.54
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-MAG-SEPT2.55
6.03.03.05.05
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-HETL-MAG-SEPT2.56
6.03.03.05.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-D3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-D3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-ESR_INJ_BMP.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-INDSEPT1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-INDSEPT1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT1.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT1.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.01
6.03.03.05
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.02
6.03.03.05
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.03
6.03.03.05
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.04
6.03.03.05
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.5
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.06
6.03.03.05
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.07
6.03.03.05
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.08
6.03.03.05
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.09
6.03.03.05
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.10
6.03.03.05
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.11
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.12
6.03.03.05
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.13
6.03.03.05
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.14
6.03.03.05
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.15
6.03.03.05
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.16
6.03.03.05
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.17
6.03.03.05
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.18
6.03.03.05
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.19
6.03.03.05
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.20
6.03.03.05
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.21
6.03.03.05
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.22
6.03.03.05
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.23
6.03.03.05
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.24
6.03.03.05
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.25
6.03.03.05
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.26
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.27
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.28
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.29
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.30
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.31
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.32
6.03.03.05
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-HETL-PS-SEPT2.33
6.03.03.05
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.34
6.03.03.05
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.35
6.03.03.05
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.36
6.03.03.05
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.37
6.03.03.05
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.38
6.03.03.05
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.39
6.03.03.05
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.40
6.03.03.05
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.41
6.03.03.05
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.42
6.03.03.05
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.43
6.03.03.05
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.44
6.03.03.05
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.45
6.03.03.05
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.46
6.03.03.05
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-PS-SEPT2.47
6.03.03.05
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.09
6.03.03.01
The magnet length shall be <0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.10
6.03.03.01
The magnet slot length shall be 0.825 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.11
6.03.03.01
The magnets dipole field B shall be 1.399 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.09
6.03.03.01
The magnet length shall be <0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.10
6.03.03.01
The magnet slot length shall be 0.5455 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.11
6.03.03.01
The magnets dipole field B shall be 1.298 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH2.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH2.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.09
6.03.03.01
The magnet length shall be <0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.10
6.03.03.01
The magnet slot length shall be 0.117 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.11
6.03.03.01
The magnets dipole field B shall be 0.881 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DH3.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DH3.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.09
6.03.03.01
The magnet length shall be <1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.10
6.03.03.01
The magnet slot length shall be 1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.11
6.03.03.01
The magnets dipole field B shall be 0.061 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-DV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-DV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KH1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KH1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.03
6.03.03.01
The magnet field direction shall be H (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.06
6.03.03.01
The magnet minimal gap shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.11
6.03.03.01
The magnets dipole field B shall be 0.002 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-KV1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-KV1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.09
6.03.03.01
The magnet length shall be <0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.10
6.03.03.01
The magnet slot length shall be 0.1 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.12
6.03.03.01
The magnets gradiant field G shall be 39.784 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q1.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q1.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.02
6.03.03.01
The magnet field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.3
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.04
6.03.03.01
The magnet field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.05
6.03.03.01
The magnet minimal coil inner radius shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.09
6.03.03.01
The magnet length shall be <0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.10
6.03.03.01
The magnet slot length shall be 0.2794 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.11
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.12
6.03.03.01
The magnets gradiant field G shall be 26.684 T/m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-Q_BATES.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-Q_BATES.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.02
6.03.03.01
The magnet field type shall be Di (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.03
6.03.03.01
The magnet field direction shall be V (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.06
6.03.03.01
The magnet minimal gap shall be 32 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.09
6.03.03.01
The magnet length shall be <0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.10
6.03.03.01
The magnet slot length shall be 0.5 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.11
6.03.03.01
The magnets dipole field B shall be 0.896 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SEPTUM.55
6.03.03.01
The magnets shall not be designed to constrain the ext. fringe feild requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SEPTUM.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.01
6.03.03.01
The magnet shall have a single function.
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.02
6.03.03.01
The magnet field type shall be So (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.03
6.03.03.01
The magnet field direction shall be Z (V=vertical,H=horizontal,Z=beam direction )
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.4
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.5
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.6
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.07
6.03.03.01
The magnet good field aperture drx shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.08
6.03.03.01
The magnet good field aperture dry shall be TBD m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.09
6.03.03.01
The magnet length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.10
6.03.03.01
The magnet slot length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.11
6.03.03.01
The magnets dipole field B shall be 3.667 T
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.12
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.13
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.14
6.03.03.01
The magnets field stability shall be TBD T/s
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.15
6.03.03.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.16
6.03.03.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.17
6.03.03.01

05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.18
6.03.03.01
The Bore multipole content shall have a 1st order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.19
6.03.03.01
The Bore multipole content shall have a 2nd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.20
6.03.03.01
The Bore multipole content shall have a 3rd order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.21
6.03.03.01
The Bore multipole content shall have a 4th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.22
6.03.03.01
The Bore multipole content shall have a 5th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.23
6.03.03.01
The Bore multipole content shall have a 6th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.24
6.03.03.01
The Bore multipole content shall have a 7th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.25
6.03.03.01
The Bore multipole content shall have a 8th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.26
6.03.03.01
The Bore multipole content shall have a 9th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.27
6.03.03.01
The Bore multipole content shall have a 10th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.28
6.03.03.01
The Bore multipole content shall have a 11th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.29
6.03.03.01
The Bore multipole content shall have a 12th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.30
6.03.03.01
The Bore multipole content shall have a 13th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.31
6.03.03.01
The Bore multipole content shall have a 14th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.32
6.03.03.01
The Bore multipole content shall have a 15th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.33
6.03.03.01
The Bore multipole content shall have a 16th order of TBD (10^-4)
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.34
6.03.03.01
The magnet shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.35
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.36
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.37
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.38
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.39
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.40
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.41
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.42
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.43
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.44
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.45
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.46
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.47
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.48
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.49
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.50
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.51
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.52
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.53
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.54
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-MAG-SPINSOL.55
6.03.03.01
The magnets shall not be designed to limit Xtalk Requirements
05/16/2025
In Process
FALSE

P-EIS-METL-MAG-SPINSOL.56
6.03.03.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH2.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH2.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DH3.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DH3.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-DV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-DV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KH1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KH1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-KV1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-KV1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q1.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q1.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-Q_BATES.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-Q_BATES.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SEPTUM.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SEPTUM.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.01
6.03.03.02
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.02
6.03.03.02
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.03
6.03.03.02
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.04
6.03.03.02
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.5
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.06
6.03.03.02
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.07
6.03.03.02
The nominal current of the magnets being powered shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.08
6.03.03.02
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.09
6.03.03.02
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.10
6.03.03.02
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.11
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.12
6.03.03.02
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.13
6.03.03.02
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.14
6.03.03.02
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.15
6.03.03.02
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.16
6.03.03.02
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.17
6.03.03.02
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.18
6.03.03.02
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.19
6.03.03.02
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.20
6.03.03.02
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.21
6.03.03.02
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.22
6.03.03.02
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.23
6.03.03.02
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.24
6.03.03.02
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.25
6.03.03.02
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.26
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.27
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.28
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.29
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.30
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.31
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.32
6.03.03.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-METL-PS-SPINSOL.33
6.03.03.02
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.34
6.03.03.02
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.35
6.03.03.02
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.36
6.03.03.02
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.37
6.03.03.02
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.38
6.03.03.02
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.39
6.03.03.02
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.40
6.03.03.02
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.41
6.03.03.02
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.42
6.03.03.02
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.43
6.03.03.02
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.44
6.03.03.02
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.45
6.03.03.02
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.46
6.03.03.02
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-PS-SPINSOL.47
6.03.03.02
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.11
6.03.02.01.03
-10<b11<10 , -10<a11<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.12
6.03.02.01.03
b12 -10<b12<10 , -10<a12<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.13
6.03.02.01.03
b13 -10<b13<10 , -10<a13<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.14
6.03.02.01.03
b14 -10<b14<10 , -10<a14<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.15
6.03.02.01.03
b15 -10<b15<10 , -10<a15<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.16
6.03.02.01.03
b16 -10<b16<10 , -10<a16<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.01
6.03.02.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.05
6.03.02.02
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.06
6.03.02.02
The magnet field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.09
6.03.02.02
The minimum magnet bore gap shall be 40 (mm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.12
6.03.02.02
The magnet physical length of the magnet shall be <1.77 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15
6.03.02.02
The magnet integrated dipole field (min/max) B shall be 0.081\0.49 (Tm).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.15.1
6.03.02.02
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.08256 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.15.2
6.03.02.02
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.4896 na.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.17
6.03.02.02
The magnet field ramp rate shall be 2.55 (T/s).
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.18
6.03.02.02
The magnet to magnet field variability between magnets shall be < 0.1 %.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.19
6.03.02.02
The harmonic reference radius for all energy levels (3, 5, 10, and 18 Gev) shall be 15 (mm) centered at (0,0) with respect to the magnetic axis.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.20
6.03.02.02
The field at the reference radius shall be: 0.046 (T) at 3 Gev TBD (T) at 5 Gev TBD (T) at 10 GeV 0.277 (T) at 18 Gev
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21
6.03.02.02
At the magnet the bore field shall have the following multipole content (units in 10^-4):
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.1
6.03.02.02
b1 = 10000 , a1 = 0
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.2
6.03.02.02
-2.3 < b2 < 2.3 , -0.1 < a2 < 0.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.4
6.03.02.02
-0.1 < b4 < 0.1 , 0 < a4 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.5
6.03.02.02
0.4 < b5 < 3 , 0 < a5 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.6
6.03.02.02
-0.1 < b6 < 0.1 , 0 < a6 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.7
6.03.02.02
-2 < b7 < 2 , 0 < a7 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.8
6.03.02.02
-1 < b8 < 1 , 0 < a8 < 0.2
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.9
6.03.02.02
-1 < b9 < 0 , 0.9 < a9 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.21.11
6.03.02.02
0 < b11 < 2 , 0.9 < a11 < 1.1
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-D0.22
6.03.02.02
The magnet shall be designed to limit CrossTalk requirements.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.23
6.03.02.02
The magnet xtalk shall be constrained as described ; The dipoles shall be designed such that the crosstalk between successive dipoles in the ring is low eNugh to prevent the field from the adjacent dipoles having a significant effect on the beam. The residual crosstalk will need to be approved by beam physics.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.27
6.03.02.02
The magnet has no specific constraints for external fringe field.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.29
6.03.02.02
Magnetic field position and alignment within the magnet, TBG
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.30
6.03.02.02
The magnet shall be designed to fit within the following envelope. TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.31
6.03.02.02
Magnet installation tolerances, TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.32
6.03.02.02
The magnet shall be designed to have a splitable pole to accommodate the Vacuum beam pipe installation.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.46
6.03.02.02
The magnet design and verification process shall ensure the final magnet will meet the reliability needs of the EIC over it planned operational life of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-D0.47
6.03.02.02
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of 20 years.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.01
6.03.02.01.01
The magnet shall have two functions. A magnet and a magnet
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.02
6.03.02.01.01
The magnet function shall require trim coils capable of trimming the field of the magnet by +\- 0.05 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.03
6.03.02.01.01
The magnet function shall require current taps for operation TBD (y/n)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.04
6.03.02.01.01
The magnet function shall require shunt(s) for operation TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.05.01
6.03.02.01.01
The main quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.05.02
6.03.02.01.01
The trim quadrupole shall have a Quadrupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.07
6.03.02.01.01
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.9
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.10
6.03.02.01.01
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.11
6.03.02.01.01
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.12
6.03.02.01.01
The magnet physical length of the magnet shall be <0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.13
6.03.02.01.01
The magnet model length shall be 0.6 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.14
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.15.2
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.16.1.1
6.03.02.01.01
For the main quadrupole at 3GeV Injection the Integrated grad field G shall be 2.58 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.1
6.03.02.01.01
For the trim quadrupole at 3GeV Injection the Integrated grad field G shall be 0.129 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.16.2.2
6.03.02.01.01
For the trim quadrupole at 18GeV Extraction the Integrated grad field G shall be 0.765 T/m.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.17
6.03.02.01.01
For the magnet at 3GeV Injection the peak ramp rate shall be 0.25 (T/m.s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.18
6.03.02.01.01
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.19
6.03.02.01.01
For magnet at 3GeV Injection the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.20
6.03.02.01.01
For magnet at 3GeV Injection the Field at the reference radius and design energy of 18 GeV shall be 4.3(T.m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21
6.03.02.01.01
At 3GeV Injection the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.1
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.21.2
6.03.02.01.01
b2=10000 , a2=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.4
6.03.02.01.01
-2<b4<2 , -0.1<a4<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.5
6.03.02.01.01
-10<b5<10 , -0.1<a5<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.6
6.03.02.01.01
0.4<b6<2.4 , -0.1<a6<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.7
6.03.02.01.01
-10<b7<10 , -0.1<a7<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.8
6.03.02.01.01
-1<b8<1 , -0.1<a8<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.9
6.03.02.01.01
-10<b9<10 , -0.1<a9<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.11
6.03.02.01.01
-10<b11<10 , -0.1<a11<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.12
6.03.02.01.01
b12 -2<b12<2 , -0.1<a12<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.13
6.03.02.01.01
b13 -10<b13<10 , -0.1<a13<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.14
6.03.02.01.01
b14 -7.1<b14<10.9 , -0.1<a14<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.15
6.03.02.01.01
b15 -10<b15<10 , -0.1<a15<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.21.16
6.03.02.01.01
b16 -10<b16<10 , -0.1<a16<0.1 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-Q0.34
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.35
6.03.02.01.01
The grad field G shall be T/m(n-1)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.36
6.03.02.01.01
The ramp rate shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.37
6.03.02.01.01
The field stability shall be T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.38
6.03.02.01.01
The harmonic reference Radius and current shall be (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.39
6.03.02.01.01
The Field at the reference radius and current shall be (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.40
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0.41
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.42
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.43
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.44
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.45
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.46
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.47
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.48
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.49
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.50
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.51
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.52
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.53
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.54
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.55
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0.56
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.01
6.03.02.01.01
The number of magnet functions shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.02
6.03.02.01.01
The field type shall be Qu (Di,Qu,Sx,Oc,De,Do,Sol,Ki,Hk,Vk,Se)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.3
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.04
6.03.02.01.01
The field rotation shall be No (No=norm, Sk=skew)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.05
6.03.02.01.01
The min coil inner rad shall be 16 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.6
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.07
6.03.02.01.01
The good field aperture drx required shall be 20.25 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.08
6.03.02.01.01
The good field aperture dry required shall be 7.61 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.09
6.03.02.01.01
The mag length shall be <0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.10
6.03.02.01.01
The eff Length shall be 0.6 m
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.11
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.12
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.13
6.03.02.01.01
The ramp rate shall be 2.2 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.14
6.03.02.01.01
The field stability shall be *1000 T/s
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.15
6.03.02.01.01
The harmonic reference Radius and current shall be Ir=TBD[A]\Rr=16[mm] (mm,A)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.16
6.03.02.01.01
The Field at the reference radius and current shall be Bref=TBD (T)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.17
6.03.02.01.01
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-Q0_6.18
6.03.02.01.01
The Bore multipole content shall have a 1st order of - (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.19
6.03.02.01.01
The Bore multipole content shall have a 2nd order of b2=10000 , a2=0 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.20
6.03.02.01.01
The Bore multipole content shall have a 3rd order of -7<b3<7 , 0<a3<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.21
6.03.02.01.01
The Bore multipole content shall have a 4th order of -2<b4<2 , 0<a4<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.22
6.03.02.01.01
The Bore multipole content shall have a 5th order of -10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.23
6.03.02.01.01
The Bore multipole content shall have a 6th order of 0.4<b6<2.4 , 0<a6<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.24
6.03.02.01.01
The Bore multipole content shall have a 7th order of -10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.25
6.03.02.01.01
The Bore multipole content shall have a 8th order of -1<b8<1 , 0<a8<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.26
6.03.02.01.01
The Bore multipole content shall have a 9th order of -10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.27
6.03.02.01.01
The Bore multipole content shall have a 10th order of -1.3<b10<4.7 , 0<a10<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.28
6.03.02.01.01
The Bore multipole content shall have a 11th order of -10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.29
6.03.02.01.01
The Bore multipole content shall have a 12th order of -2<b12<2 , 0<a12<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.30
6.03.02.01.01
The Bore multipole content shall have a 13th order of -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.31
6.03.02.01.01
The Bore multipole content shall have a 14th order of -7.1<b14<10.9 , 0<a14<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.32
6.03.02.01.01
The Bore multipole content shall have a 15th order of -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-Q0_6.33
6.03.02.01.01
The Bore multipole content shall have a 16th order of -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.11
6.03.02.01.02
-10<b11<10 , 0<a11<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.12
6.03.02.01.02
b12 -10<b12<10 , 0<a12<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.13
6.03.02.01.02
b13 -10<b13<10 , 0<a13<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.14
6.03.02.01.02
b14 -10<b14<10 , 0<a14<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.15
6.03.02.01.02
b15 -10<b15<10 , 0<a15<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.16
6.03.02.01.02
b16 -10<b16<10 , 0<a16<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-PS-C0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.07
6.03.02.03
The nominal current of the magnets being powered shall be 12.713724 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-C0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-C0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.07
6.03.02.03
The nominal current of the magnets being powered shall be 2111.2 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-D0.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-D0.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.07
6.03.02.03
The nominal current of the magnets being powered shall be 1095.9 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-Q0_6.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.26
6.03.02.03
The voltage tap configuration shall be N/A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.27
6.03.02.03
The threshold levels shall be N/A V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.28
6.03.02.03
The peak di/dt without inducing a quench shall be N/A A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.29
6.03.02.03
The design shall have quench heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.30
6.03.02.03
The quench heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.31
6.03.02.03
The design shall have warm up heaters N/A Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.32
6.03.02.03
The warmup heater power rating shall be N/A W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-Q0_6.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.01
6.03.02.03
The number of Independent functions on the magnets being powered shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.02
6.03.02.03
The maximum magnet string resistance to be powered shall be TBD ohm
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.03
6.03.02.03
The maximum magnet string inductance to be powered shall be TBD H
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.04
6.03.02.03
The magnets being powered shall be saturated TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.5
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.06
6.03.02.03
The voltage to ground of the magnet being powered shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.07
6.03.02.03
The nominal current of the magnets being powered shall be 580 A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.08
6.03.02.03
The minimum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.09
6.03.02.03
The maximum current the PS must operate at shall be TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.10
6.03.02.03
The PS current type shall be DC (DC or AC)
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.11
6.03.02.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-PS-SXT.12
6.03.02.03
The peak waveshape di/dt during ramping shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.13
6.03.02.03
The full power bandwidth required shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.14
6.03.02.03
The ppm of full scale current (peak to peak) shall be TBD %
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.15
6.03.02.03
The time period for specified stability shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.16
6.03.02.03
The short term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.17
6.03.02.03
The long term stability shall be TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.18
6.03.02.03
The current setpoint resolution (min size in bits) shall be TBD bits
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.19
6.03.02.03
The synchronization required between PS's shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.20
6.03.02.03
The synchronization timing of synchronization shall be TBD s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.21
6.03.02.03
The max allowable current ripple (peak to peak) TBD A
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.22
6.03.02.03
The max current ripple frequency range (Hz) TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.23
6.03.02.03
WRT the ripple frequency the following resonant frequencies shall be avoided TBD Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.24
6.03.02.03
The max voltage ripple (peak to peak) shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.25
6.03.02.03
An NMR shall be required to measure the field TBD A/s
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.26
6.03.02.03
The voltage tap configuration shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.27
6.03.02.03
The threshold levels shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.28
6.03.02.03
The peak di/dt without inducing a quench shall be TBD A/S
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.29
6.03.02.03
The design shall have quench heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.30
6.03.02.03
The quench heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.31
6.03.02.03
The design shall have warm up heaters TBD Y/N
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.32
6.03.02.03
The warmup heater power rating shall be TBD W
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.33
6.03.02.03
The current required to be shunted through the magnet shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.34
6.03.02.03
The magnet turns ratio shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.35
6.03.02.03
The terminal voltage shall be TBD V
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.36
6.03.02.03
The design shall have thermal switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.37
6.03.02.03
The thermal switch connection numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.38
6.03.02.03
The design shall have water flow switches TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.39
6.03.02.03
The water flow switch connections numbers shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.40
6.03.02.03
The design shall have access controls interlocks TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.41
6.03.02.03
The main terminals lug details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.42
6.03.02.03
The lead end indications shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.43
6.03.02.03
The lugs details for thermal switch and water switches shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.44
6.03.02.03
The lug details for the auxiliary windings shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.45
6.03.02.03
The A/B terminal labeling details shall be TBD Draw id
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.46
6.03.02.03
The magnet drawing with terminations details shall be TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-PS-SXT.47
6.03.02.03
The magnet polarity connections shall be TBD
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.03
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.04
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.05
6.05.02.01
The magnet is a Dipole(D5I) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5I.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5I.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5I.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D5O.03
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.04
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.05
6.05.02.01
The magnet is a Dipole(D5O) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D5O.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D5O.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D5O.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D6.03
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.04
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.05
6.05.02.01
The magnet is a Dipole(D6) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D6.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D6.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D6.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D8.03
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.04
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.05
6.05.02.01
The magnet is a Dipole(D8) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D8.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D8.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D8.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

P-HSR-MAG-D9.03
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the multipole homogeneity measurements and transfer function are maintained in the BNL magnet repository.
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.04
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Cross-talk calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.05
6.05.02.01
The magnet is a Dipole(D9) RHIC Magnet, the Magnet-Fringe-field calculations are maintained in the BNL magnet repository.
08/15/2025
In Process
FALSE

P-HSR-MAG-D9.06
6.05.02.01
The magnet shall be designed to be cooled and sustained at its operational temperature utilizing the proposed EIC cryogenic system which meets the following constraints:
05/16/2025
In Process
FALSE

P-HSR-MAG-D9.07
6.05.02.01
The magnet shall have an appropriate Magnet-Quench protection system which ensures all electromagnetic, thermal and cryogenic connected systems are not damaged in a Magnet-Quench event and meets the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.08
6.05.02.01
All Magnet-Electrical connection to the magnet for the main current leads, instrumentation, Voltage taps, Current taps shall meet the appropriate interface requirements specified for those connections and meet the following constraints:
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.09
6.05.02.01
The magnet is expected to sustain 20 years of EIC operation under nominal conditions. During these 20 operational years, the magnet is expected to survive the following: 40 thermal cycles, 120 Magnet-Quenches and 20000 power cycles.
08/15/2025
Approved
FALSE

P-HSR-MAG-D9.10
6.05.02.01
The magnet shall be designed to operate reliably given the cumulative radiation dose it will experience over the lifetime of the EIC of >20 Years.
05/16/2025
Approved
FALSE

EIS- RCS-MAG EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS- RCS-MAG.3
6.03.02
The sextupoles shall be sorted into appropriate “families” and powered accordingly.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.4
6.03.02
There shall be dipole correctors capable of adjusting the beam orbit.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.6
6.03.02
The quadrupoles shall generally be arranged in a conventional FODO structure.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.7
6.03.02
Each quadrupole strength needs to be capable of being changed independently by small amounts for beam-based alignment purposes.
05/16/2025
In Process
FALSE

F-EIS- RCS-MAG.8
6.03.02
Sextupoles shall be sorted into “families” with the family structure dependent on the linear lattice configuration (betatron phase advance per FODO cell).
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.9
6.03.02
The maximum integrated field strength of the FODO sextupoles needs to be sufficient to correct chromaticity to within 1 unit in both planes.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-S0.01
6.03.02.01.02
The magnet shall have a single function.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.3
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.4
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.05
6.03.02.01.02
The magnet shall have a Sextupole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.6
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.07
6.03.02.01.02
The magnet shall have a normal field rotation.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.9
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.10
6.03.02.01.02
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.11
6.03.02.01.02
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.12
6.03.02.01.02
The magnet physical length of the magnet shall be <0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.13
6.03.02.01.02
The magnet model length shall be 0.5 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.14
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.15
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.16.1
6.03.02.01.02
For the magnet at 3GeV Injection the Integrated grad field G shall be 15.3 T/m2.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.17
6.03.02.01.02
For the magnet at 3GeV Injection the peak ramp rate shall be 2.73(T/m2.S)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.18
6.03.02.01.02
For the magnet at 3GeV Injection the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.19
6.03.02.01.02
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.20
6.03.02.01.02
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 30.5(T.m^2)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21
6.03.02.01.02
The magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.1
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.2
6.03.02.01.02
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-S0.21.4
6.03.02.01.02
-10<b4<10 , 0<a4<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.5
6.03.02.01.02
-10<b5<10 , 0<a5<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.6
6.03.02.01.02
-10<b6<10 , 0<a6<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.8
6.03.02.01.02
-10<b8<10 , 0<a8<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.7
6.03.02.01.02
-10<b7<10 , 0<a7<0.2 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-S0.21.9
6.03.02.01.02
-10<b9<10 , 0<a9<0.2 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.10
6.03.02
Window-frame dipole corrector magnets capable of providing both horizontal and vertical dipole fields to correct the beam orbit in both transverse planes shall be placed adjacent to most of the quadrupoles.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

F-EIS- RCS-MAG.11
6.03.02
The strength of the window-frame dipole correctors needs to be chosen to correct for any source of orbit distortion and should have a margin for beam based diagnostic purpose.
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.01
6.03.02.01.03
The magnet shall have two functions. A H-corrector and a V-corrector
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.2
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.3
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.4
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.05
6.03.02.01.03
The magnet shall have a Dipole field.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.01
6.03.02.01.03
The H-corrector field shall have a vertical field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.06.02
6.03.02.01.03
The V-corrector field shall have a horizontal field direction.
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.7
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.09
6.03.02.01.03
The magnet bore gap Gh and width Gw shall be Gh=40,Gw=TBD (mm)
05/16/2025
In Process
FALSE

P-EIS-RCS-MAG-C0.10
6.03.02.01.03
The magnet good field aperture dAx required shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.11
6.03.02.01.03
The magnet good field aperture dAy required shall be 5 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.12
6.03.02.01.03
The magnet physical length of the magnet shall be <0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.13
6.03.02.01.03
The magnet model length shall be 0.33 (m)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.14
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.15.1
6.03.02.01.03
For the magnet at 3GeV Injection the integrated dipole field B shall be 0.00132 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.15.2
6.03.02.01.03
For the magnet at 18GeV Extraction the integrated dipole field B shall be 0.00759 T.m
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.16
6.03.02.01.03
< blank >
05/16/2025
Not Applicable
FALSE

P-EIS-RCS-MAG-C0.17
6.03.02.01.03
For the magnet at the peak ramp rate shall be 0.00027 (T/s)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.18
6.03.02.01.03
For the magnet at the magnet-to-magnet field variability shall be < 0.001 (%)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.19
6.03.02.01.03
For magnet at the harmonic reference radius at the design energy of 18 GeV shall be 15 (mm)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.20
6.03.02.01.03
For magnet at the Field at the reference radius and design energy of 18 GeV shall be 0.0004(T)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21
6.03.02.01.03
At the magnet the bore field shall have the following multipole content:
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.1
6.03.02.01.03
b1=10000 , a1=0 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.2
6.03.02.01.03
-10<b2<10 , -10<a2<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.4
6.03.02.01.03
-10<b4<10 , -10<a4<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.5
6.03.02.01.03
-10<b5<10 , -10<a5<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.6
6.03.02.01.03
-10<b6<10 , -10<a6<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.8
6.03.02.01.03
-10<b8<10 , -10<a8<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.7
6.03.02.01.03
-10<b7<10 , -10<a7<10 (10^-4)
05/16/2025
Approved
FALSE

P-EIS-RCS-MAG-C0.21.9
6.03.02.01.03
-10<b9<10 , -10<a9<10 (10^-4)
05/16/2025
Approved
FALSE

EIS-BAR

EIS-CNTRL

EIS-CNTRL EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-CNTRL.1
6.07.02
The EIS control system shall facilitate all IR global control requirements.
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

F-EIS-CNTRL.2
6.07.02
The EIS control system shall facilitate all network, relational database and data archiving required.
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

F-EIS-CNTRL.3
6.07.02
The control system shall facilitate all machine protection systems required
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

F-EIS-CNTRL.4
6.07.02
The EIS control system shall facilitate all EIC machine timing required.
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT-INJ.01
6.07.02
Placeholder , Tuning requirements Should be listed here and/or under transfer lines in 6.03 shall be tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

F-EIS-CNTRL.5
6.07.02
The EIS control system shall facilitate fast feedback integration systems required.
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

F-EIS-CNTRL.6
6.07.02
The EIS control system shall facilitate all physics application support required.
05/16/2025
In Process
FALSE

P-EIS-GUN-CONT.02
6.07.02
The spin state control command window prior to laser trigger shall be 10 ms
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.01
6.07.02
The polarization monitoring rate shall be 8 bunches at 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-CONT.03
6.07.02
PlaceHolder- Other Gun\source controil requirements? - -
05/16/2025
On Hold
FALSE

P-EIS-RCS-CONT.01
6.07.02
The beam based alignment shall power the quadrapole magnets to +/- .15 k1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.02
6.07.02
The beam based alignment BPM's shall be placed in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.03
6.07.02
The orbit display rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.04
6.07.02
The orbit feed-forward optimization rate shall be 1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.05
6.07.02
The orbit corrections sampling rate shall be 78 kHz
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.06
6.07.02
The tunes feed-forward optimization period shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.07
6.07.02
The chromaticity feed-forward optimization rate shall be 6 hrs +/- 1
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.08
6.07.02
The fast context switching available PPM contexts shall be 8 cnt
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.09
6.07.02
The fast context switching shall apply to selected RF components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.10
6.07.02
The fast context switching shall apply to selected PS components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.11
6.07.02
The fast context switching shal apply to selected Inst components in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.12
6.07.02
The fast context switching shall support manual and automated control in the following locations tbd
05/16/2025
In Process
FALSE

P-EIS-RCS-CONT.13
6.07.02
The fast context switching min context switching period shall be 1 sec
05/16/2025
In Process
FALSE

EIS-INST

EIS-INST EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-INST.1
6.03.04
EIS shall have all the beam instrumentation necessary to deliver the operational parameters set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-HETL-INST-BPM-ELEC.01
6.03.03.04.01
The BPM single bunch measurement resolution for a (1 - 4 nC) pilot bunch shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.02
6.03.03.04.01
The BPM single bunch measurement resolution for (5.5 - 28 nC) bunches shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.03
6.03.03.04.01
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.04
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used to measure the transport lattice.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.01
6.03.03.04.01
The BPM Pickup alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.02
6.03.03.04.01
The BPM Pickup shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM-PU.04
6.03.03.04.01
The BPM Pickups shall be located by the dipole correctors at every second quadrupole.
05/16/2025
Approved
FALSE

P-EIS-HETL-INST-BPM.01
6.03.03.04
The BPM measurement resolution should be 100 um or less, for a bunch charge range of 100 pc to 28 nC. < 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall depend on the rate of transfer from RCS-to-ESR, expected twice per second. 2.5 uS
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.03
6.03.03.04
The number of BPMs in the RCS-to-ESR transport line shall be 10 ea
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.04
6.03.03.04
The BPMs shall be located by the dipole correctors at every 2nd Quad
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy to each nearby quad shall be within 100 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated TBD degree configuration to avoid the synch light near the dipole bends
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedforward to optimize transmission efficiency
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the transport lattice.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-BPM.09
6.03.03.04
The BPMs located in the high dispersion regions, shall monitor relative changes in the beam energy.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency of the Line
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-CM.06
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the ESR
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.01
6.03.03.04.03
The optical resolution for beam profile measurements shall be < 50 um
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.02
6.03.03.04.03
A single YAG/OTR PM station shall be located at a dispersive location and used to determine the beam energy spread.
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.03
6.03.03.04.03
The "energy spread PM" station shall be able to measure the beam energy over the range TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.04
6.03.03.04.03
The "energy spread PM station" shall be able to measure the beam energy with a resolution of 2.5 10-3 rms units
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.05
6.03.03.04.03
Multiple, strategically located YAG/OTR screens shall be used in combination for beam emittance measurements
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.06
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
In Process
FALSE

P-EIS-HETL-INST-PM.07
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM-ELEC.01
6.03.03.04.01
For a (1 nC) pilot bunch, the BPM single bunch measurement resolution shall be < 1mm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.02
6.03.03.04.01
For (5.5 - 10 nC) bunches, the BPM single bunch measurement resolution shall be < 100microns
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.03
6.03.03.04.01
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.04
6.03.03.04.01
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.05
6.03.03.04.01
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-ELEC.06
6.03.03.04.01
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.01
6.03.03.04.01
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.02
6.03.03.04.01
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.03
6.03.03.04.01
The number of BPM Pickups in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM-PU.04
6.03.03.04.01
The location of the BPM Pickups shall be TBD
05/16/2025
Approved
FALSE

P-EIS-METL-INST-BPM.01
6.03.03.04
For a bunch charge range of 100 pc to 10 nC, the BPM measurement resolution shall better than 100 um
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.02
6.03.03.04
The BPM acquisition rate shall be up to 100 Hz
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.03
6.03.03.04
The number of BPMs in the Linac-to-RCS transport line shall be TBD ea
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.04
6.03.03.04
The location of the BPMs shall be TBD
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.05
6.03.03.04
The BPM pick-up alignment accuracy with respect to to its nearby quadrapole magnet shall be better than 100 µm
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.06
6.03.03.04
The BPM button style pick-ups shall be rotated 45 degree configuration to avoid the synch light near the dipole bends.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.07
6.03.03.04
The BPMs shall be used as input for beam trajectory correction and/or feedback to optimize transmission efficiency.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.08
6.03.03.04
The BPMs shall be used to measure the beam energy and characterize the accelerator lattice.
05/16/2025
In Process
FALSE

P-EIS-METL-INST-BPM.09
6.03.03.04
The beam energy measurement resolution shall be 0.4 MeV
05/16/2025
In Process
FALSE

P-EIS-METL-INST-CM.01
6.03.03.04.02
An ICT and FCT shall be installed near the end of the transfer line.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.02
6.03.03.04.02
The bunch charge shall be measured with an accuracy better than <1 %
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.03
6.03.03.04.02
The bunch charge shall be measured with the resolution of 10 pC
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.04
6.03.03.04.02
The bunch charge monitor shall be used to measure transport efficiency.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.05
6.03.03.04.02
The FCT shall provide measurements of the bunch patterns being transported to the RCS.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.06
6.03.03.04.02
The number of ICTs in transfer line shall be 3 ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-CM.07
6.03.03.04.02
The number of FCTs in transfer line shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.01
6.03.03.04.03
The transfer line shall include plunging YAG/OTR screens to measure beam position, transverse profiles and beam emittance measurements.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.02
6.03.03.04.03
The optical resolution for beam profile measurements shall be 50 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.03
6.03.03.04.03
A YAG/OTR station at a dispersive location shall be used to determine the beam energy spread.
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.04
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam energy spread of 1 MeV
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.05
6.03.03.04.03
The measurement capability shall be appropriate to measure a beam emittance (Ref MPT Table 4.4.2.) for H & V of 35 um
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.06
6.03.03.04.03
The total number of profile monitors shall be TBD ea
05/16/2025
On Hold
FALSE

P-EIS-METL-INST-PM.07
6.03.03.04.03
The locations of the profile monitors shall be TBD
05/16/2025
On Hold
FALSE

P-EIS-RCS-INST-BPM-ELEC.01
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, single turn shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.02
6.03.02.05.01
Measurement resolution for (1 nC) pilot bunch, 100 turns average shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.03
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, (1 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.04
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.05
6.03.02.05.01
Measurement resolution for 4 bunch train & 2 bunch train (before merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.06
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, (1-4 nC) pilot bunch shall be < 1 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.07
6.03.02.05.01
Measurement resolution for single bunch (after merges), single turn, 5.5-28 nC bunches shall be < 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-ELEC.08
6.03.02.05.01
Measurement resolution for single bunch (after merges), 100 turns average, 5.5-28 nC bunches shall be < 10 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.01
6.03.02.05.01
BPM pick-up shall be located near each quadrupole magnet in the RCS
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.02
6.03.02.05.01
BPM pick-up shall be located with respect to the nearby quadrupole with alignment accuracy relative to closest quad of better than 100 microns
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.03
6.03.02.05.01
BPM pick-ups shall be designed to provide the required measurement resolution for a radial area around the center of +/-10 mm
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.04
6.03.02.05.01
BPM pick-ups design shall ensure the simulated impedance is within the accepted overall RCS impedance budget
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.05
6.03.02.05.01
The dual plane button style BPM Pickups shall be placed near the RCS focusing quads and rotated at 45 degrees to avoid synchrotron radiation.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-BPM-PU.06
6.03.02.05.01
The single plane button style BPM Pickups shall be placed near the defocusing quads will have a button on the top and bottom.
05/16/2025
Approved
FALSE

P-EIS-RCS-INST-CM.01
6.03.02.05.02
A DCCT shall be installed to measure the average current during the RCS cycle.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.02
6.03.02.05.02
The performance of the DCCT system shall be equivalent to what is provided by the COTS Bergoz NPCT system
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.03
6.03.02.05.02
Provisions shall be made to ensure thermal effects do not interfere with the quality of the average current measurement
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.04
6.03.02.05.02
The DCCT shall be able to measure the Individual bunch charges over a charge range of 5 to 28 nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.05
6.03.02.05.02
The DCCT shall be able to measure to an accuracy of tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.06
6.03.02.05.02
The DCCT shall be able to monitor the Bunch patterns tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.07
6.03.02.05.02
The location of the DCCT shall be tba -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.08
6.03.02.05.02
The locations of FCT shall be -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.09
6.03.02.05.02
The range of average beam current to be measured shall be 0. 390 to 4.4 mA
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.10
6.03.02.05.02
The DCCT system shall have a self calibration system -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.11
6.03.02.05.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.12
6.03.02.05.02
The measurement of the average current shall be provided to users at a rate of at least <0.1 Hz
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.13
6.03.02.05.02
The measurement of the average current shall have an RMS noise of less than 0.01 %
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.14
6.03.02.05.02
The digitizer sample rate of the DCCT measurement during the RCS cycle shall be 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.15
6.03.02.05.02
The measured average current shall be archived at a rate of 100 units
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.16
6.03.02.05.02
The DCCT sensor shall be radiation resistant
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.17
6.03.02.05.02
The DCCT shall operate in the temperature range of 15-35 degrees C 15-35 °C
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.18
6.03.02.05.02
Stray magnetic fields near the DCCT sensor shall not exceed 0.01 Gauss
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-CM.19
6.03.02.05.02
The DCCT sensor shall have the minimal impedance as seen by the beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.01
6.03.02.05.04
A synchrotron light monitor (SLM) shall be installed in the RCS ring downstream of an RCS dipole magnet
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.02
6.03.02.05.04
The location of the SLM light extraction port shall be- TBD
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.03
6.03.02.05.04
The synchrotron light shall be transported from the RCS light extraction port to an optical table for detection.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.04
6.03.02.05.04
The synchrotron light optical table shall have a streak camera and gated camera shall be installed.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.05
6.03.02.05.04
The SLM shall be able to make Turn-by-turn measurements using gated cameras to provide measurements of; the injection matching parameters and the beam position stability parameters during acceleration. TBD -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.06
6.03.02.05.04
The SLM shall be used to provide horizontal and vertical transverse profile measurements on bunches with charges > 6nC
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.07
6.03.02.05.04
The SLM horizontal and vertical transverse profile measurements shall be measured with a resolution in both planes of 0.1 mm
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.08
6.03.02.05.04
The SLM shall be used to provide longitudinal profile measurements
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.09
6.03.02.05.04
A dual sweep streak camera shall be used to provide measurements of the bunch length and longitudinal profiles
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.10
6.03.02.05.04
The dual sweep streak camera shall have a resolution of <5 ps
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.11
6.03.02.05.04
The profile measurements shall be used, together with modeled or measured beam optics to infer the beam emittances and energy spread.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.12
6.03.02.05.04
The Vertical emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.6 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.13
6.03.02.05.04
The Horizontal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 10 nm (un-norm)
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.14
6.03.02.05.04
The Longitudinal emittance measurement for bunch charges > 6nC, shall be measured with a precision of 0.00001 eV-s
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-SLM.15
6.03.02.05.04
The Energy spread measurement, for bunch charges > 6nC, shall be measured with a precision of 0.0001 dp/p
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.01
6.03.02.05
Stripline kickers (H & V) shall be installed in the RCS to kick the beam so tunes can be measured by the turn-by-turn BPMs as well as to blow up vertical emittance at end of ramp
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.02
6.03.02.05
The design of the kickers shall adhere to the impedance budget requirement for the RCS ring
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.03
6.03.02.05
The amount of kick that the horizontal and vertical kickers shall provide is 0.2 mrad
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.04
6.03.02.05
The kicker waveform parameters (pulse shape and length) shall be Pulse shape rectangular dt=2.4 to 5mS mS
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.05
6.03.02.05
The location of the kickers shall be near low beta value
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TM.06
6.03.02.05
The kickers HV PS's shall have the capability to pulse twice per second: Once for tune and once for emittance blow up
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.01
6.03.02.05.03
Plunging YAG/OTR PM screen stations will be installed in the RCS ring to facilitate commissioning and re-establishing beam
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.02
6.03.02.05.03
The YAG/OTR PM shall be located as follows : one in each straight section (6), and one after the injection septum(1). Making a Total of 7 -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.03
6.03.02.05.03
The exact locations in the straight sections shall be tbd -
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.04
6.03.02.05.03
The optical resolution for beam profile measurements shall be <50 microns
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.05
6.03.02.05.03
Each measurement station will provide three possible options, inserted YAG screen, inserted OTR screen, and an impedance matched sleeve connected with RF fingers during normal operations.
05/16/2025
In Process
FALSE

P-EIS-RCS-INST-TPM.06
6.03.02.05.03
Provisions shall be made so that the impedance match sleeve cannot be inadvertently retracted during normal operations.
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.01
6.04.06.02
A bunch pattern monitor shall be installed in the ESR to measure indiviual bunch charge with an accuracy 1 %
05/16/2025
In Process
FALSE

P-ESR-INST-BCM.02
6.04.06.02
The Bunch pattern monitor shall be capable of measuring Bunch patterns ranging from a single bunch, to a filled ring with 1,160 bunches
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.01
6.04.06.05
BLM shall be needed to needed to protect sensitive equipment.
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.02
6.04.06.05
The number of BLM installed in the ESR shall be TBD ea
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.03
6.04.06.05
BLM shall be installed at the following locations in the ESR TBD
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.04
6.04.06.05
The sensitivity of the BLM detectors shall be TBD units?
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.05
6.04.06.05
Where possible existing RHIC BLM's can be relocated to identify ESR & HSR losses
05/16/2025
In Process
FALSE

P-ESR-INST-BLM.06
6.04.06.05
The response time from loss detection to abort shall be TBD us
05/16/2025
In Process
FALSE

P-ESR-INST-BPM-ELEC.01
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following capabilities defined for the low intensity pilot injection energies and high intensity collision energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Electronics shall have the following time resolutions for data refresh defined for the beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.03
6.04.06.01
The ESR BPM Electronics shall have the following time resolutions for data logging defined for the beam energies:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.04
6.04.06.01
The ESR BPM Electronics shall have the following measurement resolutions defined for beam energies as defined in the Master Parameter Table: [EIC Document: EIC-SEG-RSI-005]:
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.05
6.04.06.01
The ESR BPM Electronics shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-ELEC.06
6.04.06.01
The ESR BPM Electronics shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/25/2025
Reviewed
FALSE

P-ESR-INST-BPM-PU.01
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall provide dual plane (horizontal and vertical) beam positional measurements.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.02
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) shall be positioned in the following locations approved by physics as defined in the lattice:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.03
6.04.06.01
The ESR Beam Position Monitor (BPM) Pick-Ups (PU) mechanical and electrical center in the locations identified shall be:
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.04
6.04.06.01
The ESR Beam Position Monitor Pick-Ups housing shall have a +/- 10 (mrad) corresponding to +/- 0.6 (degree) roll tolerance with regards to BPM measurements in respect to the vacuum chamber.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.05
6.04.06.01
The ESR Beam Position Monitor Pick-Ups design shall be less than or equal to the allocated impedance and is within the accepted overall ESR impedance budget approved by physics. (replace with loss factor)
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.06
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall fulfill resolution requirements over the horizontal and vertical beam position range with respect to its fiducials of +/- 3 (mm).
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.07
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to ensure the maximum temperatures of the components (due to heating by the beam) are acceptable for reliability and operations of the EIC over the planned operational life of 20 (yrs).
09/15/2025
In Process
FALSE

P-ESR-INST-BPM-PU.09
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to be baked to 250 °C for UHV processing.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.10
6.04.06.01
The ESR Beam Position Monitor Pick-Ups shall be designed to operate reliability with capability to withstand a lifetime radiation dose of TBD MGy.
07/25/2025
In Process
FALSE

P-ESR-INST-BPM-PU.11
6.04.06.01
The ESR BPM Pickup shall be designed to operate in an ambient temperature degree from X (C) to X (C).
07/30/2025
In Process
FALSE

P-ESR-INST-BPM-PU.12
6.04.06.01
The ESR Beam Position Monitor Button configuration will be mirror symmetric with respect to the mid-and center planes. Deviation from symmetry shall be such that corresponding BPM reading errors are less then 20 microns.
07/25/2025
Approved
FALSE

P-ESR-INST-BPM-PU.13
6.04.06.01
The ESR Beam Position Monitor Pick-Ups symmetrical configuration (postion between the four buttons and the relative to the fiducials on top of the button) shall be stable under the inference of the expected operational thermal changes to the extent that corresponding changes in the bpm reading deviate less than 20 µm.
07/25/2025
Approved
FALSE

P-ESR-INST-DCCT.01
6.04.06.02
A DCCT shall measure the average beam current in the ESR.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.02
6.04.06.02
The measurement resolution averaged over 1 sec shall be < 5 uA
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.03
6.04.06.02
The DCCT beamline device impedance shall be approved by beam physics.
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.04
6.04.06.02
Measurement drift tolerance (thermal effects) shall be ≤ 1 uA/K
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.05
6.04.06.02
The DCCT sensor in the ring shall operate in the temperature range of 15 to 35 degrees C
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.06
6.04.06.02
The range of average beam current to be measured shall be 0.156x10-3 to 2.5 A
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.07
6.04.06.02
The DCCT system shall have a remote controlled self calibration system
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.08
6.04.06.02
The DCCT system shall provide measurements with absolute accuracy of better than 0.2 %
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.09
6.04.06.02
The measured average current shall be provided to users at a rate of 10 Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.10
6.04.06.02
The measured average current shall be archived at a rate of 10 Hz Hz
05/16/2025
In Process
FALSE

P-ESR-INST-DCCT.11
6.04.06.02
The DCCT sensor assembly in the ring shall be radiation resistant
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.01
6.04.06.03
The requirements for longitudinal feedback are ??? TBD
05/16/2025
In Process
FALSE

P-ESR-INST-LONGIFB.02
6.04.06.03
The Longitudinal feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.01
6.04.06.04
The ESR shall have two synchrotron light monitors (SLM) and one X-ray pin hole monitor
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.02
6.04.06.04
The longitudinal bunch profile monitor shall have a turn-by-turn capability based on a single bunch in the fully filled bunch train.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.03
6.04.06.04
TThe SLM systems shall measure the crabbing angle, longitudinal bunch parameters, H & V beam size and global coupling.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.04
6.04.06.04
The SLM shall be able to measure a crabbing angle of 12.5 mrad with accuracy of 10 %
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.05
6.04.06.04
The SLM shall be able to measure the Longitudinal bunch parameters with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.06
6.04.06.04
The SLM shall be able to measure the H & V beam size with accuracy of H=?? V=?? units
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.07
6.04.06.04
The SLM shall be able to measure the Global coupling with accuracy of TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.08
6.04.06.04
One SLM port shall be located downstream of a dipole in an appropriate location in the ESR, exact location not critical.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.09
6.04.06.04
The second SLM port shall be located in a complimentary location in the lattice to ensure all the necessary SLM measurements can be made. TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.10
6.04.06.04
The SLM light extraction port mirrors shall be good quality, having a surface finish better than 1/10 Lambda
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.11
6.04.06.04
The SLM light extraction port mirrors shall be water cooled to avoid image distortion.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.12
6.04.06.04
There shall be an enclosed SL transport from the light extraction port to the SLM optical lab rooms. Length to be determined by the distance to optical lab room, should be minimized to reduce vibration problems.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.13
6.04.06.04
The locations of the SLM optical lab rooms shall be TBD -
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.14
6.04.06.04
The double-slit interferometer method shall be used to measure transverse beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.15
6.04.06.04
The standard transverse resolution of an SLM using visible light shall be ~60 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.16
6.04.06.04
The resolution using the double-slit method shall equal to 10 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.17
6.04.06.04
A streak camera shall be used to measure the bunch longitudinal profiles
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.18
6.04.06.04
A position sensitive photo-diode will provide photon beam centroid information which shall supplement the orbit stability measurements by the BPMs
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.19
6.04.06.04
A GigE CCD/CMOS camera, externally triggerable with exposure times ranging from 10 nsec to 5 sec, shall be used to image the visible radiation
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.20
6.04.06.04
A commercially available gated camera with gate width of <2 nsec (compared to a minimum bunch spacing of 10 nsec) shall be used to detect injection oscillations and for beam studies.
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.21
6.04.06.04
The location of the X-ray pinhole monitoring system shall be TBD
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.22
6.04.06.04
The target resolution of the X-ray pin hole monitoring system shall be ~ 5 um (or as best that can be achieved with the machine parameters and commercial equipment) 5 um
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.23
6.04.06.04
The X-ray pin hole monitor shall provide independent measurement of the energy spread and horizontal/vertical emittance. H=V=15.4 nm
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.24
6.04.06.04
The X-ray pinhole photon beamline shall be equipped with gated cameras that will be employed to provide high resolution turn-by-turn profile measurements
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.25
6.04.06.04
A pinhole assembly including tungsten slits shall provide sufficient resolution to precisely measure the beam size
05/16/2025
In Process
FALSE

P-ESR-INST-SLM.26
6.04.06.04
Several different size pinholes sizes shall be incorporated to allow easy alignment and measurements at different beam currents and energies.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.01
6.04.06.03
Stripline kickers (H & V) shall be used to excite the beam so tunes can be measured using turn-by-turn BPM data.
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.02
6.04.06.03
The magnitude of the kick required for the horizontal kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.03
6.04.06.03
The magnitude of the kick required for the vertical kicker shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.04
6.04.06.03
The kicker waveform (risetime and shape) requirements shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.05
6.04.06.03
The location of the tune meter kicker striplines in the ESR shall be TBD units
05/16/2025
In Process
FALSE

P-ESR-INST-TMK.06
6.04.06.03
The impedance of the kicker beamline device shall be approved by beam Physics.
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.01
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.03
6.04.06.03
Placeholder, Input needed TBD
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSFB.02
6.04.06.03
The transverse feedback systems shall be capable of counteracting single-bunch rise times of 1 ms
05/16/2025
In Process
FALSE

P-ESR-INST-TRANSSLFB.01
6.04.06.03
The transverse slow feedback system bandwidth shall bs 10 Hz
05/16/2025
In Process
FALSE

EIS-LETL : Gun Low Energy Transfer Line

EIS-PREINJ

EIS-PREINJ EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-PREINJ.1
6.03.04
The EIS Pre-Injector shall consist of 3 sub-systems: 1. An electron gun section, followed by 2. A low energy transfer line and bunching section, followed by 3. A LINAC section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PREINJ.2
6.03.04
The EIS Pre-Injector shall be able to create a spin polarized electron bunch and accelerate it to 400MeV ready for transport to the 400 MeV-transfer line to the RCS.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

F-EIS-PREINJ.3
6.03.04
The EIS Pre-Injector shall create bunches which meet the requirements set forth in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

EIS-PREINJ-BUNCH

EIS-PREINJ-BUNCH-INST

EIS-PREINJ-BUNCH-MAG

EIS-PREINJ-BUNCH-MOT

EIS-PREINJ-BUNCH-RF

EIS-PREINJ-BUNCH-VAC

EIS-PREINJ-GUN

F-EIS-PREINJ-GUN.5
6.03.04
Photocathode shall provide electron beam with sufficient polarization.
05/16/2025
In Process
FALSE

F-EIS-PREINJ-GUN.6
6.03.04
Laser shall perpendicular illuminate the cathode. First YAG beam viewer has a hole in center.
05/16/2025
In Process
FALSE

EIS-PREINJ-GUN EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-PREINJ-GUN.1
6.03.04
The pre-injector shall have a high voltage (HV) DC electron gun as the electron source for the EIC.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.2
6.03.04
The pre-injector electron gun shall produce all the bunch patterns required to deliver the ESR beam requirements set forth in [5.9].
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.3
6.03.04
When illuminated with a circular polarized laser the pre-injector electron gun shall produce the polarized electrons required to operate the EIC.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.4
6.03.04
The planned building utility requirements (Power, Temperature, Humidity, etc.) shall be consistent with the requirements necessary for the gun to meet its beam performance requirements
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-GUN.21
6.03.04
The diagnostic beamline solenoids shall be capable of maintaining the beam size in the diagnostic line up to either the Faraday cup or the Mott polarimeter.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.02
6.03.04.02
The Laser system requires a minimum voltage for electrical service 208 Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.03
6.03.04.02
The Laser power consumption shall be < 40 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.04
6.03.04.02
The Laser shall be cooled by chillers which also use the laser system power
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.05
6.03.04.02
The Laser cooling power shall not exceed 20 kW
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.06
6.03.04.02
The Laser shall be able to function in a clean room having an ambient temperature of 18 +/- 2 CO
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.07
6.03.04.02
The Laser shall have a repetition rate 0.623 MHz
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.08
6.03.04.02
The Laser pulse shall have a temporal profile 1.5 to 2 nS
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.09
6.03.04.02
The Laser shall operate at a wavelength of 780 +/-5 tunability range nm
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.10
6.03.04.02
The Laser shall be capable of generating a bunches having at least a spacing between bunches of <1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.11
6.03.04.02
The Laser Shall have the ability to flip and filter the laser pulses
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.13
6.03.04.02
The Laser pulse jitter rms shall not exceed <5 ps
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.12
6.03.04.02
The laser pulse shall have a transverse truncated gaussian profile
05/16/2025
On Hold
FALSE

P-EIS-GUN-LASER.14
6.03.04.02
The laser (power differential received at the cathode?) in the laser OFF and ON conditions shall be >60 dB
05/16/2025
On Hold
FALSE

EIS-PREINJ-LET

F-EIS-PREINJ-LET.2
6.03
The LET line shall have a spin rotator section to rotating spin direction from longitudinal to vertical.
08/20/2025
In Process
FALSE

F-EIS-PREINJ-LET.3
6.03
The low energy transfer line shall have an additional branch between the gun and the bunching section which can transfer individual electron bunches into the gun diagnostic beamline for commissioning the gun
08/20/2025
In Process
FALSE

F-EIS-PREINJ-LET.4
6.03
The low energy transfer line shall have a laser port in the dipole/differential pumping chamber, will allow an optical path for the laser to illuminate the cathode perpdicularlly.
08/20/2025
In Process
FALSE

F-EIS-PREINJ-LET.5
6.03
The gun diagnostic beamline section shall be able to dump the beam for the gun commissioning.
08/20/2025
In Process
FALSE

F-EIS-PREINJ-LET.8
6.03
Following the DC gun, the electron bunch shall be deflected through a bending dipole into the bunching section.
08/20/2025
In Process
FALSE

F-EIS-PREINJ-LET.9
6.03
Solenoids shall be placed between the gun and the bending dipole into the bunching section capable of correcting the beam position.
08/20/2025
In Process
FALSE

F-EIS-PREINJ-LET.10
6.03
Provision shall be made for an appropriate number of air cored steering coils between the gun and bunching section to correct the electron beam position as required.
08/20/2025
In Process
FALSE

F-EIS-PREINJ-LET.11
6.03
A bending dipole shall follow the gun and be able to bend the beam from the gun into the bunching section OR bend separate electron bunches into the separate diagnostic beamline.
08/20/2025
In Process
FALSE

F-EIS-PREINJ-LET.12
6.03
The bending dipole chamber has NEG pumps to differential the gas molecure from the downstream to the gun
08/20/2025
In Process
FALSE

EIS-PREINJ-LET EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-PREINJ-LET.1
6.03.03
The pre-injector shall have a low energy transfer line from the gun into the beam compression "Bunching" section
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.6
6.03.04
Following the gun, there shall be multiple groups of magnets required to control the electron beam.
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

F-EIS-PREINJ-LET.7
6.03.04
To characterize and control the fresh bunches the low energy transfer line from the Gun to the Buncher shall contain a plunging transverse profile monitor, a bunch charge monitor, beam loss monitors, and beam position monitors
05/16/2025
In Process
FALSE

P-EIS-GUN-ESOURCE.01
6.03.04.02
The e-Gun system requires a minimum electrical service 300\208 Amps\Vac
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.02
6.03.04.02
The maximum power consumption required for the Gun systems should not exceed. 108 kVA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.03
6.03.04.02
The gun system shall be designed to operate in a Class 100 (ISO 5) clean room with its temperature maintained at 18 +/- 2 °C
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.04
6.03.04.02
The gun vacuum shall be able to achieve and maintain <10-11 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.05
6.03.04.02
The bunch parameters from the cathode for 5&11GeV operation shall have a bunch charge of 7 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.06
6.03.04.02
The bunch parameters from the cathode for 18GeV operation shall have a bunch charge of 5 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.07
6.03.04.02
The bunch parameters from the cathode shall have a initial bunch length (FWHM) of 1.6 ns
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.08
6.03.04.02
The bunch parameters from the cathode shall have a bunch Diameter(hard edge) within the range of 6-10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.09
6.03.04.02
The bunch parameters from the cathode shall have a Longitudinal profile distribution which is flat
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.10
6.03.04.02
The bunch parameters from the cathode shall have a Transverse Gaussian distribution with a σ of 6 to 10 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.11
6.03.04.02
The bunch parameters from the cathode shall have a Gun voltage in the range of 290 to 350 keV
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.12
6.03.04.02
The gun shall be capable of generating four bunches with each bunch separated by at least 12.8295593046379 µs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.13
6.03.04.02
The gun shall be capable of reproducing the entire 4 bunch pairs with a repetition rate of 1 Hz
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.14
6.03.04.02
For 7[nC] bunches the average current from the gun shall be 56 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.15
6.03.04.02
For 5[nC] bunches the average current from the gun shall be 40 nA
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.17
6.03.04.02
The electron gun design for pre-injector shall permit the exchange of the cathode in Approx 2 hrs
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.16
6.03.04.02
The gun shall have an operational lifetime of >. 2 Wks
05/16/2025
On Hold
FALSE

P-EIS-GUN-ESOURCE.18
6.03.04.02
Minimum e-Beam polarization from gun shall be >85 %
05/16/2025
On Hold
FALSE

EIS-PREINJ-LINAC

EIS-PREINJ-LINAC-INST

EIS-PREINJ-LINAC-VAC

EIS-PREINJ-TLINE

EIS-PREINJ-TLINE-MEBT

EIS-PREINJ-TLINE-MEBT-INST

EIS-PREINJ-TLINE-MEBT-MAG

EIS-PREINJ-TLINE-MEBT-MAG-QUAD

EIS-PREINJ-TLINE-MEBT-RCS

EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR

EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG

EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-CORR

EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-CORR-Pulsed

EIS-PREINJ-TLINE-MEBT-RCS-INJECTOR-MAG-SEP

EIS-PREINJ-TLINE-MEBT-RF

EIS-PREINJ-TLINE-MEBT-RF-FKICK

EIS-PREINJ-TLINE-MEBT-RF-FKICK EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.1
6.08
There shall be a special RF kicker to kick the injected beam into neighboring RF buckets without disturbing the 8 circulating bunches.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.2
6.08
The special kicker shall consist of an RF harmonic kicker with fundamental frequency of 1/4 of the main RCS RF cavity or compatible equivalent alternative.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.3
6.08
The special kicker shall have a rise and fall time that matches the RF bucket size.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.4
6.08
The special kicker shall have a peak power necessary to generate a kick to inject the bunch into the RCS.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.5
6.08
The special kicker shall have a macro pulse with a flattop that is greater than the time between the LINAC bunches and shall have a rise and fall time less than 1 RCS turn.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

F-EIS-PREINJ-TLINE-MEBT-RF-FKICK.6
6.08
The special kicker shall be able to repeat at the LINAC pulse rate.
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.01
6.03.03.05.04
The location (Section) shall be 2 o'clock
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.02
6.03.03.05.04
The dimension in W shall be 5 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.03
6.03.03.05.04
The dimension in L shall be 10 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.04
6.03.03.05.04
The dimension in H shall be 7 (ft)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.05
6.03.03.05.04
The num magnets shall be 1
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.06
6.03.03.05.04
The mag gap shall be tbd (cm)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.07
6.03.03.05.04
The rise time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.08
6.03.03.05.04
The fall time shall be 0.00001 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.09
6.03.03.05.04
The flat top time shall be 0.0000025 (sec)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.10
6.03.03.05.04
The waveshape shall be trap
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.11
6.03.03.05.04
The flat top repeatability shall be tbd %
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.12
6.03.03.05.04
The uniformity of the flattop shall be tbd (V)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.13
6.03.03.05.04
The deflecting Angle shall be 1 (mRad)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.14
6.03.03.05.04
The rep rate spec shall be 100 (Hz)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.15
6.03.03.05.04
The output voltage Spec shall be 5000 (Volts)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.17
6.03.03.05.04
The inductance with cable shall be 4 (uH)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.16
6.03.03.05.04
The output current spec shall be 2300 (Amps)
05/16/2025
In Process
FALSE

P-EIS-RCS-PPD-INJ_RF_KICK.18
6.03.03.05.04
The cooling type shall be water
05/16/2025
In Process
FALSE

EIS-PROT : Protection System

EIS-PROT-ABORT : Protection System Beam Abort

EIS-PROT-COLL : Protection System Collimator

EIS-PROT-DUMP : Protection System Beam Dump

EIS-TLINE

EIS-TLINE-GUN

EIS-TLINE-GUN-Diagnostic

EIS-TLINE-GUN-Diagnostic EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-TLINE-GUN-Diagnostic.1
6.03.04
The Pre-injector separate diagnostic beamline section shall have 3 branches one with Faraday cup, one port containing a connection to the cathode Laser and a line to a low energy beam dump.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

EIS-TLINE-GUN-INST

EIS-TLINE-GUN-INST-Diagnostic

EIS-TLINE-GUN-INST-Diagnostic EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-TLINE-GUN-INST-Diagnostic.1
6.03.04
The instrumentation in the diagnostic beamline to the low energy beam dump shall have the capability to measure beam position, profile, bunch charge
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.01
6.03.04.02.06
The E-gun charge measurement shall use a Mott polarimeter measurement technique.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.02
6.03.04.02.06
The Mott polarimeter shall provide polarization measurements of 280-350 keV electron bunches with an accuracy >=2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.03
6.03.04.02.06
Right and left backscatter acquisition chains shall be incorporated in the design (e-detector, pre-amp, amp, and MCA)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.04
6.03.04.02.06
The Mott polarimeter shall be able to measure the polarization of the electron bunches from the gun.
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.05
6.03.04.02.06
The Mott polarimeter shall read beam polarization over a repolarization range of 25 to 90 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.06
6.03.04.02.06
Over the measurement range the Mott polarimeter shall be accurate to within a resolution of 2 %
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.07
6.03.04.02.06
The Mott polarimeter system and electronics shall utilize ~11 kW, from one 208 Vac 3 phase @ 30 amps/phase circuit (It depends on Mott polarimeter design)
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.08
6.03.04.02.06
The Mott polarimeter shall function @ 18[C] (nom.) within a temperature stability +/- 2[C]supplied by the gun clean room
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.09
6.03.04.02.06
The 280-350 keV Mott polarimeter shall have a bunch charge measurement range of 0.1 to 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-MOT.10
6.03.04.02.06
Th polarimeter shall measure the bunch emittance by slit and beam viewer placed before the 143 deg bending dipole?
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.01
6.03.04.02.06
In the gun diagnostic line an electrostatic bend spin rotator (based on Illinois Univ. design, 1993) shall be used
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.02
6.03.04.02.06
The system shall include two High voltage power supplies and two HV cables
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.04
6.03.04.02.06
The system shall be able to bend the electron spin such that the direction after bending is horizontal
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.03
6.03.04.02.06
When bending at 300 keV the system shall have a bend angle of 143 deg
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-SR.05
6.03.04.02.06
The system shall be able to bend the beam over the range of electron beam energies from 280 to 350 KeV
05/16/2025
On Hold
FALSE

F-EIS-TLINE-GUN-INST-Diagnostic.4
6.03.04
The Faraday cup shall be able to measure the charge of the electron bunches from the gun.
05/16/2025
In Process
FALSE

P-EIS-GUN-INST-F_CUP.02
6.03.04.02.06
The Faraday cup electronics shall require < 3 kW supplied from one 110 Vac, 20 Amp single chase circuit
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.01
6.03.04.02.06
The Faraday cup shall be able to measure the charge of the electron bunches from the gun over a charge range of 0.1 - 14 nC
05/16/2025
On Hold
FALSE

P-EIS-GUN-INST-F_CUP.03
6.03.04.02.06
The Faraday cup power dissipation shall be less that 1 W
05/16/2025
On Hold
FALSE

EIS-TLINE-GUN-LASER

EIS-TLINE-GUN-LASER-INST

EIS-TLINE-GUN-VAC

EIS-TLINE-GUN-VAC-Diagnostic

EIS-TLINE-HEBT

F-EIS-TLINE-HEBT.x1
6.03
The beam extraction from RCS shall be installed in the RCS straight section that is on the near side to the ESR, after the RCS SRF cryomodules
08/20/2025
In Process
FALSE

F-EIS-TLINE-HEBT.1
6.03
The beam injection of the electron bunches from the RCS into the ESR ring shall take place in the 4 o’clock straight section
08/20/2025
In Process
FALSE

F-EIS-TLINE-HEBT.2
6.03
There will be 1 electron bunch circulating in the RCS at extraction, this bunch shall be injected into the RTE transfer line
08/20/2025
In Process
FALSE

F-EIS-TLINE-HEBT.3
6.03
The RTE transfer line shall match the beam parameters between the extraction point of the RCS and injection point of the ESR.
08/20/2025
In Process
FALSE

F-EIS-TLINE-HEBT.4
6.03
The extraction into the RTE transfer line shall match the ESR bunch spacing and spin pattern.
08/20/2025
In Process
FALSE

F-EIS-TLINE-HEBT.5
6.03
The RTE transfer line shall be spin transparent.
08/20/2025
In Process
FALSE

F-EIS-TLINE-HEBT.6
6.03
The RCS extraction system shall have 3 fast bump magnets, a kicker with rise time of 2 micro-secs and a septum magnet.
08/20/2025
In Process
FALSE

F-EIS-TLINE-HEBT.13
6.03
The transferred beam shall meet all the requirements of the circulating beam for all operational modes of the ESR as set forth in [5.9].
08/20/2025
In Process
FALSE

F-EIS-TLINE-HEBT.14
6.03
Each electron bunch from the transfer line shall be injected into ESR in its own injection cycle. In a manner that minimizes the background on the detector system.
08/20/2025
In Process
FALSE

EIS-TLINE-SPIN

EIS-TLINE-SPIN-VAC

EIS-VAC

EIS-VAC EXTERNALS
Requirements who's parents are in other sub-systems.

F-EIS-VAC.1
6.03.04
The EIS vacuum system shall meet UHV standards at a minimum (Ref vacuum spec?)
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.07
6.03.02.04
On 15 m on each side (or one vacuum section) of the SRF cavities the vacuum system shall be processed to class ISO 5.
05/16/2025
Approved
FALSE

F-EIS-VAC.2
6.03.04
The impedance of the entire EIS vacuum system, including the transport lines, shall allow for the bunch intensities, beam currents, and bunch numbers contained in the MPT. [Document#:EIC-SEG-RSI-005]
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.01
6.03.03.03
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.03
6.03.03.03
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.01
6.03.03.03
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.03
6.03.03.03
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.01
6.03.02.04
The vacuum system global impedance shall be less than the impedance budget as provided by accelerator physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.03
6.03.02.04
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.10
6.03.02.04
Copper thickness on beam pipes shall be approved by accelerator physics
05/16/2025
Approved
FALSE

F-EIS-VAC.3
6.03.04
The size, location and type of vacuum pumps shall be chosen to meet the required vacuum levels during operation
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE

F-EIS-VAC.4
6.03.04
Appropriate vacuum gauging shall be supplied in each vacuum sector to monitor the required vacuum levels
05/16/2025
In Process
FALSE

P-EIS-GUN-VAC.01
6.03.04.01.02
Impedance values shall be approved by accelerator physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.02
6.03.04.01.02
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.03
6.03.04.01.02
Special aperture requirements and/or aperture file shall be provided by or approved by physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.04
6.03.04.01.02
The acceptable magnetic field from vacuum equipment within a radius of 16mm or the beam center shall be <0.4 Gauss
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.05
6.03.04.01.02
The magnetic permeability for vacuum equipment shall be approved by beam physics.
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.06
6.03.04.01.02
The average vacuum level after conditioning shall be 10^-10 Torr
05/16/2025
On Hold
FALSE

P-EIS-GUN-VAC.07
6.03.04.01.02
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.06
6.03.03.03
The average vacuum level in all EIS High energy transfer line after conditioning (for 6mts) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-HETL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.06
6.03.03.03
The average vacuum level in all EIS medium energy transfer line after conditioning (for 1000hrs) shall be 5x10^-8 Torr
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.02
6.03.03.03
The typical vacuum chamber aperture shall be 32.9 mm
05/16/2025
On Hold
FALSE

P-EIS-METL-VAC.07
6.03.03.03
The vacuum stability (upper pressure limit) shall be TBD Torr
05/16/2025
On Hold
FALSE

P-EIS-RCS-VAC.02
6.03.02.04
The typical vacuum chamber aperture shall be 32.9 mm diameter.
05/16/2025
Approved
FALSE

P-EIS-RCS-VAC.06
6.03.02.04
The average vacuum level in the entire RCS after conditioning (8mts) shall be 5x10^-8 Torr.
05/16/2025
Approved
FALSE